1. DL manuals
  2. Aarrow
  3. Stove
  4. Becton 7 MK 3
  5. Operating And Installation Manual

Aarrow Becton 7 MK 3 Operating And Installation Manual

Manual is about: Aarrow Fires Bekton Series Indoor Gas Fireplace Models Becton Bunny, Becton 7 mk3 Operating and Installation Manual

Summary of Becton 7 MK 3

  • Page 1

    Aarrow fires ltd the fireworks bridport dorset, dt6 3be great britain tel. (44) 01308 427234 fax. (44) 01308 427441 www.Aarrowfires.Com the becton mk 3 range of gas stoves operating & installation manual please retain these instructions for future reference for use in countries gb & ie rev 11 part n...

  • Page 2

    Congratulations on your choice of an aarrow stove. More than 20 years experience has been put into the development of our becton family to ensure ultimate performance and years of trouble free enjoyment. Every detail on the fire has been carefully engineered and designed which is why we are so confi...

  • Page 3

    Page introduction safety notices 4 general information 4 statutory requirements 5 operating instructions technical data 6 fire dimensions 6 fitting the lining panels 7 arranging the coals 8 lighting & controlling the fire 9-10 installation installing the fire 11 fitting the feet 11 flue system 11-13...

  • Page 4

    References in this manual to british standards and statutory regulations and requirements apply only to the united kingdom. For ireland the rules in force must be used. Before installation, check that the local distribution conditions, nature of the gas, pressure and the adjustment of the appliance ...

  • Page 5

    Important notices a qualified gas engineer must carry out the installation and servicing of this appliance in accordance with these instructions and in compliance with current building regulations. Such person must be a registered corgi engineer. This appliance is designed to run on natural gas only...

  • Page 6

    6 becton bunny & becton 7 mk3 gas stoves operating instructions fire dimensions category i 2h for use in gb and ie at a supply pressure of 20mbar technical data becton bunny natural gas becton 7 natural gas main burner injector max. Heat setting heat input (net) 3.7 kw 5.0 kw gas rate 0.391m 3 /hour...

  • Page 7

    Fitting the lining panels becton 7 only. The lining panels supplied are to be installed into the fire before the coal matrix is fitted. Note: the lining panels are reversible (brick or plain pattern) ensure the appliance is cold. With the fire door open, the glass retaining frame and the coal set re...

  • Page 8

    Arranging the coals safety notice - please see safety notices ref. Coal set page 4. Warning: the coals and the coal matrices are fragile ensure they are handled carefully. Ensure location is correct. Do not force the matrix into position. If the coals and/or the coal matrices are damaged they must b...

  • Page 9

    Lighting & controlling the fire under no circumstance must the fire be operated if the glass is cracked or broken. Open the gas control access door situated at the bottom of the appliance. Always use the control door handle. Step 1a. To ignite the pilot push the control knob in, turn anti-clockwise ...

  • Page 10

    Fig 5d fig 5e step 3. To turn the main burner off while keeping the pilot alight, rotate the operating knob back to the pilot position. (fig 5e) fig 5f step 4 . To extinguish the pilot, turn the control knob to the off position. (fig 5f) incorporated into the pilot assembly is a flame failure device...

  • Page 11

    Installing the fire your corgi qualified gas engineer should install the fire in accordance with the following regulations and standards:- the gas safety (installation and use) regulations 1998 (as amended). The building regulations for england and wales 2000 ref; approved document j 2002 edition (i...

  • Page 12

    The becton gas stove is designed so that the flue can be fitted to either the top or the rear of the appliance. Fit the flue spigot and blanking plate for either top or rear flue outlet in accordance with figure 6a or 6b (below). Lock the blanking plate in place by rotating anti- clockwise and tight...

  • Page 13

    Fig. 7b. Fig. 7c fire location the appliance must not be installed in a room or space, which contains a bath or shower. This fire is designed for use with either top or rear flue outlets and must be mounted on a hearth with a minimum of 12mm non-combustible material thickness. There must be a minimu...

  • Page 14

    The minimum height from the extreme top surface of the fire to the underside of a shelf or other projection made of wood or any other combustible material is shown on graph 1. Graph 1.Combustible shelf clearances the recommended minimum height from the extreme top surface of the fire to the undersid...

  • Page 15

    Hearth requirements to comply with current building regulations the fire must stand on a fireproof hearth, which has an upper fireproof layer of 12mm non-combustible material. If the rear of the fire is to be pushed up against a surface it must be of a non-combustible material. The hearth must protr...

