1. DL manuals
  2. Aaeon
  3. Motherboard
  4. GENE-9655
  5. User Manual

Aaeon GENE-9655 User Manual - Quick

Manual is about: SubCompact Board

Summary of GENE-9655

  • Page 1

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 gene-9655 intel ® core tm 2 duo/celeron ® m (65nm) processors intel ® 82574l for 10/100/1000mbps type ii compactflash tm 4 com, 6 usb2.0, digital i/o mini pci/ mini card gene-9655 manual rev.A 2nd ed. June 2010

  • Page 2

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 i copyright notice this document is copyrighted, 2010. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reprodu...

  • Page 3

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 ii acknowledgments all other products’ name or trademarks are properties of their respective owners. Z award is a trademark of award software international, inc. Z compactflash™ is a trademark of the compact flash association. Z intel ® , core™ 2 duo, ...

  • Page 4

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 iii packing list before you begin installing your card, please make sure that the following materials have been shipped: • 1700060157 keyboard & mouse cable • 1654929900 dvi-i to vga adapter • 9657666600 jumper cap • cooler • quick installation guide •...

  • Page 5

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 iv contents chapter 1 general information 1.1 introduction................................................................ 1-2 1.2 features .................................................................... 1-3 1.3 specifications .......................

  • Page 6

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 v 2.17 digital i/o connector (cn9) .................................... 2-14 2.18 fan connector (cn10) ............................................ 2-15 2.19 com1 rs-232 serial port connector (cn11) ........ 2-15 2.20 com2 rs-232/422/485 serial port co...

  • Page 7

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 vi chapter 4 driver installation 4.1 installation ................................................................. 4-3 appendix a programming the watchdog timer a.1 programming .........................................................A-2 a.2 ite8781 w...

  • Page 8: General

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 1 general information 1- 1 general chapter 1 information.

  • Page 9

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 1.1 introduction aaeon, a leading embedded boards manufacturer, is pleased to announce the debut of their new generation 3.5” subcompact board—gene-9655. The gene-9655 is a cutting-edge product that provides high performance and low power consumption i...

  • Page 10

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 1.2 features z intel ® core™ 2 duo/ celeron ® m (65nm) processors up to 2.2 ghz z intel ® gme965 + ich8m z sodimm ddrii 533/667, max. 2 gb z gigabit ethernet x 2 z dvi-i or crt (optional), 24-bit dual-channel lvds lcd z 2ch audio z sata ii x 1, compact...

  • Page 11

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 1.3 specifications system z processor socket 478m or onboard intel ® core™ 2 duo/ celeron ® m (65nm) processors up to 2.2ghz, fsb 533/667/800mhz z system memory 200-pin ddrii sodimm x 1, max. 2gb (ddrii 533/667) z chipset intel ® gme965 + ich8m z i/o c...

  • Page 12: I/o

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 z power consumption intel ® core™ 2 duo t7500 2.2 ghz, ddrii 667 2 gb, 4.12a @ +12v z board size 5.75”(l) x 4”(w) (146mm x 101.6mm) z gross weight 0.88 lb (0.4 kg) z operating temperature 32˚f~ 140˚f (0˚c ~ 60˚c) z storage temperature -40˚f~ 176˚f (-40...

  • Page 13

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 z digital i/o supports 8-bit (programmable) z audio line-in, line-out, mic-in, cd-in chapter 1 general information 1- 6.

  • Page 14: Quick

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-1 quick installation chapter 2 guide notice: the quick installation guide is derived from chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual cd-rom th...

  • Page 15

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-2 2.1 safety precautions always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive...

  • Page 16

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-3 2.2 location of connectors and jumpers component side ba t1 cn 25 cn 10 cn5 cn11 cn22 cn7 cn21 cn24 jp6 cn19 cn 37 cn27 cn12 cn 20 cn 29 cn 3 0 cn 1 8 cn 1 5 cn 9 jp1 cn35 cn4 cn 8 cn9 cn2 cn26 cn 28 cn 3 6 jp3 jp...

  • Page 17

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-4 solder side dimm1 cn13 cfd1 cn1 3.

  • Page 18

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-5 2.3 mechanical drawing component side 0.00 0.00 59.23 61 .0 5 69.43 72.69 77. 81 86.19 8.89 8.89 3.17 84.24 121.18 142.75 7. 94 17.44 21.72 132.84 89.28 98.37 142.82 146.05 101.60 132.84 80.26 89.79 51. 69 70.90 3...

  • Page 19

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-6 solder side 0.00 0. 00 21.74 65.95 25.77 72.14 31 .3 1 31 .71 55 .92 67 .3 8 56. 32 124.97 91 .19 24 .3 8 cn1 3.

  • Page 20: Jumpers

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-7 2.4 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: jumpers label function jp1...

