1. DL manuals
  2. AAON
  3. Network Hardware
  4. FWS-2350
  5. Manual

AAON FWS-2350 Manual

Manual is about: Desktop Network Appliance Platform CompactFlash Socket 6 LAN Ports 2 USB2.0, 1 COM for Console

Summary of FWS-2350

  • Page 1

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 fws-2350 desktop network appliance platform compactflash™ socket 6 lan ports 2 usb2.0, 1 com for console fws-2350 manual 3rd ed. November, 2014.

  • Page 2

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 i copyright notice this document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduc...

  • Page 3

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 ii acknowledgments all other products ’ name or trademarks are properties of their respective owners.  intel ® and atom™ are trademarks of intel ® corporation.  ami is a trademark of american megatrends inc.  compactflash ™ is a trademark of the comp...

  • Page 4

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 iii caution there is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions and your local gover...

  • Page 5

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 iv packing list before you begin installing your card, please make sure that the following materials have been shipped: fws-2350 cd-rom for manual (in pdf format) and drivers if any of these items should be missing or damaged, please contact your distri...

  • Page 6

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 v contents chapter 1 general information 1.1 introduction .......................................................... 1-2 1.2 features .............................................................. 1-3 1.3 specifications ....................................

  • Page 7: Chapter 3 Ami Bios Setup

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 vi 2.17 hard disk installation ........................................ 2-13 2.18 vga card installation ...................................... 2-19 chapter 3 ami bios setup 3.1 system test and initialization ............................. 3-2 3.2 ami bio...

  • Page 8: General

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 1 general information 1- 1 general information chapter 1.

  • Page 9

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 1 general information 1- 2 1.1 introduction fws-2350 adopts the intel ® dual core atom ™ c2358 1.7 ghz/ quad core atom ™ c2558 2.4 ghz. The system memory features ddr3 long-dimm socket, ecc or non-ecc sdram up to 16gb. It deploys 6x gigabit ethe...

  • Page 10

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 1 general information 1- 3 1.2 features built-in gigabuilt ethernet x 6 dual core intel ® atom ™ c2358 1.7 ghz/ quad core atom™ c2558 2.4 ghz supports quickassist crypto acceleration ddr3 long-dimm socket, supports up to 16gb ecc or non-ecc sdra...

  • Page 11: System

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 1 general information 1- 4 1.3 specifications system form factor desktop 6-ports network appliance processor dual core intel ® atom ™ c2358 1.7 ghz processor quad core intel ® atom ™ c2558 2.4 ghz processor system memory ddr3 long-dimm slot dual...

  • Page 12: Display

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 1 general information 1- 5 2.5” hdd bay x 1 system fan 4 cm ball bearing fan front i/o panel power led x 1, status led x 1, hdd active led x 1, lan led x 12, bypass led x 2 rear i/o panel usb2.0 port x 2, rj-45 x 6, rj-45 console x 1, 12v dc pow...

  • Page 13: Environment

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 1 general information 1- 6 serial port rj-45 console x 1 keyboard & mouse reserved pin header usb usb2.0 type a on i/o side x 2 environment operating temperature 32 o f~104 o f (0 o c ~40 o c) storage temperature -4 o f~104 o f (-20 o c ~60 o c)...

  • Page 14

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 1 general information 1- 7 1.4 general system information.

  • Page 15: Quick

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-1 quick installation guide chapter 2.

  • Page 16

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-2 2.1 safety precautions the installation is intended for technically qualified personnel who have experience installing and configuring system boards. The equipment can be installed in a restricted access location (...

  • Page 17

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-3 2.2 location of connectors of main board *memory assembly priority: (1) dimm1 (2) dimm2.

  • Page 18

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-4 leds on front panel of fws-2350 connectors on rear panel of fws-2350

  • Page 19

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-5 2.3 mechanical drawing of main board.

  • Page 20

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-6.

  • Page 21

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-7 2.4 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: label function cmos1 cmos s...

  • Page 22

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-8 sata6g_1/2 sata3 interface sata3g_1/2 sata2 interface cn8.9.10.11 sata power cn13 mini pci-e socket cn4/cn6 lan led pinheader.

  • Page 23

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-9 2.6 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often p...

  • Page 24

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-10 2.7 cf power selection (jp1) jp1 function 1-2 5v 2-3 3.3v (default) 2.8 auto pwrbtn selection (jp2) jp2 function 1-2 don ’t use auto pwrbtn (default) 2-3 use auto pwrbtn 2.9 cmos setting selection (cmos1) cmos1 fu...

  • Page 25

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-11 15 l4_act 16 l4_100 17 l5_act# 18 l5_1k 19 l5_act 20 l5_100 21 l6_act# 22 l6_1k 23 l6_act 24 l6_100 2.11 front panel connector (cn5) pin signal pin signal 1 power on button (-) 2 power on button (+) 3 hdd led(-) 4...

