1. DL manuals
  2. Aaeon
  3. Computer Hardware
  4. HSB-800I
  5. User Manual

Aaeon HSB-800I User Manual

Manual is about: AMD LX800 Processor ISA Half-size CPU Card With DDR, Ethernet, CompactFlash & PC/104

Summary of HSB-800I

  • Page 1

    H a l f - s i z e s b c h s b - 8 0 0 i hsb-800i amd lx800 processor isa half-size cpu card with ddr, ethernet, compactflash™ & pc/104 hsb-800i manual rev. A 3rd ed. October 2012.

  • Page 2

    H a l f - s i z e c p u c a r d h s b - 8 0 0 i i copyright notice this document is copyrighted, 2008. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reprodu...

  • Page 3

    H a l f - s i z e c p u c a r d h s b - 8 0 0 i ii acknowledgments all other products’ name or trademarks are properties of their respective owners. Award is a trademark of award software international, inc. Compactflash™ is a trademark of the compact flash association. Amd, the amd arrow logo and c...

  • Page 4

    H a l f - s i z e c p u c a r d h s b - 8 0 0 i iii packing list before you begin installing hsb-800i, please make sure that the following items have been shipped: • 1701340704 flat cable • 1701400453 ata-100 cable • 1700060192 ps/2 keyboard & mouse cable • 1709140302 cable • 1701200301 flat cable •...

  • Page 5

    H a l f - s i z e c p u c a r d h s b - 8 0 0 i iv contents chapter 1 general information 1.1 introduction................................................................ 1-2 1.2 feature ...................................................................... 1-3 1.3 specification .......................

  • Page 6

    H a l f - s i z e c p u c a r d h s b - 8 0 0 i v 2.17 digital i/o (cn1) ...................................................... 2-11 2.18 lpt port connector (lpt1) .................................... 2-12 2.19 usb connector (usb1~3) ...................................... 2-12 2.20 fan connector (cn...

  • Page 7

    H a l f - s i z e c p u c a r d h s b - 8 0 0 i vi b.3 irq mapping chart ................................................B-3 b.4 dma channel assignments ...................................B-3.

  • Page 8: General

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 1 general information 1-1 general chapter 1 information.

  • Page 9

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 1 general information 1-2 1.1 introduction aaeon releases the economic half-size single board computer (sbc) – hsb-800i, which is designed to target the industrial control and automation market. Hsb-800i is based on amd lx800 processor, which features ...

  • Page 10

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 1 general information 1-3 1.2 features amd lx 800 processor onboard 128mb ddr 400 memory integrated 2d/3d graphics accelerator, vga support crt/tft 10/100/1000base-tx ethernet x 1 (10/100 & gbe optional) usb2.0 x 4/ rs-232 x 3, rs-232/422/485 x 1/ para...

  • Page 11: System

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 1 general information 1-4 1.3 specification system processor amd lx800 system memory onboard 128mb ddr 400 memory chipset amd lx800 + cs5536 ethernet pci 10/100mbps or 10/100/1000mbps lan x 1 (optional), rj-45 x 1, realtek 8100c/8110s controller option...

  • Page 12

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 1 general information 1-5 display: supports crt and lcd simultaneous display vga controller amd lx800 memory shared memory up to 16m resolutions 1600x1200 @ 32bpp at 100mhz for crt; 1600x1200 @ 24bpp for lcd lcd interface up to 24-bit, lvds/ttl lcd sup...

  • Page 13: Quick

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 2 quick installation guide 2-1 quick installation chapter 2 guide.

  • Page 14

    H a l f - s i z e s b c h s b - 8 0 0 i 2.1 safety precautions always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself ...

  • Page 15

    H a l f - s i z e s b c h s b - 8 0 0 i 2.2 location of connectors and jumpers component side solder side chapter 2 quick installation guide 2-3.

  • Page 16

    H a l f - s i z e s b c h s b - 8 0 0 i 2.3 mechanical drawing component side chapter 2 quick installation guide 2-4.

  • Page 17

    H a l f - s i z e s b c h s b - 8 0 0 i solder side 0 86. 5 0 72.37 21.68 1 0 6.91 19 .9 4 1 5 7.38 chapter 2 quick installation guide 2-5.

  • Page 18

    H a l f - s i z e s b c h s b - 8 0 0 i 2.4 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: label function jp1 cfd voltage 3.3v/ 5v selection jp2 clear cmos jp3 at/a...

  • Page 19

    H a l f - s i z e s b c h s b - 8 0 0 i ir1 irda connector lpt1 lpt port connector usb1~3 usb connector usb4 usb connector lan1 10/100 or 100/1000 base-tx ethernet connector dimm1 ddrii sodimm slot (optional) cn1 digital i/o cn2 fan connector cn3 audio input/output/cdin/mic cn4 lcd inverter power co...

  • Page 20

    H a l f - s i z e s b c h s b - 8 0 0 i 2.6 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over ...

