1. DL manuals
  2. Aaeon
  3. Server
  4. FWS-7810
  5. User Manual

Aaeon FWS-7810 User Manual - Chapter 3 Ami Bios Setup

Manual is about: 1u rackmount network appliance platform

Summary of FWS-7810

  • Page 1

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 fws-7810 1u rackmount network appliance platform 2 sata 6.0 gb/s, 2 usb3.0 1 pci-e[x8] (optional) 1 nim (optional) fws-7810 manual 1st ed. December 2013.

  • Page 2

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 i copyright notice this document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduc...

  • Page 3

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 ii acknowledgments all other products ’ name or trademarks are properties of their respective owners. Ami is a trademark of american megatrends inc. Compactflash ™ is a trademark of the compact flash association. Intel ® , core ® , and xeon quad core, a...

  • Page 4

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 iii packing list before you begin installing your card, please make sure that the following materials have been shipped: 1 fws-7810 1 dvd-rom for manual (in pdf format) and drivers 2 sata hdd cable 2 serial ata cable 1 rj-45 console cable 1 cpu heatsink...

  • Page 5: Chapter 3 Ami Bios Setup

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 iv contents chapter 1 general information 1.1 introduction ................................................................ 1-2 1.2 features .................................................................... 1-3 1.3 specifications .......................

  • Page 6

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 v 3.2 ami bios setup ........................................................ 3-3 chapter 4 driver installation 4.1 installation ................................................................. 4-3 appendix a programming the watchdog timer a.1 watchdog...

  • Page 7: General

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 1 general information 1- 1 general information chapter 1.

  • Page 8

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 1 general information 1- 2 1.1 introduction fws-7810 adopts intel® 4 th generation core ™ / xeon series processor. The chipset is equipped with intel ® c226. In addition, the system memory features four 240-pin ecc ddr3 1333/1600 mhz dimm up to ...

  • Page 9

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 1 general information 1- 3 1.2 features 1u rackmount 8 lan ports network appliance intel ® 4 th generation core ™ /xeon processor 240-pin dual-channel ecc ddr3 1333/1600mhz dimm x 4 (up to 32 gb) gigabit ethernet x 8 with optional 2-pair lan byp...

  • Page 10: System

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 1 general information 1- 4 1.3 specifications system form factor 1u 8-port network appliance processor intel ® 4th generation core ™/ xeon system memory 240-pin dual-channel ecc ddr3 1333/1600 dimm socket x 4, up to 32 gb chipset intel ® c226 et...

  • Page 11: Display

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 1 general information 1- 5 hdd active led x 1 usb port x 2 rj-45 port with led x 8 rj-45 console x 1 lcm display and 4 keypad x 1 software programming switch x 1 rear i/o panel ac power input x 1 power switch x 1 expansion slot x 2 (optional pci...

  • Page 12: Environmental

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 1 general information 1- 6 environmental operating temperature 32 o f~104 o f (0 o c~40 o c) storage temperature -4 o f~140 o f (-20 o c~60 o c) operating humidity 10~80% relative humidity, non-condensing storage humidity 10~80% @ 40 o c, non-co...

  • Page 13

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 1 general information 1- 7 1.4 general system information front view rear view lcm panel led 10/100/1000base-tx x 9 usb2.0 x 2 expansion slots power switch ac power input.

  • Page 14: Quick

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-1 quick installation guide chapter 2.

  • Page 15

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-2 2.1 safety precautions the installation is intended for technically qualified personnel who have experience installing and configuring system boards. The equipment can be installed in a restricted access location (...

  • Page 16

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-3 2.2 location of connectors board of fws-7810 component side.

  • Page 17

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-4 solder side.

  • Page 18

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-5 2.3 mechanical drawings of fws-7810

  • Page 19

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-6 2.4 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: label function jp2 auto pow...

  • Page 20

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-7 lan1 10/100/1000 base-tx ethernet connector lan2 10/100/1000 base-tx ethernet connector lan3 10/100/1000 base-tx ethernet connector lan4 10/100/1000 base-tx ethernet connector lan5 10/100/1000 base-tx ethernet conn...

  • Page 21

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-8 2.6 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often p...

  • Page 22

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-9 2.7 clear cmos (cmos) cmos function 1-2 protected (default) 2-3 clear 2.8 auto power button (jp2) jp2 function 1-2 power on by button (default) 2-3 auto power on 2.9 front panel connector (fp1) pin signal pin signa...