  • Page 21: Connectors

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-8 2.5 list of connectors the board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: connectors label functio...

  • Page 22

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-9 cn27 usb connector cn28 usb connector cn29 usb connector cn30 usb connector cn36 +5v output connector for 2.5” sata hard disk cn37 uim connector for sim bat1 battery connector cfd1 compactflash disk connector mpci...

  • Page 23

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-10 2.6 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often...

  • Page 24

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-11 2.7 clear cmos (jp1) jp1 function 1-2 protected (default) 2-3 clear 2.8 lvds lcd +5v/+3.3v selection (jp2) jp2 function 1-2 +5v 2-3 +3.3v (default) 2.9 lcd backlight +5v/+12v selection (jp3) jp3 function 1-2 +12v...

  • Page 25

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-12 2.12 lcd backlight voltage / pwm control selection (jp7) jp7 function 1-2 voltage control (default) 2-3 pwm control 2.13 vga/ dvi display connector (cn2) pin signal pin signal 1 dvi_tdc2# 2 dvi_tdc2 3 gnd 4 ddccl...

  • Page 26

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-13 c1 red c2 green c3 blue c4 hsync c5 gnd cg gnd 2.14 lvds lcd connector (cn4) note: for vlcd (pin 3, 7, 27), the max rating of each pin is 5v@0.5a pin name pin name 1 l_bklt_en 2 bkl_con 3 vlcd 4 gnd 5 la_clk# 6 l...

  • Page 27

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-14 3 gnd 4 gnd 5 inv_en 2.16 audio connector (cn8) pin signal pin signal 1 mic_l 2 mic_r 3 gndaud 4 cd_gnd 5 lin_l 6 cd_l 7 lin_r 8 cd_gnd 9 gndaud 10 cd_r 11 lout_l 12 lout_r 13 gndaud 14 gndaud 2.17 digital i/o co...

  • Page 28

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-15 port 7 @2a4h pin 7 gpio set 5 / bit 1 u6 pin 10 (gpio 51) port 6 @2a2h pin 6 gpio set 3 / bit 7 u6 pin 11 (gpio 37) port 5 @2a2h pin 5 gpio set 3 / bit 6 u6 pin 12 (gpio 36) port 4 @2a0h pin 4 gpio set 1 / bit 4 ...

  • Page 29

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-16 2.20 com2 rs-232/422/485 serial port connector (cn12) rs-232 mode pin signal pin signal 1 dcdb 2 rxb 3 txb 4 dtrb 5 ground 6 dsrb 7 rtsb 8 ctsb 9 rib / +5 volt. / +12 volt. 10 n.C rs-422 mode pin signal pin signa...

  • Page 30

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-17 3 rxc 4 rtsc 5 txc 6 ctsc 7 dtrc 8 ric 9 gnd 2.22 ps/2 keyboard/mouse connector (cn19) pin signal pin signal 1 kbdat 2 kbclk 3 kb_gnd 4 +5v_dual 5 msdat 6 msclk 2.23 com4 rs-232 serial port connector (cn20) pin s...

  • Page 31

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-18 2.24 +5v standby power output w/pson#/smbus connector (cn24) pin signal 1 smbdat_sby 2 gnd 3 smbclk_sby 4 gnd 5 ps_on# 6 +5v_dual 2.25 power input connector (cn25) pin signal 1 +12v_dual 2 gnd 2.26 front panel (c...

  • Page 32

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-19 3 usbd2+ 4 gnd 5 gnd 2.28 usb connector (cn28) pin signal 1 +5v_dual 2 usbd3- 3 usbd3+ 4 gnd 5 gnd 2.29 usb connector (cn29) pin signal 1 +5v_dual 2 usbd4- 3 usbd4+ 4 gnd 5 gnd 2.30 usb connector (cn30) pin signa...

  • Page 33

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-20 2.31 +5v output connector for 2.5” sata hard disk (cn36) note: the max. Rating is 5v@1a pin signal 1 +5v 2 gnd 2.32 uim connector for sim (cn37) pin signal 1 uim_pwr 2 uim_rst 3 uim_clk 4 gnd 5 uim_vpp 6 uim_dat ...

  • Page 34

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-21 11 gnd 36 +3.3v 12 gnd 37 irq15 13 +3.3v 38 +3.3v 14 gnd 39 csel# 15 gnd 40 n.C 16 gnd 41 sec_iderst# 17 gnd 42 siordy 18 sda2 43 sddreq 19 sda1 44 dack# 20 sda0 45 dasp# 21 sdd0 46 pdiag# 22 sdd1 47 sdd8 23 sdd2...

  • Page 35

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 2 quick installation guide 2-22 below table for china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon main board/ daughter board/ backplane 有毒有害物质或元素 部件名称 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 ...