  • Page 21

    H a l f - s i z e s b c h s b - 8 0 0 i 2.7 cfd voltage 3.3v/5v selection (jp1) jp1 function 1-2 3.3v (default) 2-3 5v 2.8 clear cmos (jp2) jp2 function 1-2 normal (default) 2-3 clear cmos 2.9 at/atx power type selection (jp3) jp3 function 1-2 atx power supply (default) open at power supply note: on...

  • Page 22

    H a l f - s i z e s b c h s b - 8 0 0 i 2.12 front panel connector (fp1) pin signal pin signal 1 power on button (+) 2 reset switch (+) 3 power on button (-) 4 reset switch (-) 5 ide led (+) 6 power led (+) 7 ide led (-) 8 power led (-) 2.13 front panel connector (fp2) note: internal buzzer enable: ...

  • Page 23

    H a l f - s i z e s b c h s b - 8 0 0 i 2.15 rs-232/422/485 serial port connector (com2) pin signal pin signal 1 dcd (422txd-/485data-) 2 rxd (422rxd+) 3 txd (422txd+/485data+) 4 dtr (422rxd-) 5 gnd 6 dsr 7 rts 8 cts 9 ri 10 nc 2.16 irda connector (ir1) pin signal 1 +5v 2 nc 3 irrx 4 gnd 5 irtx 6 nc...

  • Page 24

    H a l f - s i z e s b c h s b - 8 0 0 i 2.18 lpt port connector (lpt1) pin signal pin signal 1 #strobe 2 #afd 3 data0 4 #error 5 data1 6 #init 7 data2 8 #slin 9 data3 10 gnd 11 data4 12 gnd 13 data5 14 gnd 15 data6 16 gnd 17 data7 18 gnd 19 #ack 20 gnd 21 busy 22 gnd 23 pe 24 gnd 25 select 26 gnd 2....

  • Page 25

    H a l f - s i z e s b c h s b - 8 0 0 i 2.20 fan connector (cn2) pin signal 1 gnd 2 +5v 3 speed sense 2.21 audio input/ output/ cd-in/ mic (cn3) pin signal pin signal 1 mic 2 mic_vcc 3 audio ground 4 cd_gnd 5 line_in l 6 cd_l 7 line_in r 8 cd_gnd 9 audio ground 10 cd_r 11 line_out l 12 line_out r 13...

  • Page 26

    H a l f - s i z e s b c h s b - 8 0 0 i 2.23 tft lcd (cn5) for 24-bit tft lcd pin signal pin signal 1 +5vlcd 2 +5vlcd 3 gnd 4 gnd 5 +3.3vlcd 6 +3.3vlcd 7 bkl_en 8 gnd 9 b0 10 b1 11 b2 12 b3 13 b4 14 b5 15 b6 16 b7 17 g0 18 g1 19 g2 20 g3 21 g4 22 g5 23 g6 24 g7 25 r0 26 r1 27 r2 28 r3 29 r4 30 r5 31...

  • Page 27

    H a l f - s i z e s b c h s b - 8 0 0 i for 18-bit tft lcd pin signal pin signal 1 +5vlcd 2 +5vlcd 3 gnd 4 gnd 5 +3.3vlcd 6 +3.3vlcd 7 bkl_en 8 gnd 9 nc 10 nc 11 b0 12 b1 13 b2 14 b3 15 b4 16 b5 17 nc 18 nc 19 g0 20 g1 21 g2 22 g3 23 g4 24 g5 25 nc 26 nc 27 r0 28 r1 29 r2 30 r3 31 r4 32 r5 33 gnd 34...

  • Page 28

    H a l f - s i z e s b c h s b - 8 0 0 i 2.24 +5vsb power connector (cn6) pin signal 1 ps_on# 2 +5v 3 +5vsb 2.25 at power_5v, 12v connector (cn7) pin signal 1 +5v 2 gnd 3 gnd 4 +12v 2.26 lvds1, 2 (cn9, cn10) pin signal pin signal 1 bkl_en 2 nc 3 vlcd 4 gnd 5 lvds_clk# 6 lvds_clk 7 vlcd 8 gnd 9 tx0# 1...

  • Page 29

    H a l f - s i z e s b c h s b - 8 0 0 i 23 nc 24 nc 25 nc 26 nc 27 vlcd 28 gnd 29 nc 30 nc 2.27 ps2 keyboard/ mouse connector (cn11) pin signal 1 kb_data 2 ms-data 3 gnd 4 +5v 5 kb_clk 6 ms_clk 2.28 internal keyboard connector (cn12) pin signal 1 kb_clk 2 kb_data 3 nc 4 gnd 5 +5v chapter 2 quick ins...

  • Page 30

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 2 quick installation guide 2-18 below table for china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon main board/ daughter board/ backplane 有毒有害物质或元素 部件名称 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 × ○ ○ ○ ...

  • Page 31: Award

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 3 award bios setup 3-1 chapter award 3 bios setup.

  • Page 32

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 3 award bios setup 3-2 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are tw...

  • Page 33: Entering Setup

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 3 award bios setup 3-3 3.2 award bios setup awards bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram so that it retains the setup information ...

  • Page 34: Pc Health Status

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 3 award bios setup 3-4 pc health status this menu shows you the status of pc. Frequency/voltage control this menu shows you the display of frequency/voltage control. Load fail-safe defaults use this menu to load the bios default values for the minimal/...

