1. DL manuals
  2. Aaeon
  3. PCI Card
  4. HSB-811P
  5. Manual

Aaeon HSB-811P Manual

Manual is about: Half-size CPU Card Onboard Intel Celeron M 600/ non-cache Processors Half-size CPU Card With DDR, Ethernet, CompactFlashTM & Mini PCI

Summary of HSB-811P

  • Page 1

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p hsb-811p onboard intel ® celeron ® m 600/ non-cache processors half-size cpu card with ddr, ethernet, compactflash™ & mini pci hsb-811p manual rev. A 2nd ed. May 2009.

  • Page 2

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p i copyright notice this document is copyrighted, 2009. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reprodu...

  • Page 3

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p ii acknowledgments all other products’ name or trademarks are properties of their respective owners. Award is a trademark of award software international, inc. Compactflash™ is a trademark of the compact flash association. Intel ® pentium ® m, and cele...

  • Page 4

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p iii packing list before you begin installing hsb-811p, please make sure that the following items have been shipped: • 1 hsb-811p cpu card • 1 floppy cable • 1 ata-100 cable • 1 usb cable • 1 ps/2 keyboard & mouse cable • 1 serial + parallel cable • 1 s...

  • Page 5

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p iv contents chapter 1 general information 1.1 introduction................................................................ 1-2 1.2 feature ...................................................................... 1-4 1.3 specification .......................

  • Page 6

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p v 2.18 ac97 connector (cn2) ........................................... 2-12 2.19 lvds channel connector (cn3) ............................ 2-13 2.20 ps/2 keyboard & mouse connector (cn4) ............. 2-14 2.21 internal keyboard connector (cn5)..........

  • Page 7: General

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 1 general information 1-1 general chapter 1 information.

  • Page 8

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 1 general information 1-2 1.1 introduction introducing aaeon’s new hsb-811p, powered by intel ® celeron ® m 600/non-cache processor on board, mini pci half-size form factor single board computer (sbc) with an onboard vga, 10/100/1000mb lan opti...

  • Page 9

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 1 general information 1-3 dram (ddr 266) and support ultra ata100 & compactflash™ type ii storage. In addition to its powerful computing engine, one mini pci socket type iii provides flexible application on wireless lan, blue tooth…etc. Five us...

  • Page 10

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 1 general information 1-4 1.2 feature • onboard intel ® celeron ® m 600/non-cache cpu • ddr266 memory supports up to 2gb • integrated agp 4x 2d/3d graphics accelerator, lvds support • integrated ac97 codec audio (daughter board optional) • supp...

  • Page 11: System

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 1 general information 1-5 1.3 specification system cpu: support onboard intel ® celeron ® m 600/non-cache cpu chipset: intel ® 82852gm+82801db (ich4) i/o chipset: intel ® 82801db(ich4)+ite 8712f/hx ethernet: 10/100mb or 10/100/1000mb lan option...

  • Page 12

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 1 general information 1-6 mini-pci type iii socket battery: lithium battery (br2335) power supply voltage: +12v atx, standard atx power connector vga controller: integrated on intel ® 82852gm, agp 4x, supports dual display lcd controller: integ...

  • Page 13: Display

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 1 general information 1-7 display chip: intel ® 82852gm memory size: shared memory up to 64mb i/o enhanced ide interface：ata100 x 2 channels (supports two atapi devices for each channel) fdd interface: standard fdd port x 1 (support up to 2 flo...

  • Page 14: Os Support Request

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 1 general information 1-8 os support request windows ® 98se windows ® 2000 pro windows ® xp pro linux red hat windows ® ce.Net (by demand) windows ® xp embedded (by demand).

  • Page 15: Quick

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-1 quick installation chapter 2 guide notice: the quick installation guide is derived from chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual cd-rom th...

  • Page 16

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-2 2.1 safety precaution always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive ...

  • Page 17

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-3 2.2 location of connectors and jumpers component side vga1 ide1 ide2 usb1 usb2 usb3 lan1 cn4 u sb4 com 2 co m 1 lpt1 fp2 fp1 fdd 1 atx2 atx1 cn1 fan 1 jp2 cn 3 cn2 ir1 cn6 cn 5 mp ci 1 jp1.

