1. DL manuals
  2. Aaeon
  3. Desktop
  4. FES-6110
  5. User Manual

Aaeon FES-6110 User Manual

Manual is about: Flexible Embedded System 2.5” SATA Hard Disk Drive Bay 1 Gigabit Ethernet/1 COM/ 6 USB2.0 HD Audio Codec (2CH Audio)

Summary of FES-6110

  • Page 1

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 fes-6110 flexible embedded system 2.5” sata hard disk drive bay 1 gigabit ethernet/ 1 com/ 6 usb2.0 hd audio codec (2ch audio) fes-6110 manual 2nd ed. February 2012.

  • Page 2

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m i copyright notice this document is copyrighted, 2012. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual ma...

  • Page 3

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m ii acknowledgments all other products’ name or trademarks are properties of their respective owners.  award is a trademark of award software international, inc.  compactflash ™ is a trademark of the compact flash association.  microsoft ...

  • Page 4

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m iii packing list before you begin operating your pc, please make sure that the following materials are enclosed: 1 fes-6110 1 cd-rom for manual (in pdf format) and drivers 1 60w ac-dc power adapter  1 wallmount kit if any of these items sh...

  • Page 5

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m iv safety & warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any ac outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a dam...

  • Page 6

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m v d. The equipment does not work well, or you cannot get it to work according to the user’s manual. E. The equipment has been dropped and damaged. F. The equipment has obvious signs of breakage. 15. Do not leave this equipment in an environ...

  • Page 7

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m vi below table for china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon boxer/ industrial system 有毒有害物质或元素 部件名称 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 × ○ ○ ○ ○ ○ 外壳 × ○ ○ ○ ○ ○ 中央处理器 与内存 ×...

  • Page 8

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m vii contents chapter 1 general information 1.1 introduction................................................................ 1-2 1.2 features .................................................................... 1-3 1.3 specifications ..........

  • Page 9

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 viii 2.17 rs-232/422/485 serial port connector (com2)..... 2-9 2.18 lpt port connector (lpt1) .................................... 2-9 2.19 lvds inverter (cn1) ............................................... 2-10 2.20 lvds (cn2) ..............

  • Page 10: General

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 chapter 1 general information 1- 1 general chapter 1 information.

  • Page 11

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 1.1 introduction fes-6110 adopts the intel ® atom tm n270 processor, up to 1.6ghz. The chipset is equipped with intel ® 945gse & ich7m. Moreover, the system memory features 200-pin ddrii 400/533 sodimm socket up to 2gb. It deploys one rj-45...

  • Page 12

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 1.2 features z intel ® atom™ n270 1.6 ghz z intel ® 945gse + ich7m chipset z 200-pin non-ecc ddrii 400/533 sodimm x 1, up to 2 gb z dual-view with vga & dvi z realtek pci-express 10/100/1000base-tx ethernet x 1 z 2.5” sata hard disk drive b...

  • Page 13: System

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 1.3 specifications system form factor compact size for desktop/wallmount processor intel ® atom n270 1.6ghz system memory 200-pin ddrii 400/533 sodimm socket x 1, max. 2gb chipset intel ® 945gse & ich7m ethernet 10/100/1000base-tx ethernet ...

  • Page 14: External I/o

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 145mm) weight 3.6 lb (1.62 kg) external i/o serial port rs-232/422/485 x 1 kb & mouse keyboard /mouse x 1 universal serial bus usb2.0 x 6 (2 on the front panel and 4 at i/o) audio audio jack x 2 (mic-in, line-out) ethernet rj-45 x 1 display...

  • Page 15

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 1.4 general system information front panel rear panel chapter 1 general information 1- 6.

  • Page 16: Hardware

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 chapter 2 hardware installation 2-1 hardware installation chapter 2.

  • Page 17

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 2.1 location of jumpers and connectors main board chapter 2 hardware installation 2-2.

  • Page 18: Dio Pin Definition

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 2.2 mechanical drawing dio pin definition chapter 2 hardware installation 2-3.

  • Page 19

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 2.3 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: label function jp1 clear cmos jp3 lvds power selectio...

  • Page 20

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 2.4 list of connectors the board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: label function fp1 front panel connector 1 vga1 vga...

  • Page 21

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 2.5 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cove...

  • Page 22

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 2.6 clear cmos (jp1) jp1 function 1-2 normal (default) 2-3 clear cmos 2.7 lvds power selection (jp3) jp3 function 1-2 +5v 2-3 +3v (default) 2.8 lvds inverter voltage selection (jp4) jp4 function 1-2 +5v 2-3 +12v (default) 2.9 cfd voltage 3....

  • Page 23

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 2.11 com1 port power/ring selection (jp10) jp10 function close 1-2 com1 power selection (default) close 2-3 ri1 2.12 com2 port power/ring selection (jp11) jp11 function close 1-2 com2 power selection (default) close 2-3 ri1 2.13 com2 port p...

  • Page 24

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 9 reset switch (-) 10 reset switch (+) 2.16 rs-232 serial port connector (com1, com3, com4) pin signal pin signal 1 dcd 2 rxd 3 txd 4 dtr 5 gnd 6 dsr 7 rts 8 cts 9 ri 10 n.C 2.17 rs-232/422/485 serial port connector (com2) pin signal pin si...

  • Page 25

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 11 data4 12 gnd 13 data5 14 gnd 15 data6 16 gnd 17 data7 18 gnd 19 #ack 20 gnd 21 busy 22 gnd 23 pe 24 gnd 25 select 26 gnd 2.19 lvds inverter (cn1) pin signal 1 12v / 5v 2 vcon 3 +5v 4 gnd 5 bkl_en 2.20 lvds (cn2) pin signal pin signal 1 b...