  • Page 35: Driver

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 4 driver installation 4-1 chapter driver 4 installation.

  • Page 36

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 4 driver installation 4-2 the hsb-800i comes with a cd-rom that contains all drivers your need. Follow the sequence below to install the drivers: step 1 – install lx-graphics driver step 2 – install aes driver step 3 – install pci to isa bridge driver ...

  • Page 37

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 4 driver installation 4-3 4.1 installation: insert the hsb-800i cd-rom into the cd-rom drive. And install the drivers from step 1 to step 5 in order. Step 1 –install lx-graphic driver place the driver cd-rom into your cd-rom drive and follow the steps ...

  • Page 38

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 4 driver installation 4-4 step 2 –install aes driver place the driver cd-rom into your cd-rom drive and follow the steps below to install. 1. Click on start button 2. Click on settings button 3. Click on control panel button 4. Click on system button 5...

  • Page 39

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 4 driver installation 4-5 3. Click on control panel button 4. Click on system button 5. Select hardware and click on device manager… 6. Double click on other pci bridge device 7. Click on update driver… 8. Click on next 9. Select search for a suitable ...

  • Page 40

    H a l f - s i z e s b c h s b - 8 0 0 i chapter 4 driver installation 4-6 step 5– install audio driver place the driver cd-rom into your cd-rom drive and follow the steps below to install. 1. Click on start button 2. Click on settings button 3. Click on control panel button 4. Click on system button...

  • Page 41: Programming The

    H a l f - s i z e s b c h s b - 8 0 0 i appendix a programming the watchdog timer a - 1 programming the appendix a watchdog timer.

  • Page 42

    H a l f - s i z e s b c h s b - 8 0 0 i appendix a programming the watchdog timer a - 2 a.1 programming hsb-800i utilizes ite 8712 chipset as its watchdog timer controller. ( k version ) below are the procedures to complete its configuration and the aaeon intial watchdog timer program is also attach...

  • Page 43

    H a l f - s i z e s b c h s b - 8 0 0 i appendix a programming the watchdog timer a - 3 there are three steps to complete the configuration setup: (1) enter the mb pnp mode; (2) modify the data of configuration registers; (3) exit the mb pnp mode. Undesired result may occur if the mb pnp mode is not...

  • Page 44

    H a l f - s i z e s b c h s b - 8 0 0 i appendix a programming the watchdog timer a - 4 configure control (index=02h) this register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them. Bit descr...

  • Page 45

    H a l f - s i z e s b c h s b - 8 0 0 i appendix a programming the watchdog timer a - 5 4 wdt output through pwrok1/pwrok2 (pulse) enable 3 select the interrupt level note for wdt watchdog timer time-out value (lsb) register (index=73h, default=00h) bit description 7-0 wdt time-out value 7-0 watchdo...

  • Page 46

    H a l f - s i z e s b c h s b - 8 0 0 i appendix a programming the watchdog timer a - 6 watch_dog_setting: ;timer setting mov al, cl mov cl, 73h call superio_set_reg ;clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call superio_set_reg ;unit is second. Mov al, 0c0h mov cl, 72h call sup...

  • Page 47

    H a l f - s i z e s b c h s b - 8 0 0 i appendix a programming the watchdog timer a - 7 mov dx,02eh mov cx,04h init_1: mov al,byte ptr cs:[si] out dx,al inc si loop init_1 ret enter_configuration_mode endp exit_configuration_mode proc near mov ax,0202h call write_configuration_data ret exit_configur...

  • Page 48

    H a l f - s i z e s b c h s b - 8 0 0 i appendix a programming the watchdog timer a - 8 cmp al,12h jne not_initial need_initial: stc ret not_initial: clc ret check_chip endp read_configuration_data proc near mov dx,word ptr cs:[cfg_port+04h] out dx,al mov dx,word ptr cs:[cfg_port+06h] in al,dx ret r...

  • Page 49

    H a l f - s i z e s b c h s b - 8 0 0 i appendix a programming the watchdog timer a - 9 write_configuration_data endp superio_set_reg proc near push ax mov dx,word ptr cs:[cfg_port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret superio_set_reg endp.Set_logic_device proc near set_logic_device p...

  • Page 50

    H a l f - s i z e s b c h s b - 8 0 0 i appendix a programming the watchdog timer a - 10 cfg_port db 087h,001h,055h,055h dw 02eh,02fh end main note: interrupt level mapping 0fh-dh: not valid 0ch: irq12 . . 03h: irq3 02h: not valid 01h: irq1 00h: no interrupt selected.

  • Page 51: I/o Information

    H a l f - s i z e s b c h s b - 8 0 0 i appendix b i/o information b-1 i/o information appendix b.

  • Page 52

    H a l f - s i z e s b c h s b - 8 0 0 i appendix b i/o information b-2 b.1 i/o address map.

  • Page 53

    H a l f - s i z e s b c h s b - 8 0 0 i appendix b i/o information b-3 b.2 memory address map b.3 irq mapping chart b.4 dma channel assignments.