  • Page 36: Award

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 3 award bios setup 3-1 award chapter 3 bios setup.

  • Page 37

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fata...

  • Page 38

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 3.2 award bios setup awards bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram so that it retains the setup information when the power is turne...

  • Page 39

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 pnp/pci configurations this entry appears if your system supports pnp/pci. Pc health status this menu shows the voltage, temperature and fan speed of the system. Load fail-safe defaults use this menu to load the bios default values for the minimal/stab...

  • Page 40: Driver

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 chapter 4 driver installation 4 -1 driver chapter 4 installation ..

  • Page 41

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 the gene-9655 comes with an autorun cd-rom that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver cd, the driver cd-title will auto start and show the installation guide. If not, please follow t...

  • Page 42

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 4.1 installation: insert the gene-9655 cd-rom into the cd-rom drive. And install the drivers from step 1 to step 5 in order. Step 1 – install inf driver 1. Click on the step 1- ich-8m inffolder and double click on the infinst911_autol.Exe 2. Follow the...

  • Page 43

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 step 4 –install audio driver 1. Click on the step 4- alc888 folder and select the os folder your system is 2. Double click on setup.Exefile located in each os folder 3. Follow the instructions that the window shows 4. The system will help you install t...

  • Page 44: Programming The

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix a programming the watchdog timer a-1 programming the appendix a watchdog timer.

  • Page 45

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix a programming the watchdog timer a-2 a.1 programming gene-9655 utilizes ite 8781 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the aaeon initial watchdog timer program is also attached bas...

  • Page 46

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix a programming the watchdog timer a-3 there are three steps to complete the configuration setup: (1) enter the mb pnp mode; (2) modify the data of configuration registers; (3) exit the mb pnp mode. Undesired result may occur if the mb pnp mode ...

  • Page 47

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix a programming the watchdog timer a-4 watchdog timer configuration registers configure control (index=02h) this register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not ...

  • Page 48

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix a programming the watchdog timer a-5 watch dog timer 1, 2, 3 configuration register (index=72h, 82h, 92h default=001s0000b) watch dog timer 1,2,3 time-out value (lsb) register (index=73h,83h,93h, default=38h) watch dog timer 1,2,3 time-out val...

  • Page 49

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix a programming the watchdog timer a-6 a.2 ite8781 watchdog timer initial program .Model small .Code main: call enter_configuration_mode call check_chip mov cl, 7 call set_logic_device ;time setting mov cl, 10 ; 10 sec dec al watch_dog_setting: ...

  • Page 50

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix a programming the watchdog timer a-7 call superio_set_reg ; game port enable mov cl, 9 call set_logic_device initial_ok: call exit_configuration_mode mov ah,4ch int 21h enter_configuration_mode proc near mov si,word ptr cs:[offset cfg_port] mo...

  • Page 51

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix a programming the watchdog timer a-8 call write_configuration_data ret exit_configuration_mode endp check_chip proc near mov al,20h call read_configuration_data cmp al,87h jne not_initial mov al,21h call read_configuration_data cmp al,81h jne ...

  • Page 52

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix a programming the watchdog timer a-9 out dx,al mov dx,word ptr cs:[cfg_port+06h] in al,dx ret read_configuration_data endp write_configuration_data proc near mov dx,word ptr cs:[cfg_port+04h] out dx,al xchg al,ah mov dx,word ptr cs:[cfg_port+0...

  • Page 53

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix a programming the watchdog timer a-10 set_logic_device proc near push ax push cx xchg al,cl mov cl,07h call superio_set_reg pop cx pop ax ret set_logic_device endp ;select 02eh->index port, 02fh->data port cfg_port db 087h,001h,055h,055h dw 02...

  • Page 54: I/o Information

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix b i/o information b - 1 i/o information appendix b.

  • Page 55

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix b i/o information b - 2 b.1 i/o address map.

  • Page 56

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix b i/o information b - 3 b.2 1 st mb memory address map.

  • Page 57

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix b i/o information b - 4 b.3 irq mapping chart b.4 dma channel assignments.

  • Page 58: Mating Connecotor

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix c mating connector c - 1 mating connecotor appendix c.

  • Page 59

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix c mating connector c - 2 c.1 list of mating connectors and cables the table notes mating connectors and available cables. Mating connector connector label function vendor model no available cable cable p/n cn4 lvds connector hirose df13-30ds- ...

  • Page 60

    S u b c o m p a c t b o a r d g e n e - 9 6 5 5 appendix c mating connector c - 3 cn24 external aux power and ps_on# catch 2418hj-06 atx external 5vsb cable external aux power and ps_on# cn25 +12v vin connector n/a n/a power cable 1702002010 cn27 usb port 1 connector molex 51021-0500 usb wafer cable...