  • Page 26

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 19 lb_tx0# 20 lb_tx0 21 lb_tx1# 22 lb_tx1 23 lb_tx2# 24 lb_tx2 25 n.C. 26 n.C. 27 vlcd 28 gnd 29 lb_clk# 30 lb_clk 2.21 audio pin header (right channel) (cn4) pin signal pin signal 1 spk_ro+ 2 spk_ro- 2.22 audio pin header (left channel) (c...

  • Page 27

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 7 in7/out7 8 in8/out8 9 +5v 10 gnd 2.25 ps/2 keyboard/mouse connector (cn8) pin signal 1 kb_data 2 ms-data 3 gnd 4 +5v 5 kb_clk 6 ms_clk 2.26 sata power connector (pwr1, 2) pin signal pin signal 1 +12v 2 gnd 3 gnd 4 +5v 2.27 audio connector...

  • Page 28

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 2.28 installing the hard disk drive step 1: unfasten the five screws on the bottom case of fes-6110. Step 2 : fasten the four hdd rubbers(blue) on the hdd bracket chapter 2 hardware installation 2-13.

  • Page 29

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 step3 : fasten the 4 screws to connect hdd bracket and hdd step 4 : put hdd on the bottom case of fes-6110 and then fasten 4 screws to fix on it. Chapter 2 hardware installation 2-14.

  • Page 30

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 chapter 2 hardware installation 2-15 step 5: put the bottom case back to the system and plug in sata cable and power cable. Step 6: close and screw the bottom case of the fes-6110

  • Page 31: Award

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 chapter 3 award bios setup 3-1 award chapter 3 bios setup.

  • Page 32

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of ...

  • Page 33: Entering Setup

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 3.2 award bios setup awards bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram so that it retains the setup information when the po...

  • Page 34: Pc Health Status

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 pc health status this menu allows you to set the shutdown temperature for your system. Frequency/voltage control use this menu to specify your settings for auto detect dimm/pci clock and spread spectrum. Load fail-safe defaults use this men...

  • Page 35: Driver

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 chapter 4 driver installation 4-1 driver chapter 4 installation.

  • Page 36

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 the fes-6110 comes with an autorun cd-rom that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver cd, the driver cd-title will auto start and show the installation guide. If not, plea...

  • Page 37

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 4.1 installation: insert the fes-6110 cd-rom into the cd-rom drive and install the drivers from step 1 to step 5 in order. Step 1 – install inf driver 1. Click on the step 1-inf folder and double click on the setup.Exe 2. Follow the instruc...

  • Page 38

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 system is 2. Double click on setup.Exe located in each os folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically step 5 – install video decoder 1. Click on the step 5-video decod...

  • Page 39: Programming The

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m appendix a programming the watchdog timer a-1 programming the appendix a watchdog timer.

  • Page 40

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m appendix a programming the watchdog timer a-2 a.1 programming fes-6110 utilizes ite 8718 chipset as its watchdog timer controller. ( k version ) below are the procedures to complete its configuration and the aaeon intial watchdog timer prog...

  • Page 41

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 appendix a programming the watchdog timer a-3 (1) enter the mb pnp mode to enter the mb pnp mode, four special i/o write operations are to be performed during wait for key state. To ensure the initial state of the key-check logic, it is nec...

  • Page 42

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 appendix a programming the watchdog timer a-4 bit description 7-2 reserved 1 returns to the wait for key state. This bit is used when the configuration sequence is completed. 0 resets all logical devices and restores configuration registers...

  • Page 43

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 appendix a programming the watchdog timer a-5 default=00h) bit description 7-0 wdt time-out value 7-0 watchdog timer time-out value (msb) register (index=74h, default=00h) bit description 7-0 wdt time-out value 15-8 a.2 ite8718 watchdog tim...

  • Page 44

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 appendix a programming the watchdog timer a-6 call superio_set_reg ;clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call superio_set_reg ;unit is second. Mov al, 0c0h mov cl, 72h call superio_set_reg ; game port enable mov cl,...

  • Page 45

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 appendix a programming the watchdog timer a-7 out dx,al inc si loop init_1 ret enter_configuration_mode endp exit_configuration_mode proc near mov ax,0202h call write_configuration_data ret exit_configuration_mode endp check_chip proc near ...

  • Page 46

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 appendix a programming the watchdog timer a-8 stc ret not_initial: clc ret check_chip endp read_configuration_data proc near mov dx,word ptr cs:[cfg_port+04h] out dx,al mov dx,word ptr cs:[cfg_port+06h] in al,dx ret read_configuration_data ...

  • Page 47

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 appendix a programming the watchdog timer a-9 mov dx,word ptr cs:[cfg_port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret superio_set_reg endp.Set_logic_device proc near set_logic_device proc near push ax push cx xchg al,cl mov cl,07h...

  • Page 48

    F l e x i b l e e m b e d d e d s y s t e m f e s - 6 1 1 0 appendix a programming the watchdog timer a-10 end main note: interrupt level mapping 0fh-dh: not valid 0ch: irq12 . . 03h: irq3 02h: not valid 01h: irq1 00h: no interrupt selected.

  • Page 49: I/o Information

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m appendix b i/o information b - 1 i/o information appendix b.

  • Page 50

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m appendix b i/o information b-2 b.1 i/o address map.

  • Page 51

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m appendix b i/o information b-3 b.2 memory address map.

  • Page 52

    F l e x i b l e e m b e d d e d f e s - 6 1 1 0 s y s t e m appendix b i/o information b-4 b.3 irq mapping chart b.4 dma channel assignments.