  • Page 18

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-4 solder side cfd1 dimm0 dimm1.

  • Page 19

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-5 2.3 mechanical drawings component side 1 1 8 .0 1 3 .9 9 3.99 177.98 3.02 4 .0 1 9 8 .5 1 9 .4 8 16.51 184.99 1 2 2 4 .4 5 0 .5 1 12.27 30.48 13.84 9.32 1.6 14.5 6.5 13.4 6.27 12.55 14.1 9 .3 7 2 7 .6 9 5 2 .9 2 7...

  • Page 20

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-6 solder side 184.99 16.51 9 8 .5 4 .0 1 3.02 177.98 3.99 3 .9 9 1 1 8 .0 1 1 2 2 4 .4 5 12.27 30.48 13.84 9.32.

  • Page 21: Jumpers

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-7 2.4 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: jumpers label function jp1...

  • Page 22

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-8 ir1 irda connector lpt1 lpt port connector usb1~3 usb connector (type-a) usb4 usb connector (5x2 pin header) lan1 10/100 or 100/1000 base-tx ethernet connector mpci1 mini pci slot dimm0~1 dimm slot fan1 fan connec...

  • Page 23

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-9 2.6 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often ...

  • Page 24

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-10 2.7 clear cmos (jp1) jp1 function close clear open protected (default) 2.8 lcd voltage selection (jp2) jp2 function 1-2 +5v 2-3 +3.3 v (default) 2.9 front panel connector (fp1) pin signal pin signal 1 power on bu...

  • Page 25

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-11 3 txd 4 dtr 5 gnd 6 dsr 7 rts 8 cts 9 ri 10 n.C. 2.12 rs-232/422/485 serial port connector (com2) pin signal pin signal 1 dcd (422txd-/485data-) 2 rxd (422rxd+) 3 txd (422txd+/485data+) 4 dtr (422rxd-) 5 gnd 6 ds...

  • Page 26

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-12 9 data3 10 gnd 11 data4 12 gnd 13 data5 14 gnd 15 data6 16 gnd 17 data7 18 gnd 19 #ack 20 gnd 21 busy 22 gnd 23 pe 24 gnd 25 select 26 n.C. 2.15 usb connector (usb4) pin signal pin signal 1 +5v 2 gnd 3 usbd1- 4 g...

  • Page 27

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-13 3 5vsb 2.18 ac97 connector (cn2) pin signal pin signal 1 ac_rst- 2 ac_sync 3 ac_dain2 4 ac_daout 5 gnd 6 ac_bclk 7 gnd 8 +5v 9 lock 10 +3.3v 2.19 lvds channel connector (cn3) pin signal pin signal 1 bklen 2 bklct...

  • Page 28

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-14 2.20 ps/2 keyboard & mouse connector (cn4) pin signal 1 kb_data 2 ms_data 3 gnd 4 +5v 5 kb_clk 6 ms_clk 2.21 internal keyboard connector (cn5) pin signal 1 kb_clk 2 kb_data 3 n.C. 4 gnd 5 +5v 2.22 lan led connect...

  • Page 29

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 2 quick installation guide 2-15 below table for china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon main board/ daughter board/ backplane 有毒有害物质或元素 部件名称 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 ...

  • Page 30: Award

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 3 award bios setup 3-1 chapter award 3 bios setup.

  • Page 31

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter3 award bios setup 3 - 2 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. The...

  • Page 32: Entering Setup

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter3 award bios setup 3 - 3 3.2 award bios setup awards bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in cmos ram so that it retains the setup information when t...

  • Page 33: Pc Health Status

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter3 award bios setup 3 - 4 pc health status this menu shows you the status of pc. Frequency/voltage control this menu shows you the display of frequency/voltage control. Load fail-safe defaults use this menu to load the bios defaults for the minim...

  • Page 34: Driver

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 4 driver installation 4-1 chapter driver 4 installation.

  • Page 35

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 4 driver installation 4-2 the hsb-811p comes with a cd-rom that contains all drivers your need. Follow the sequence below to install the drivers: step 1 – intel ® chipset software installation utility step 2 – intel ® extreme graphics driver st...