  • Page 26

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-12 2.13 sata power connector (cn8.9.10.11) pin signal pin signal 1 +12v 2 gnd 3 gnd 4 +5v 2.14 4-pin atx power connector (cn16) pin signal pin signal 1 gnd 2 gnd 3 +12v 4 +12v 2.15 pin header (usb1) pin signal pin si...

  • Page 27

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-13 2.17 hard disk installation step1: remove the cover step 2: slide right to remove casing.

  • Page 28

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-14 step 3: turn screw clockwise to open hdd casing step 4: attach all four screws of the casing to the hdd.

  • Page 29

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-15 step 5: attach the sata and power cable to the hdd step 6: place the hdd onto the hdd bracket of the casing.

  • Page 30

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-16 step 7: cover up the casing.

  • Page 31

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-17 step 8: turn the screw counter-clockwise to secure the casing step 9: connect the sata and power cables to the mainboard.

  • Page 32

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-18 step 10: place the casing into the chasis, slide right to secure.

  • Page 33

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-19 step 11: close and secure the cover 2.18 vga card installation step 1: remove the cover.

  • Page 34

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-20 step 2: insert the vga card into mini-pci slot step 3: secure the card by tightening the screws.

  • Page 35

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-21 step 4: connect your vga device. Both screws must be secured for the connector to function properly step 5: close and secure the cover.

  • Page 36

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 2 quick installation guide 2-22 china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon boxer/ industrial system 部件名称 有毒有害物质或元素 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 × ○ ○ ○ ○ ○ 外壳 × ○ ○ ○ ○ ○ 中央处...

  • Page 37: Ami

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-1 ami bios setup chapter 3.

  • Page 38

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-2 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There a...

  • Page 39

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-3 3.2 ami bios setup ami bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram and bios nvram so that it retains the set...

  • Page 40

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-4 setup menu setup submenu: main.

  • Page 41

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-5 setup submenu: advanced.

  • Page 42

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-6 usb configuration options summary: legacy usb support enabled optimal default, failsafe default disabled auto enables bios support for legacy usb support. When enabled, usb can be functional in legacy environment like dos. A...

  • Page 43

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-7 super io configuration.

  • Page 44

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-8 serial port 1 configuration options summary: serial port disabled enabled optimal default, failsafe default allows bios to en/disable correspond serial port. Change settings auto optimal default, failsafe default io=3f8h; ir...

  • Page 45

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-9 serial port 2 configuration options summary: serial port disabled optimal default, failsafe default enabled allows bios to en/disable correspond serial port. Change settings auto optimal default, failsafe default io=2f8h; ir...

  • Page 46

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-10 h/w monitor.

  • Page 47

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-11 power management.

  • Page 48

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-12 s5 rtc wake settings (fixed time) options summary: wake system with fixed time disabled optimal default, failsafe default enabled en/disable system wake on alarm event. When enabled, system will wake on the hr:min:sec speci...

  • Page 49

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-13 s5 rtc wake settings (dynamic time) options summary: wake system with dynamic time disabled optimal default, failsafe default enabled en/disable system wake on alarm event. When enabled, system will wake on current time + i...

  • Page 50

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-14 lan bypass configuration.

  • Page 51

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-15 options summary: lan bypass controller disabled enabled optimal default, failsafe default configure lan bypass function lan bypass status led configuration led off optimal default, failsafe default red led on red led blink ...

  • Page 52

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-16 serial port console redirection options summary: console redirection disabled enabled optimal default, failsafe default console redirection enable or disable.

  • Page 53

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-17.

  • Page 54

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-18 options summary: terminal type vt100 vt100+ optimal default, failsafe default vt-utf8 ansi emulation: ansi, vt100, vt100+, vt-utf8 bit per second 9600 19200 38400 57600 115200 optimal default, failsafe default selects seria...

  • Page 55

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-19 setup submenu: chipset.

  • Page 56

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-20 processor configuration.

  • Page 57

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-21 sata configuration.

  • Page 58

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-22 options summary: sata controller enabled optimal default, failsafe default disabled enables/disables sata controller if supported by current cpu sku. Sata mode ahci ide optimal default, failsafe default select ide / ahci mo...

  • Page 59

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-23 north bridge chipset configuration.

  • Page 60

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-24 south bridge chipset configuration options summary: iqat enabled optimal default, failsafe default disabled hides iqat device from an os usb support enabled optimal default, failsafe default disabled usb support parameters ...

  • Page 61

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-25 security change user/supervisor password you can install a supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features...

