1. DL manuals
  2. Aaeon
  3. Single board computers
  4. GENE-5315
  5. User Manual

Aaeon GENE-5315 User Manual

Manual is about: SubCompact Board

Summary of GENE-5315

  • Page 1

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 gene-5315 amd ® geode lx800/900 series processors rtl8139dl for 10/100mbps type ii compactflash 2 com (rev.A), 5 com (rev.B) 4 usb2.0, 1 irda type iii mini pci gene-5315 manual rev.A + b 4th ed. November 2009.

  • Page 2

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 i copyright notice this document is copyrighted, 2009. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reprodu...

  • Page 3

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 ii acknowledgments all other products’ name or trademarks are properties of their respective owners. Award is a trademark of award software international, inc. Compactflash™ is a trademark of the compact flash association. Amd, the amd arrow logo and c...

  • Page 4

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 iii packing list before you begin installing your card, please make sure that the following materials have been shipped: • 1 9681531501 cable kit for gene-5315 1700060192 keyboard & mouse cable 1709100201 usb cable 1701440500 ide cable 3.5” • 1 9657666...

  • Page 5

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 iv contents chapter 1 general information 1.1 introduction................................................................ 1-2 1.2 features .................................................................... 1-3 1.3 specifications .......................

  • Page 6

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 v 2.17 usb port #1 and port #2 (cn5) .............................. 2-17 2.18 digital i/o connector (cn6) .................................... 2-17 2.19 audio input/output/cdin/mic (cn7)........................ 2-18 2.20 atx external 5vsb (cn8) ..........

  • Page 7

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 vi 2.40 compact flash disk slot (cfd1) .......................... 2-29 2.41 mini-pci slot (mpci1) ........................................... 2-30 2.42 ddr sodimm slot (dimm1) ................................. 2-30 chapter 3 award bios setup 3.1 system...

  • Page 8

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 vii b.5 dma channel assignments ...................................B-3 appendix c mating connector c.1 list of mating connectors and cables.................. C-2.

  • Page 9: General

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 1 general information 1- 1 general chapter 1 information.

  • Page 10

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 1 general information 1- 2 1.1 introduction aaeon, a leading embedded boards manufacturer, is pleased to announce the debut of their new generation 3.5” subcompact board —gene-5315. The gene-5315 not only completes aaeon’s product line of subco...

  • Page 11

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 1 general information 1 - 3 1.2 features onboard amd geode lx 800/lx900 processors sodimm ddr 333 max. 1gb, ddr 400 max. 512mb up to 24-bit single channel lvds tft lcd dual 10/100mbps ethernet type iii mini-pci and pc/104 (for rev.A only) expan...

  • Page 12

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 1 general information 1- 4 1.3 specifications system processor onboard amd geode lx800/ lx900 series processor system memory 200-pin ddr sodimm x 1, max. 1gb for ddr333 and 512mb for ddr 400 chipset amd lx series + cs5536 i/o chipset ite it8712...

  • Page 13: I/o

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 1 general information 1 - 5 display supports crt/lcd simultaneous display chipset amd lx series + ti sn75lvds83 memory shared system memory up to 254 mb lcd interface up to 24-bit ttl/lvds tft lcd resolution up to 1920 x 1440 @ 24bpp for crt up...

  • Page 14: Quick

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 1 quick installation chapter 2 guide notice: the quick installation guide is derived from chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual cd-rom ...

  • Page 15

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 2 2.1 safety precautions always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensiti...

  • Page 16

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 3 2.2 jumpers, connectors, and mechanical drawings gene-5315 rev.A component side cn7 cn3 cn6 cn5 cn2 cn8 cn1 cn11 cn4 cn 10 jp4 cn14 cn20 cn18 jp5 cn19 cn13 cn16 cn15 cn17 cn9 mpci1 jp3 bat1 cn 2 2 jp2 jp6 cn 12 ...

  • Page 17

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 4 solder side dimm1 cfd1 0.00 0.00 30.4 9 12.43 52.59 34.84 132.84 66.04.

  • Page 18

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 5 mechanical drawings 0.00 0. 00 8.89 3. 22 7.35 1.1 9 50.46 92.07 125.56 0. 63 133.93 0. 00 18. 6 7 123.73 108.27 97.98 5. 13 132.56 132.27 85 .7 6 95 .2 0 133.93 98 .3 8 137.16 119.27 106.68 91 .9 3 91.07 91 .7 ...

  • Page 19

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 6 gene-5315 rev.B component side cn6 jp5 cn16 mp c i1 cn3 cn8 cn9 cn5 cn7 cn2 cn1 bat1 jp3 jp2 jp7 cn4 cn21 jp1 jp 6 cn 22 cn 26 cn2 4 cn 25 cn 2 3 cn1 7 cn15 cn13 cn19 cn18 cn14 cn20 cn 1 0 cn 9 cn 1 2 jp 4.

