1. DL manuals
  2. Aaeon
  3. Motherboard
  4. HSB-910I
  5. User Manual

Aaeon HSB-910I User Manual

Manual is about: Half-size SBC

Summary of HSB-910I

  • Page 1

    H a l f - s i z e s b c h s b - 9 1 0 i hsb-910i intel ® celeron ® m processor isa expansion half-size sbc two 200-pin ddrii 400 sodimm 2 sata i/ 1 ide/ 1 fdd/ 1 compactflash 5 usb 2.0/ 4 com/ 1 irda hsb-910 manual rev.A 1st ed. January 2009.

  • Page 2

    H a l f - s i z e s b c h s b - 9 1 0 i i copyright notice this document is copyrighted, 2009. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, cop...

  • Page 3

    H a l f - s i z e s b c h s b - 9 1 0 i ii acknowledgments all other products’ name or trademarks are properties of their respective owners. Award is a trademark of award software international, inc. Compactflash™ is a trademark of the compact flash association. Intel ® , and celeron ® m are tradema...

  • Page 4

    H a l f - s i z e s b c h s b - 9 1 0 i iii packing list before you begin installing your card, please make sure that the following materials have been shipped: • 1 hsb-910i cpu card • 1 floppy cable • 1 ata100 cable • 1 usb cable • 1 keyboard & mouse cable • 1 atx cable • 1 serial + parallel cable ...

  • Page 5

    H a l f - s i z e s b c h s b - 9 1 0 i iv contents chapter 1 general information 1.1 introduction................................................................ 1-2 1.2 features .................................................................... 1-3 1.3 specifications ...............................

  • Page 6

    H a l f - s i z e s b c h s b - 9 1 0 i v 2.18 digital i/o (cn1) ...................................................... 2-12 2.19 lan led connector (cn2, cn5)............................ 2-13 2.20 internal keyboard connector (cn3)........................ 2-13 2.21 ps/2 keyboard/ mouse connector (cn4...

  • Page 7: General

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 1 general information 1- 1 general chapter 1 information.

  • Page 8

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 1 general information 1- 2 1.1 introduction the hsb-910i utilizes the intel ® 910gmle and ich6m chipset, supporting intel ® celeron ® m 90nm processors with a fsb of 400mhz up to 1.8ghz. Offering two 200-pin ddr ii sodimm sockets, the hsb-910i supports...

  • Page 9

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 1 general information 1- 3 1.2 features intel ® celeron ® m 90nm processor up to 1.8ghz intel ® 910gmle + intel ® ich6m 200-pin ddrii 400 sodimm x 2, up to 2gb gigabit ethernet x 2 or x 1 (optional) integrated intel ® enhance graphics core, vga support...

  • Page 10

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 1 general information 1- 4 1.3 specifications system cpu intel ® celeron ® m 90nm processor up to 1.8ghz, fsb 400mhz (bga/ socket co-lay) system memory two ddrii sodimm, support ddrii 400 up to 2gb chipset intel ® 910gmle + intel ® ich6m ethernet lan1/...

  • Page 11

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 1 general information 1- 5 (typical) emc ce/fcc class a display vga chipset enhanced integrated graphics memory shared memory up to 256m resolutions up to 2048 x 1536 @ 32bpp for crt; 1920 x 1200 @ 18bpp for lcd i/o storage sata i x 2, ide x 1, compact...

  • Page 12: Quick

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 1 quick installation chapter 2 guide notice: the quick installation guide is derived from chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual cd-rom that cam...

  • Page 13

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 2 2.1 safety precautions always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive elect...

  • Page 14

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 3 2.2 location of connectors and jumpers component side solder side.

  • Page 15

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 4 2.3 mechanical drawing component side.

  • Page 16

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 5 solder side.

  • Page 17: Jumpers

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 6 2.4 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: jumpers label function jp1 clear...

  • Page 18

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 7 2.5 list of connectors the board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: connectors label function fp1 ...

  • Page 19

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 8 dimm1、2 ddrii memory slot cn1 digital i/o cn2 lan1 active led connector cn3 ps/2 keyboard/mouse connector cn4 internal keyboard connector cn5 lan2 active led connector cn6 3-pin fan connector cn7 lvds channel connector ...