  • Page 36

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 4 driver installation 4-3 4.1 installation: insert the hsb-811p cd-rom into the cd-rom drive. And install the drivers from step 1 to step 4 in order. Step 1 - intel ® chipset software installation utility 1. Click on the intel ® chipset softwar...

  • Page 37

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 4 driver installation 4-4 system 3. Select device manager under the hardware category. 4. Double click on the ethernet controller and select reinstall driver button under the general category. 5. Click next twice and tick the specify a location...

  • Page 38

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p chapter 4 driver installation 4-5 1. Click on the usb to cf controller driver for win9x folder. 2. Follow the instructions that the window shows. 3. The system will help you install the driver automatically..

  • Page 39: Programming The

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix a programming the watchdog timer a-1 programming the appendix a watchdog timer.

  • Page 40

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix a programming the watchdog timer a-2 a.1 programming hsb-811p utilizes ite 8712 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the aaeon intial watchdog timer program is also attached based...

  • Page 41

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix a programming the watchdog timer a-3 there are three steps to complete the configuration setup: (1) enter the mb pnp mode; (2) modify the data of configuration registers; (3) exit the mb pnp mode. Undesired result may occur if the mb pnp mode ...

  • Page 42

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix a programming the watchdog timer a-4 configure control (index=02h) this register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them..

  • Page 43

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix a programming the watchdog timer a-5 watchdog timer control register (index=71h, default=00h) watchdog timer configuration register (index=72h, default=00h) watchdog timer time-out value register (index=73h, default=00h).

  • Page 44

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix a programming the watchdog timer a-6 b.2 ite8712f/hx watchdog timer initial program .Model small .Code main: call enter_configuration_mode call check_chip mov cl, 7 call set_logic_device ;time setting mov cl, 10 ; 10 sec dec al watch_dog_setti...

  • Page 45

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix a programming the watchdog timer a-7 ; game port enable mov cl, 9 call set_logic_device initial_ok: call exit_configuration_mode mov ah,4ch int 21h enter_configuration_mode proc near mov si,word ptr cs:[offset cfg_port] mov dx,02eh mov cx,04h ...

  • Page 46

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix a programming the watchdog timer a-8 ret exit_configuration_mode endp check_chip proc near mov al,20h call read_configuration_data cmp al,87h jne not_initial mov al,21h call read_configuration_data cmp al,12h jne not_initial need_initial: stc ...

  • Page 47

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix a programming the watchdog timer a-9 mov dx,word ptr cs:[cfg_port+06h] in al,dx ret read_configuration_data endp write_configuration_data proc near mov dx,word ptr cs:[cfg_port+04h] out dx,al xchg al,ah mov dx,word ptr cs:[cfg_port+06h] out dx...

  • Page 48

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix a programming the watchdog timer a-10 push ax push cx xchg al,cl mov cl,07h call superio_set_reg pop cx pop ax ret set_logic_device endp ;select 02eh->index port, 02fh->data port cfg_port db 087h,001h,055h,055h dw 02eh,02fh end main note: inte...

  • Page 49: I/o Information

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix b i/o information b - 1 i/o information appendix b.

  • Page 50

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix b i/o information b-2 b.1 i/o address map.

  • Page 51

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix b i/o information b-3 b.2 memory address map.

  • Page 52

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix b i/o information b-4 b.3 irq mapping chart b.4 dma channel assignments.

  • Page 53: Mating Connector

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix c mating connector c - 1 mating connector appendix c.

  • Page 54

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix c mating connector c - 2 c.1 list of mating connectors and cables the table notes mating connectors and available cables. Mating connector connector label function vendor model no available cable cable p/n ide1 ide connector catch electronics ...

  • Page 55

    H a l f - s i z e c p u c a r d h s b - 8 1 1 p appendix c mating connector c - 3 connector ir1 irda connector jih vei electronics 21b12050-xxs 10b-01g-4/2.8 n/a cfd1 compact flash header speed tech 1. N003 @ 0011-100 2. N016@014 0-104+n01 p4011-009 9 n/a cn1 ps_on connect catch electronics 1191-700...