  • Page 20

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 7 solder side dimm1 cfd1 8.89 98.38 30.49 12.43 52.53 34 .8 4 132.84 66.04 0.00 0.00

  • Page 21

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 8 mechanical drawings 8.89 96.14 95.20 74.31 60.21 46.11 36.78 19.44 10.49 10.27 0.00 1.13 6.10 0.00 14.61 33.66 59.49 47.18 61.13 91.07 114.94 133.93 125.75 106.60 95.20 87.67 85.76 53.28 26.62 5.13 0.00 3.23 137...

  • Page 22

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 9 2.3 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: label function jp1 at/at...

  • Page 23

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 10 2.4 list of connectors the board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each of the board’s connectors: note: for furt...

  • Page 24

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 11 cn18 mini-din ps/2 cn19 serial port #1 cn20 crt display cn21 usb port #3 and port #4 cn22 lcd inverter voltage cn23 serial port #3 (for rev. B only) cn24 serial port #5 (for rev. B only) cn25 serial port #4 (fo...

  • Page 25

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 12 2.5 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (oft...

  • Page 26

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 13 2.6 at/atx power type selection (jp1) jp1 function 1-2 atx power supply at power supply (default) 2.7 cfd master/slave selection (jp2) jp2 function 1-2 slave 2-3 master (default) 2.8 clear cmos (jp3) jp3 functi...

  • Page 27

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 14 2.10 com ports ri/+5v/+12v selection (jp5) com 1 jp5 function 1-2 +12v 3-4 +5v 5-6 ri (default) com 2 jp5 function 7-8 +12v 9-10 +5v 11-12 ri (default) 2.11 inverter voltage selection (jp6) jp6 function 1-2 +5v...

  • Page 28

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 15 5 d6 6 d9 7 d5 8 d10 9 d4 10 d11 11 d3 12 d12 13 d2 14 d13 15 d1 16 d14 17 d0 18 d15 19 ground 20 n.C. 21 dreq 22 ground 23 iow# 24 ground 25 ior# 26 ground 27 iordy 28 ground 29 dack# 30 ground 31 irq14 32 n.C...

  • Page 29

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 16 7 ground 8 index# 9 ground 10 mtra# 11 ground 12 drvb# 13 ground 14 drva# 15 ground 16 mtrb# 17 ground 18 dir# 19 ground 20 step# 21 ground 22 wdata# 23 ground 24 wgate# 25 ground 26 trk0# 27 ground 28 wpt# 29 ...

  • Page 30

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 17 25 slct 26 n.C. 2.16 front panel connector (cn4) pin signal pin signal 1 power on button (-) 2 power on button (+) 3 ide led (-) 4 ide led (+) 5 external buzzer (-) 6 external buzzer (+) 7 power led (-) 8 power...

  • Page 31

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 18 dio-2 cn6 pin 2 bit 6 u1 pin 21 (gpio 26) dio-3 cn6 pin 3 bit 5 u1 pin 22 (gpio 25) dio-4 cn6 pin 4 bit 4 u1 pin 23 (gpio 24) dio-5 cn6 pin 5 bit 3 u1 pin 24 (gpio 23) dio-6 cn6 pin 6 bit 2 u1 pin 25 (gpio 22) ...

  • Page 32

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 19 6 +5 volt. Standby 2.21 4p power socket (cn9) pin signal 1 +12 volt. 2 ground 3 ground 4 +5 volt. 2.22 lvds lcd connector (cn10) pin signal pin signal 1 n.C. 2 n.C. 3 vdd 4 ground 5 clk- 6 clk+ 7 vdd 8 ground 9...

  • Page 33

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 20 2.23 pc/104 (cn11) (for rev. A only) j1/p1 pin a b 1 iochck* gnd 2 d7 rstdrv 3 d6 +5v 4 d5 irq9 5 d4 -5v 6 d3 drq2 7 d2 -12v 8 d1 endxfr* 9 d0 +12v 10 iochrdy gnd/key 11 aen smemw* 12 a19 smemr* 13 a18 iow* 14 ...

  • Page 34

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 21 29 a2 +5v 30 a1 osc 31 a0 gnd 32 gnd gnd j2/p2 pin d c 1 gnd gnd 2 memcs16* sbhe* 3 iocs16* la23 4 irq10 la22 5 irq11 la21 6 irq12 la20 7 irq15 la19 8 irq14 la18 9 dack0* la17 10 drq0 memr* 11 dack5* memw* 12 d...

  • Page 35

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 22 geode’s architecture limitation. The following steps for setup the resources manually for your reference. 1. Retrieve the resource of the pc/104 card. The information is typically contained in the manual of the...