  • Page 23

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-10 2.11 usb3.0 port pin header pin signal pin signal 1 vcc 20 nc 2 usb3_rx1_dn_c 19 vcc 3 usb3_rx1_dp_c 18 usb3_rx2_dn_c 4 gnd 17 usb3_rx2_dp_c 5 usb3_tx1_dn_c 16 gnd 6 usb3_tx1_dp_c 15 usb3_tx2_dn_c 7 gnd 14 usb3_tx...

  • Page 24

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-11 2.12 installing the cpu and the heat sink step 1: loosen the screws and remove the fan duct step 2: release the lock pole of the cpu bracket.

  • Page 25

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-12 step 3: lift up the cpu bracket.

  • Page 26

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-13 step 4 : lift up the cpu cover step 5 : place the cpu to the socket and have the two fillisters locked properly.

  • Page 27

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-14.

  • Page 28

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-15 step 6 : close the cpu bracket and lock the pole to the position.

  • Page 29

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-16 step 7 : cover the heatsink on the cpu and watch out the direction of the heatsink that did not against the airflow step 8: fasten the four screws to lock the air duct.

  • Page 30

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-17 2.13 installing the two 2.5” hard disk drive (hdd) step 1: unscrew the upper lid step 2: unfasten the four screws step 3: put the screw into cushion.

  • Page 31

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-18 step 4: put the assembled cushions to the upper place of the 2.5 ” hdd bracket step 5: put the assembled cushions to the lower place of the 2.5 ” hdd.

  • Page 32

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-19 bracket step 6: lock the hdd to the lower cushions with four screws step 7: lock the second hdd to the upper cushions with four screws.

  • Page 33

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-20 step 8: lock the hdd bracket to the chassis with four screws step 9: connect the sata cable and power cable to the hdd in lower place.

  • Page 34

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-21 step 10: connect the sata cable and power cable to the hdd in upper place.

  • Page 35

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-22 2.14 installing the network interface module (nim) step 1: unfasten the screws on the bottom of chassis.

  • Page 36

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-23 step 2 : remove the null module cover or existing lan module.

  • Page 37

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-24 step 3 : insert the lan module and fasten the screws on the chassis.

  • Page 38

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-25.

  • Page 39

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 2 quick installation guide 2-26 below table for china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon boxer/ industrial system 部件名称 有毒有害物质或元素 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 × ○ ○ ○ ○ ○ 外壳...

  • Page 40: Ami

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-1 ami bios setup chapter 3.

  • Page 41

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-2 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There a...

  • Page 42

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-3 3.2 ami bios setup ami bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram so that it retains the setup information ...

  • Page 43

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-4 setup menu setup submenu: main.

  • Page 44

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-5 setup submenu: advanced.

  • Page 45

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-6 super io configuration.

  • Page 46

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-7 serial port 1 configuration options summary: serial port disabled enabled enable or disable serial port (com) serial port auto io=3f8h; irq=4; io=3f8h; irq=3,4,5,6,7,9,10,11,12; io=2f8h; irq=3,4,5,6,7,9,10,11,12; io=3e8h; ir...

  • Page 47

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-8 serial port 2 configuration options summary: serial port disabled enabled enable or disable serial port (com) serial port auto io=2f8h; irq=3; io=3f8h; irq=3,4,5,6,7,9,10,11,12; io=2f8h; irq=3,4,5,6,7,9,10,11,12; io=3e8h; ir...

  • Page 48

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-9 parallel port configuration options summary: parallel port disabled enabled enable or disable serial port (com) change settings auto io=378h; irq=5; io=378h; irq=5,6,7,9,10,11,12; io=278h; irq=5,6,7,9,10,11,12; io=3bch;irq=5...

  • Page 49

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-10 h/w monitor.

  • Page 50

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-11 smart fan function options summary: smart fan mode full on mode automatic mode manual mode smart fan mode select fan off temperature limit 15 (0-127) fan will of when temperature lower than this limit. Fan start temperature...

  • Page 51

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-12 pwm slope setting 0.125 pwm 0.25 pwm 0.5 pwm 1 pwm 2 pwm 4 pwm 8 pwm 15.875 pwm pwm slope selection.

  • Page 52

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-13 serial port console redirection options summary: console redirection disabled (com2) enabled (com1) console redirection enabled or disabled..