  • Page 62

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-26 setup submenu: boot options summary: setup prompt timeout 1 default 1-65536 number of seconds to wait for setup activation key. 65535(0xffff) means indefinite waiting. Bootup numlock state on default off select the keyboard...

  • Page 63

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-27 bbs priorities.

  • Page 64

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 3 ami bios setup 3-28 setup submenu: save & exit.

  • Page 65: Driver

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 4 driver installation 4-1 0b driver installation chapter 4.

  • Page 66

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 4 driver installation 4-2 the fws-2350 comes with an autorun cd-rom that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver cd, the driver dvd-title will auto start and show the installati...

  • Page 67

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 chapter 4 driver installation 4-3 4.1 installation: insert the fws-2350 cd-rom into the dvd-rom drive and install the drivers. Step 1 – install lan driver 1. Move the base driver tar file to the directory of your choice. For example, use '/home/username...

  • Page 68: Programming The

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix a programming the watchdog timer a-1 programming the watchdog timer appendix a.

  • Page 69

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix a programming the watchdog timer a-2 a.1 watchdog timer initial program table 1 : superio relative register table default value note index 0x2e (note1) sio mb pnp mode index register 0x2e or 0x4e data 0x2f (note2) sio mb pnp mode data register ...

  • Page 70

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix a programming the watchdog timer a-3 ************************************************************************************ // superio relative definition (please reference to table 1) #define byte sioindex //this parameter is represented from no...

  • Page 71: Main

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix a programming the watchdog timer a-4 ************************************************************************************ void main (){ // procedure : aaeonwdtconfig // (byte)timer : time of wdt timer.(0x00~0xff) // (boolean)unit : select time ...

  • Page 72

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix a programming the watchdog timer a-5 ************************************************************************************ // procedure : aaeonwdtenable void aaeonwdtenable () { wdtenabledisable( enableldn, enablereg, enablebit, 1 ); } // proced...

  • Page 73

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix a programming the watchdog timer a-6 ************************************************************************************ void sioentermbpnpmode() { switch(sioindex){ case 0x2e: iowritebyte(sioindex, 0x87); iowritebyte(sioindex, 0x01); iowriteb...

  • Page 74

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix a programming the watchdog timer a-7 ************************************************************************************ void siobitset(byte ldn, byte register, byte bitnum, byte value) { byte tmpvalue; sioentermbpnpmode(); sioselectldn(byte l...

  • Page 75: I/o  Information

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix b i/o information b - 1 i/o information appendix b.

  • Page 76

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix b i/o information b-2 b.1 i/o address map.

  • Page 77

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix b i/o information b-3.

  • Page 78

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix b i/o information b-4 b.2 memory address map.

  • Page 79

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix b i/o information b-5.

  • Page 80

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix b i/o information b-6 b.3 irq mapping chart.

  • Page 81

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix b i/o information b-7.

  • Page 82

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix b i/o information b-8.

  • Page 83

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix b i/o information b-9.

  • Page 84

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix b i/o information b-10

  • Page 85: Standard  Lan  Bypass

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix c standard firewall platform setting c-1 standard lan bypass platform settings appendix c.

  • Page 86

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix c standard firewall platform setting c-2 c.1 status led fws-2350 provides a led indicator which can show any led status controlled by the aaeon sdk. Users are able to program the led status to express different status. C.2 status led configurat...

  • Page 87

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix c standard firewall platform setting c-3 c.3 status led sample code ********************************************************************************************** #define byte cpld_slave_address //this parameter is represented from note1 #defin...

  • Page 89

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix c standard firewall platform setting c-5 c.4 lan bypass fws-2350 provides lan bypass kit and allow uninterrupted network traffic even if a single in-line appliance is shut down or became unresponsive. C.5 lan bypass configuration table 1 : id s...

  • Page 90

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix c standard firewall platform setting c-6 wdt_en use for configuring wdt function behavior to lan kit, when wdt triggered. 0: normal wdt reset (default) 1: force bypass act_en use for activating programming of lan kit. It is edge triggering (fal...

  • Page 92

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix c standard firewall platform setting c-8 bdata = smbusreadbyte(cpld_slave_address, offset); smbuswritebyte(cpld_slave_address, offset, bdata & 0x7f); sleep(500); bdata = smbusreadbyte(cpld_slave_address, offset); smbuswritebyte(cpld_slave_addre...

  • Page 93: Main

    N e t w o r k ap p l i a n c e f w s - 2 3 5 0 appendix c standard firewall platform setting c-9 tmpvalue = inportb (ioaddr); return (tmpvalue & (1 } ************************************************************************************ void main (){ byte rstbtn; rstbtn = get_value (btn_sts, btn_sts_r...