1 user manual rom ro-1 user manual rev. 1.0.0, may 22 nd 2015 congratulations! You are now the owner of the rom ro-1 reverb pedal! Rom is a high-quality, custom aluminum housing reverb pedal with true bypass. It can be controlled like a stand-alone effects pedal or use the aero tm ae-1 wireless cont...
2 contents 1. Getting started ........................................................................... 3 2. Controls ........................................................................................ 3 3. Overview ................................................................................
3 1. Getting started to get your pedal up and running you need a standard 9v dc, 2.1 mm plug, center negative power supply (minimum 250 ma). You will find the connector at the back of your pedal. The pedal supports both mono and stereo connections. Combinations of these will lead to different proper...
4 o alt (no light): short pre-delay 10 ms o alt (light): long pre-delay on/off set the pedal to on (activated) or off (true bypass)..
5 3. Overview *set active parameter for aero tm ae-1 wireless controller.
6 4. Technical specifications power supply (not included) 9v dc, 2.1 mm plug (center negative) current draw 250 ma input impedance@1khz ~1m ohm output impedance@1khz maximum input signal 3.22 vp-p (2.28 vrms) sound quality (sample-/bit rate) 48 khz/24-bits connectors - input (mono/stereo) - output (...
7 5. Software update update app estimated ready: after summer 2015 performing software updates on your wireless aalberg audio product is easy: 1. To set your device in software update mode: for aero: i. Turn off the aero (slide switch set to ‘0’) ii. Press and hold rotary knob button and preset butt...
8 4. The aalberg audio device set to update mode will now show up in a list in the aalberg updater, and you can check the current revision of the software found on the device. 5. You can now choose if you want to update to the latest software available. 6. A status bar indicates the upload process a...
9 * 6. Wireless control - pairing in order to control your aalberg effects pedal using the aero wireless controller (optional) you need to pair the devices. Below is a step-by-step guide: 1. To set your devices in pairing mode: aero: i. Turn off the aero (slide switch set to ‘0’) ii. Press and hold ...
10 2. Confirm pairing: i. When you have repeated the above steps for all of your aalberg pedals, you need to press and hold the rotary knob button for 3 seconds, then release button. Ii. To indicate that pairing is completed, aero led (red) and lowermost leds in mid row for all pedals will light for...
11 7. Input/output setups the aalberg rom tm ro-1 reverb pedal offers the following mono/stereo configurations: 1. Mono in/mono out 2. Mono in/stereo out 3. Dry/wet split 4. Stereo in/stereo out 1. Mono in/mono out connect your instrument to mono in and the amplifier to mono out. 2. Mono in/stereo o...
12 connecting your instrument to stereo in will split the dry/wet signal as follows: mono out: 100% wet signal stereo out: 100% dry signal 4. Stereo in/stereo out for a more spacious reverb using two amplifiers. Connect stereo signal to both inputs in and one amplifier to mono out and another amplif...
13 8. Disclaimers all use of our products is undertaken at your own risk and expense and aalberg audio cannot be held liable for any direct or indirect losses or cost incurred through use, default or malfunction of our products. Repair or replacement of defective units under our warranty provisions ...
14 product needs to be accompanied by a copy of your receipt, serial number, return address, phone number, e-mail address and a brief explanation of the problem. If the product is altered or repaired by someone unauthorized by aalberg audio the warranty is no longer valid. Stores and distributors mu...
15 10. History the inspiration for the delay pedals with wireless controller came to guitar player and inventor rune aalberg alstad back in 2009, when he was tired of having to run over to the pedals and bend down all the time to change the effect settings. In 2012 he met the engineer torkild indstø...
16 11. Ipr-related design protection pending in eu & usa international patent application pending pct/no2014/050236 12. Compliance aalberg audio accept and follow these regulations and directives..
17 13. About aalberg audio aalberg audio as is located in trondheim, norway. We produce wireless guitar effects with accompanying hardware and software. Please don't hesitate to contact us if you have any questions or inquiries! Visit: www.Aalbergaudio.Com www.Aalbergaudio.Com trondheim norway ™ and...