  • Page 16

    Fire testing flame failure device testing step 1 ignite the appliance in accordance with page 9 and run for 60 seconds. Step 2 turn the appliance off to extinguish the pilot, listen for a snap at the control valve. This should occur within 60 seconds of the pilot flame being extinguished. The snap s...

  • Page 17

    Becton bunny & becton 7 mk3 gas stoves 17 installation check list checklist hearths, fireplaces, flues and chimneys this checklist is to ensure hearths, fireplaces, flues and chimneys are satisfactory, and to show what you have done to comply with the requirements of the building regulations 2000 ap...

  • Page 18

    Detail of pilot assembly it is strongly recommended to leave the pilot on permanently. This will keep the fire and its components, including the ceramic coal set in a warmer state and assist ignition to the burner. This in turn will reduce condensation in the chimney and any associated flue problems...

  • Page 19

    Becton bunny & becton 7 mk3 gas stoves 19 servicing door trim becton fire doors are fitted with a brushed steel finish trim as standard. The trim is secured using 3 off tabs and located in the slot section of the trim and secured with 3 off nuts. (see fig. 11a below.) fig. 11a location of the 3 off ...

  • Page 20

    Burner assembly to remove the burner assembly proceed as follows; ensure the appliance is cold. Step 1 turn off the gas supply at the gas service cock. Step 2 disconnect the supply inlet pipe at the rear of the fire. Step 3 open door and remove the glass frame and glass gasket assembly. Step 4 remov...

  • Page 21

    Annual service this gas appliance must be serviced every twelve months by a qualified gas engineer. See "safety notices" ref coal set page 4. Ensure the appliance is cold. Step 1 isolate the gas supply to the fire using the gas cock supplied at installation. Step 2 open the fire door, (held closed u...

  • Page 22

    22 becton bunny & becton 7 mk3 gas stoves servicing is the gas supply turned on? Does the pilot ignite? Yes does the pilot stay alight? Yes does the main burner light? Yes fire satisfactory no is their air in the system? Yes is the main injector blocked? Yes clean and replace as necessary is the sup...

  • Page 23

    General components spare parts can be obtained by contacting the original supplier of the fire or aarrow fires. Fire body ancillary components. Only use genuine aarrow parts. Accessories and options paint- matching aerosol paint to tone in any connecting flues, pipes or surrounding metalwork tracery...

  • Page 24

    24 becton bunny & becton 7 mk3 gas stoves notes.

  • Page 25

    Becton bunny & becton 7 mk3 gas stoves 25 notes.

  • Page 26

    26 becton bunny & becton 7 mk3 gas stoves spare parts 1. Becton 7 mk3 coal set - afgs1075 afgs1074 - afgs089 afgs089 afgs090 afgs090 afgs091a afgs091 afgs1073 afgs1073 afs047 afs047 1a. Becton bunny mk3 coal set 2. Co-pilot assembly 3. Elbow injector 4. Gas control valve 5. Magnetic catch for mk3 ga...

  • Page 27

    Becton bunny & becton 7 mk3 gas stoves 27 spare parts afgs1085 afgs1085 afgs1076 afgs1077 afgs080 afgs080 afs094a afs095 afgs1078 afgs1079 afgs1080 afgs1081 7. Control door handle assembly 8. Burner & fixing 9. Pipe set complete with connectors 10. Decorative door surround (trim) 11. Fire door assem...

  • Page 28

    28 becton bunny & becton 7 mk3 gas stoves spare parts - afgs1072 afgs093 afgs093 15. Becton 7 mk3 lining kit 16. Large ceramic panel part description visual aid (not to scale) bunny mk3 part no. Becton 7 mk3 part no. Afgs094 afgs094 17. Medium ceramic panel 18. Small ceramic panel afgs1084 afgs1084 ...

  • Page 29

    Guarantee once again we would like to thank you for buying a becton fire. When you buy an aarrow fire, you are not only buying a first class appliance - you are buying a commitment from us to look after you and your appliance. The becton gas stoves come with a lifetime guarantee against splitting or...

  • Page 30

    Should you have any questions about your becton gas stove that is not covered in this manual please con- tact your aarrow retailer. Please keep all repair receipts safely. Please ensure you have this manual available when an engineer visits as they will complete the service record chart. 30 becton b...

  • Page 31: Lifetime Guarantee

    Lifetime guarantee for your peace of mind aarrow fires gives a lifetime guarantee against manufacturing defects of the main body* of its becton range of fires. Additionally, all other parts are covered by a one year no quibble replacement guarantee. This guarantee covers replacement of the item only...

  • Page 32: I’Ve Checked It

    Final factory check list bk027 model.................................. Serial no............................. I’ve checked it and it’s o.K. Assembled by............................. Checked by ................................ Date of purchase.................................... Name and address of s...