  • Page 36

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 23 25 r0 26 r1 27 r2 28 r3 29 r4 30 r5 31 r6 32 r7 33 ground 34 ground 35 clock 36 vsync 37 de 38 hsync 39 n.C. 40 n.C. For 18-bit tft lcd pin signal pin signal 1 +5volt. 2 +5volt. 3 ground 4 ground 5 +3.3volt. 6 ...

  • Page 37

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 24 37 de 38 hsync 39 n.C. 40 n.C. 2.25 serial port #2 (cn13) com2/ rs-232 mode pin signal pin signal 1 dcdb 2 rxb 3 txb 4 dtrb 5 ground 6 dsrb 7 rtsb 8 ctsb 9 rib (+5v/ +12v) 10 n.C. Com2/ rs-422 mode pin signal p...

  • Page 38

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 25 2 +5 volt. 3 ground 2.27 ethernet 10/100 base-tx rj-45 phone jack #1 (cn15) pin signal pin signal 1 rxd- 2 rxd+ 3 rct 4 n.C. 5 n.C. 6 tct 7 txd- 8 txd+ 9 act_led 10 link_led 11 +3.3 volt. 12 spd_led 13 ground 1...

  • Page 39

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 26 4 ground 5 tx 6 cir_rx (option) 2.30 mini-din ps/2 keyboard/ mouse connector (cn18) pin signal pin signal 1 keyboard data 2 keyboard data 3 ground 4 ground 5 +5 volt. 6 +5 volt. 7 shield 8 shield 2.31 serial po...

  • Page 40

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 27 8 ground 2.33 usb port #3 and port #4 (cn21) pin signal pin signal 1 vdd 2 ground 3 d2- 4 ground 5 d2+ 6 d3+ 7 ground 8 d3- 9 ground 10 vdd 2.34 lcd inverter voltage (cn22) pin signal 1 vcc 2 backlight control ...

  • Page 41

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 28 2.36 serial port #5 (cn24) (for rev.B only) com 5 pin signal pin signal 1 dcd5 2 rx5 3 tx5 4 dtr5 5 ground 6 dsr5 7 rts5 8 cts5 9 ri5 10 n.C. Note: an apm mode limitation, os (operating system) recognizes seria...

  • Page 42

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 29 note: an apm mode limitation, os (operating system) recognizes serial port 5 & 6 of gene-5315 rev.B but is reverse. Os will reassign irq and give sequence of serial port 5 & 6 after uninstalling all of serial p...

  • Page 43

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 30 19 da1 44 dack# 20 da0 45 dasp# 21 d0 46 pdiag# 22 d1 47 d8 23 d2 48 d9 24 io16# 49 d10 25 ground 50 ground 2.41 mini-pci slot (mpci1) standard specification 2.42 ddr sodimm slot (dimm1) standard sodimm slot no...

  • Page 44

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 2 quick installation guide 2 - 31 below table for china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon main board/ daughter board/ backplane 有毒有害物质或元素 部件名称 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线...

  • Page 45: Award

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 3 award bios setup 3-1 chapter award bios setup 3.

  • Page 46

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 3 award bios setup 3-2 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. Ther...

  • Page 47: Entering Setup

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 3 award bios setup 3-3 3.2 award bios setup awards bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram so that it retains the setup info...

  • Page 48: Advanced Chipset Features

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 3 award bios setup 3-4 advanced chipset features use this menu to change the values in the chipset registers and optimize your system performance. Integrated peripherals use this menu to specify your settings for integrated peripherals. (primar...

  • Page 49: Load Optimized Defaults

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 3 award bios setup 3-5 load optimized defaults use this menu to load the bios default values that are factory settings for optimal performance system operations. While award has designated the custom bios to maximize performance, the factory ha...

  • Page 50: Driver

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 4 driver installation 4 - 1 chapter driver 4 installation.

  • Page 51

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 4 driver installation 4 - 2 4.1 software drivers this chapter describes the operation and installation of the display drivers supplied on the supporting cd-rom that are shipped with your product. The onboard vga adapter is based on the amd lx v...

  • Page 52

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 4 driver installation 4 - 3 4.2 necessary to know the instructions in this manual assume that you understand elementary concepts of ms-dos and the ibm personal computer. Before you attempt to install any driver from the supporting cd-rom, you s...

  • Page 53

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 4 driver installation 4 - 4 4.3 installing vga driver win xp / win xpe vga place the driver cd-rom into your cd-rom drive and follow the steps below to install. 1. Click on start button. 2. Click on settings button. 3. Click on control panel bu...

  • Page 54

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 4 driver installation 4 - 5 4.4 installing aes driver win xp / win xpe aes place the driver cd-rom into your cd-rom drive and follow the steps below to install. 1. Click on start button. 2. Click on settings button. 3. Click on control panel bu...