  • Page 53

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-14 console redirection settings options summary: terminal type vt100 vt100+ vt-utf8 ansi emulation: ansi: extended ascii char set. Vt100: ascii char set. Vt100+: extends vt100 to support color, function keys, etc. Vt-utf8: use...

  • Page 54

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-15 parity none even odd mark space a parity bit can be sent with the data bits to detect some transmission errors. Even: parity bit is 0 if the num of 1 ’s in the data bits is even. Odd: parity bit is 0 if num of 1 ’s in the d...

  • Page 55

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-16 vt-utf8 combo key support disabled enabled enable vt-utf8 combination key support for ansi/vt100 terminals recorder mode disabled enabled on this mode enabled only text will be send. This is to capture terminal data. Resolu...

  • Page 56

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-17 power management options summary: power mode atx type at type select power supply mode. Acpi sleep state suspend disabled s3 only (suspend to ram) select acpi sleep state the system will enter when the suspend button is pre...

  • Page 57

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-18 cpu configuration.

  • Page 58

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-19 options summary : hyper-threading disabled enabled enabled for windows xp and linux (os optimized for hyper-threading technology) and disabled for other os (os not optimized for hyper-threading technology). When disabled on...

  • Page 59

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-20 sata configuration (ide) options summary : sata controller(s) disabled enabled enable or disable sata device. Sata mode selection ide ahci raid determines how sata controller(s) operate..

  • Page 60

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-21 sata configuration (ahci) options summary : sata controller speed disabled enabled enable or disable sata device. Sata mode selection default gen1 gen2 gen3 indicates the maximum speed the sata controller can support. Port ...

  • Page 61

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-22 sata device type hard disk drive solid state drive indentify the sata port is connected to solid state drive or hard disk drive. Spin up device disabled enabled on an edge detect from 0 to 1, the pch starts a comreset initi...

  • Page 62

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-23 sata configuration (raid) options summary : sata controller speed disabled enabled enable or disable sata device. Sata mode selection default gen1 gen2 gen3 indicates the maximum speed the sata controller can support. Port ...

  • Page 63

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-24 sata device type hard disk drive solid state drive indentify the sata port is connected to solid state drive or hard disk drive. Spin up device disabled enabled on an edge detect from 0 to 1, the pch starts a comreset initi...

  • Page 64

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-25 usb configuration options summary: legacy usb support enabled disabled auto enables legacy usb support. Auto option disables legacy support if no usb devices are connected. Disable option will keep usb device available only...

  • Page 65

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-26 lan bypass configuration options summary : status led ctrl led off red led on red led blink red led fast blink green led on green led blink green led fast blink status led ctrl help. Lan kit power on bypass passtru setting ...

  • Page 66

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-27 wdt bypass reset wdt function select, reset: reset system. Bypass: reset lan kits to bypass mode..

  • Page 67

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-28 setup submenu: chipset.

  • Page 68

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-29 pch-io configuration options summary: pci-e lan port n disabled enabled control the pci express root port..

  • Page 69

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-30 system agent (sa) configuration options summary : vt-d disabled enabled check to enable vt-d function on mch. Memory configuration.

  • Page 70

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-31.

  • Page 71

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-32 boot options summary : quite boot disabled enabled enables or disables quiet boot option. Launch 82574l # pxe disabled enabled enable or disable legacy boot option for 82574 # ..

  • Page 72

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-33 security change user/supervisor password you can install a supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features...

  • Page 73

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 3 ami bios setup 3-34 setup submenu: exit.

  • Page 74: Driver

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 4 driver installation 4-1 driver installation chapter 4.

  • Page 75

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 4 driver installation 4-2 the fws-7810 comes with an autorun dvd-rom that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver dvd, the driver dvd-title will auto start and show the installa...

  • Page 76

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 4 driver installation 4-3 4.1 installation insert the fws-7810 dvd-rom into the dvd-rom drive and install the drivers from step 1 to step 5 in order. Step 1 – install chipset driver 1. Click on the step1 - chipset folder and double click on the ...

  • Page 77

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 chapter 4 driver installation 4-4 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically step 5 – install me driver 1. Click on the step5 - me folder and double click on the setup.Exe file 2. Follow...

  • Page 78: Programming The

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix a programming the watchdog timer a-1 programming the watchdog timer appendix a.