  • Page 20

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 9 2.6 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protec...

  • Page 21

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 10 2.7 clear cmos (jp1) jp1 function 1-2 protected (default) 2-3 clear 2.8 cf voltage selection (jp2) jp2 function 1-2 +3.3v (default) 2-3 +5v 2.9 lvds voltage selection (jp4) jp4 function 1-2 +5v 2-3 +3.3v (default) 2.10...

  • Page 22

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 11 2.12 battery connector (bt1) pin signal pin signal 1 vbat(+) 2 gnd(-) 2.13 rs-232 serial port connector (com1, com3, com4) pin signal pin signal 1 dcd 2 rxd 3 txd 4 dtr 5 gnd 6 dsr 7 rts 8 cts 9 ri 10 n.C. 2.14 rs-232/...

  • Page 23

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 12 2.16 lpt port connector (lpt1) pin signal pin signal 1 #strobe 2 #afd 3 data0 4 #error 5 data1 6 #init 7 data2 8 #slin 9 data3 10 gnd 11 data4 12 gnd 13 data5 14 gnd 15 data6 16 gnd 17 data7 18 gnd 19 #ack 20 gnd 21 bu...

  • Page 24

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 13 7 dio1-7 8 dio1-8 2.19 lan led connector (cn2, cn5) pin signal pin signal 1 active_led(-) 2 active_led(+) 2.20 internal keyboard connector (cn3) pin signal 1 kb_clk 2 kb_data 3 n.C. 4 gnd 5 +5v 2.21 ps/2 keyboard/ mous...

  • Page 25

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 14 2.23 lvds channel connector (cn7) pin signal pin signal 1 bklen 2 bklctl 3 ppvcc 4 gnd 5 ch1_clk# 6 ch1_clk 7 ppvcc 8 gnd 9 ch1_tx0# 10 ch1_tx0 11 ch1_tx1# 12 ch1_tx1 13 ch1_tx2# 14 ch1_tx2 15 n.C. 16 n.C. 17 i2c_data ...

  • Page 26

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 2 quick installation guide 2 - 15 below table for china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon main board/ daughter board/ backplane 有毒有害物质或元素 部件名称 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 × ○ ○ ...

  • Page 27: Award

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 3 award bios setup 3-1 chapter award 3 bios setup.

  • Page 28

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 3 award bios setup 3-2 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are tw...

  • Page 29: Entering Setup

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 3 award bios setup 3-3 3.2 award bios setup awards bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram so that it retains the setup information ...

  • Page 30: Pc Health Status

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 3 award bios setup 3-4 pc health status this menu allows you to set the shutdown temperature for your system. Load fail-safe defaults use this menu to load the bios default values for the minimal/stable performance for your system to operate. Load opti...

  • Page 31: Driver

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 4 driver installation 4-1 chapter driver 4 installation.

  • Page 32

    H a l f - s i z e s b c h s b - 9 1 0 i chapter 4 driver installation 4-2 the hsb-910i comes with a cd-rom that contains all drivers your need. Follow the sequence below to install the drivers: step 1 – install inf driver step 2 – install vga driver step 3 – install lan driver please read following ...

  • Page 33

    H a l f - s i z e s b c h s b - 9 1 0 i chapter4 drivers installation 4-3 4.1 installation: insert the hsb-910i cd-rom into the cd-rom drive. And install the drivers from step 1 to step 3 in order. Step 1 – install inf driver 1. Click on the step 1-ich6-m inf folder and then double click on the infi...

  • Page 34: Programming The

    H a l f - s i z e s b c h s b - 9 1 0 i appendix a programming the watchdog timer a-1 programming the appendix a watchdog timer.

  • Page 35

    H a l f - s i z e s b c h s b - 9 1 0 i appendix a programming the watchdog timer a-2 a.1 programming hsb-910i utilizes ite 8712 chipset as its watchdog timer controller. ( k version ) below are the procedures to complete its configuration and the aaeon intial watchdog timer program is also attached...