  • Page 55

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 4 driver installation 4 - 6 4.5 installing pci to isa bridge driver (for rev.A only) win xp / win xpe system place the driver cd-rom into your cd-rom drive and follow the following steps to install. 1. Click on start button. 2. Click on setting...

  • Page 56

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 4 driver installation 4 - 7 4.6 installing ethernet driver 1. Click on the step 4 – lan folder. 2. Double click onthe setupfilelocated in the folder. 3. Follow the instructions that the window shows. 4. The system will help you install the driv...

  • Page 57

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 4 driver installation 4 - 8 information. 4. After you have made your selections and the configuration is what you want, press . A prompt will appear asking if you want to save the configuration. Press "y" if you want to save. There are three ve...

  • Page 58

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 chapter 4 driver installation 4 - 9 8. Click on next. 9. Select search for a suitable driver…, then click on next. 10. Select specify a location, then click on next. 11. Click on browse. 12. Select “lxwdmau” file from cd-rom (drivers/step 5 – audio) th...

  • Page 59: Programming The

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix a programming the watchdog timer a - 1 programming the appendix a watchdog timer.

  • Page 60

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix a programming the watchdog timer a - 2 a.1 programming gene-5315 utilizes ite 8712 chipset as its watchdog timer controller. ( k version ) below are the procedures to complete its configuration and the aaeon intial watchdog timer program is al...

  • Page 61

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix a programming the watchdog timer a - 3 there are three steps to complete the configuration setup: (1) enter the mb pnp mode; (2) modify the data of configuration registers; (3) exit the mb pnp mode. Undesired result may occur if the mb pnp mod...

  • Page 62

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix a programming the watchdog timer a - 4 configure control (index=02h) this register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them. B...

  • Page 63

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix a programming the watchdog timer a - 5 4 wdt output through pwrok1/pwrok2 (pulse) enable 3 select the interrupt level note for wdt watchdog timer time-out value (lsb) register (index=73h, default=00h) bit description 7-0 wdt time-out value 7-0...

  • Page 64

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix a programming the watchdog timer a - 6 watch_dog_setting: ;timer setting mov al, cl mov cl, 73h call superio_set_reg ;clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call superio_set_reg ;unit is second. Mov al, 0c0h mov cl, 72h ...

  • Page 65

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix a programming the watchdog timer a - 7 mov dx,02eh mov cx,04h init_1: mov al,byte ptr cs:[si] out dx,al inc si loop init_1 ret enter_configuration_mode endp exit_configuration_mode proc near mov ax,0202h call write_configuration_data ret exit_...

  • Page 66

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix a programming the watchdog timer a - 8 cmp al,12h jne not_initial need_initial: stc ret not_initial: clc ret check_chip endp read_configuration_data proc near mov dx,word ptr cs:[cfg_port+04h] out dx,al mov dx,word ptr cs:[cfg_port+06h] in al,...

  • Page 67

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix a programming the watchdog timer a - 9 write_configuration_data endp superio_set_reg proc near push ax mov dx,word ptr cs:[cfg_port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret superio_set_reg endp.Set_logic_device proc near set_logic_...

  • Page 68

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix a programming the watchdog timer a - 10 cfg_port db 087h,001h,055h,055h dw 02eh,02fh end main note: interrupt level mapping 0fh-dh: not valid 0ch: irq12 . . 03h: irq3 02h: not valid 01h: irq1 00h: no interrupt selected.

  • Page 69: I/o Information

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix b i/o information b - 1 i/o information appendix b.

  • Page 70

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix b i/o information b - 2 b.1 i/o address map address description user address 000-01f dma controller #1 000-000f 020-03f interrupt controller #1, master 020-021 040-05f system time 040-043 060-06f 8042 (keyboard controller) 060-064 070-07f real...

  • Page 71

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix b i/o information b - 3 b.3 irq mapping chart for rev.A irq0 system timer irq8 system cmos / real time clock irq1 keyboard irq9 microsoft acpi – compliant system irq2 cascade to irq controller irq10 unused irq3 com2 irq11 unused irq4 com1 irq1...

  • Page 72: Mating Connector

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix c mating connector c - 1 mating connector appendix c.

  • Page 73

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix c mating connector c - 2 c.1 list of mating connectors and cables the table notes mating connectors and available cables. Mating connector connector label function vendor model no available cable cable p/n cn1 ide connector molex 87568-4463 id...

  • Page 74

    S u b c o m p a c t b o a r d g e n e - 5 3 1 5 appendix c mating connector c - 3 cn14 system fan connector hobase technology 2503-h-3 n/a cn15 ethernet connector neltron 7001-8p8c n/a cn16 ethernet connector neltron 7001-8p8c n/a cn17 irda connector neltron 2026a-06 n/a cn18 mini-din ps/2 connector...