  • Page 79

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix a programming the watchdog timer a-2 a.1 watchdog timer initial program table 1 : superio relative register table default value note index 0x2e (note1) sio mb pnp mode index register 0x2e or 0x4e data 0x2f (note2) sio mb pnp mode data register ...

  • Page 80

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix a programming the watchdog timer a-3 ************************************************************************************ // superio relative definition (please reference to table 1) #define byte sioindex //this parameter is represented from no...

  • Page 81: Main

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix a programming the watchdog timer a-4 ************************************************************************************ void main (){ // procedure : aaeonwdtconfig // (byte)timer : time of wdt timer.(0x00~0xff) // (boolean)unit : select time ...

  • Page 82

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix a programming the watchdog timer a-5 ************************************************************************************ // procedure : aaeonwdtenable void aaeonwdtenable () { wdtenabledisable( enableldn , enablereg , enablebit , 1 ); } // pro...

  • Page 83

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix a programming the watchdog timer a-6 ************************************************************************************ void sioentermbpnpmode() { switch( sioindex ){ case 0x2e: iowritebyte(sioindex, 0x87); iowritebyte(sioindex, 0x01); iowrit...

  • Page 84

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix a programming the watchdog timer a-7 ************************************************************************************ void siobitset(byte ldn, byte register, byte bitnum, byte value) { byte tmpvalue; sioentermbpnpmode(); sioselectldn(byte l...

  • Page 85: I/o  Information

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix b i/o information b - 1 i/o information appendix b.

  • Page 86

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix b i/o information b-2 b.1 i/o address map.

  • Page 87

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix b i/o information b-3 b.2 memory address map.

  • Page 88

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix b i/o information b-4 b.3 irq mapping chart.

  • Page 89

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix b i/o information b-5.

  • Page 90

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix b i/o information b-6.

  • Page 91

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix b i/o information b-7.

  • Page 92

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix b i/o information b-8 b.4 dma channel assignments.

  • Page 93: Standard  Lan  Bypass

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-1 standard lan bypass platform setting appendix c.

  • Page 94

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-2 c.1 status led introduction fws-7810 provides a led indicator which can change the led status by aaeon sdk. User is able to program the led status to express different status. Status led configuration ...

  • Page 95: Main

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-3 sample code ************************************************************************************ #define word led2add //this parameter is represented from note1 #define word led1add //this parameter is...

  • Page 96

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-4 c.2 lan bypass introduction fws-7810 provides lan bypass kit and allow uninterrupted network traffic even if a single in-line appliance is shut down or hangs. Customer can upgrade to 2 or 4 lan bypass ...

  • Page 97

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-5 pwr_on use for configuring lan bypass function behavior to lan kit, when system power on. 1: bypass 0: pass through pwr_off use for configuring lan bypass function behavior to lan kit, when system powe...

  • Page 98

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-6 act_en r/w 0xa00 (note7) 5 (note14) (note15) ************************************************************************************ sample code ***********************************************************...

  • Page 100

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-8 bypass_active (act_en, act_en_r); } ************************************************************************************.

  • Page 101

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-9 c.3 lcd module introduction fws-7810 provides a lcm (lcd module) to display information via standard parallel port. User is able to program the lcm to express different status. Sample code void display...

  • Page 102

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-10 } void entry_mode_set() { outportb(0x378, 0x06); wait(); outportb(0x37a, 0xc8); wait(); outportb(0x37a, 0xca); wait(); } void display_off() { outportb(0x378, 0x08); wait(); outportb(0x37a, 0xc8); wait...

  • Page 103

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-11 wait(); outportb(0x37a, 0xca); wait(); } void display_on_cursor_on() { outportb(0x378, 0x0e); wait(); outportb(0x37a, 0xc8); wait(); outportb(0x37a, 0xca); wait(); }.

  • Page 104

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-12 c.4 software reset button (general propose input) introduction fws-7810 provides a general propose input button which status can get by aaeon sdk. Soft reset button configuration table 2 : lan bypass ...

  • Page 105: Main

    N e t w o r k ap p l i a n c e f w s - 7 8 1 0 appendix c standard lan bypass platform setting c-13 tmpvalue = inportb (ioaddr); return (tmpvalue & (1 } ************************************************************************************ void main (){ byte rstbtn; rstbtn = get_value (btn_sts, btn_st...