  • Page 36

    H a l f - s i z e s b c h s b - 9 1 0 i appendix a programming the watchdog timer a-3 (1) enter the mb pnp mode to enter the mb pnp mode, four special i/o write operations are to be performed during wait for key state. To ensure the initial state of the key-check logic, it is necessary to perform fo...

  • Page 37

    H a l f - s i z e s b c h s b - 9 1 0 i appendix a programming the watchdog timer a-4 bit description 7-2 reserved 1 returns to the wait for key state. This bit is used when the configuration sequence is completed. 0 resets all logical devices and restores configuration registers to their power-on s...

  • Page 38

    H a l f - s i z e s b c h s b - 9 1 0 i appendix a programming the watchdog timer a-5 watchdog timer time-out value (lsb) register (index=73h, default=00h) bit description 7-0 wdt time-out value 7-0 watchdog timer time-out value (msb) register (index=74h, default=00h) bit description 7-0 wdt time-ou...

  • Page 39

    H a l f - s i z e s b c h s b - 9 1 0 i appendix a programming the watchdog timer a-6 mov cl, 73h call superio_set_reg ;clear by keyboard or mouse interrupt mov al, 0f0h mov cl, 71h call superio_set_reg ;unit is second. Mov al, 0c0h mov cl, 72h call superio_set_reg ; game port enable mov cl, 9 call ...

  • Page 40

    H a l f - s i z e s b c h s b - 9 1 0 i appendix a programming the watchdog timer a-7 mov al,byte ptr cs:[si] out dx,al inc si loop init_1 ret enter_configuration_mode endp exit_configuration_mode proc near mov ax,0202h call write_configuration_data ret exit_configuration_mode endp check_chip proc n...

  • Page 41

    H a l f - s i z e s b c h s b - 9 1 0 i appendix a programming the watchdog timer a-8 need_initial: stc ret not_initial: clc ret check_chip endp read_configuration_data proc near mov dx,word ptr cs:[cfg_port+04h] out dx,al mov dx,word ptr cs:[cfg_port+06h] in al,dx ret read_configuration_data endp w...

  • Page 42

    H a l f - s i z e s b c h s b - 9 1 0 i appendix a programming the watchdog timer a-9 push ax mov dx,word ptr cs:[cfg_port+04h] mov al,cl out dx,al pop ax inc dx out dx,al ret superio_set_reg endp.Set_logic_device proc near set_logic_device proc near push ax push cx xchg al,cl mov cl,07h call superi...

  • Page 43

    H a l f - s i z e s b c h s b - 9 1 0 i appendix a programming the watchdog timer a-10 end main note: interrupt level mapping 0fh-dh: not valid 0ch: irq12 . . 03h: irq3 02h: not valid 01h: irq1 00h: no interrupt selected.

  • Page 44: I/o Information

    H a l f - s i z e s b c h s b - 9 1 0 i appendix b i/o information b - 1 i/o information appendix b.

  • Page 45

    H a l f - s i z e s b c h s b - 9 1 0 i appendix b i/o information b-2 b.1 i/o address map.

  • Page 46

    H a l f - s i z e s b c h s b - 9 1 0 i appendix b i/o information b-3 b.2 memory address map.

  • Page 47

    H a l f - s i z e s b c h s b - 9 1 0 i appendix b i/o information b-4 b.3 irq mapping chart b.4 dma channel assignments.

  • Page 48: Mating Connector

    H a l f - s i z e s b c h s b - 9 1 0 i appendix c mating connector c - 1 mating connector x appendi c.

  • Page 49

    H a l f - s i z e s b c h s b - 9 1 0 i appendix c mating connector c - 2 c.1 list of mating connectors and cables the table notes mating connectors and available cables. Mating connector connector label function vendor model no available cable cable p/n ide1 ide connector catch electronics 1137-020...

  • Page 50

    H a l f - s i z e s b c h s b - 9 1 0 i appendix c mating connector c - 3 vga1 crt display connector catch electronics 3125-000-15s b n/a ir1 irda connector jih vei electronics 21b12050-xx s10b-01g-4/2 .8 n/a cn1 digital i/o jih vei electronics n/a cn2 lan 1 active led connector jih vei electronics ...