1. DL manuals
  2. AAS
  3. Intercom System
  4. PhoneAire 16-1050
  5. Installation And Programming Instructions

AAS PhoneAire 16-1050 Installation And Programming Instructions

Summary of PhoneAire 16-1050

  • Page 1

    1 installation and programming instructions for the phoneaire model 16-1050

  • Page 2: Fcc Requirements

    2 fcc requirements 1. This equipment complies with part 68 of the federal communications commission rules. On the inside panel of this equipment is a label that contains, among other information, the fcc registration number, facility interface code (fic) and service order code (soc). This informatio...

  • Page 3

    3 doc requirements equipment attachment limitations notice: this equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate terminal equipment technical requirements document(s). This is confirmed by marking the equipment with the indu...

  • Page 4: Important Tips

    4 important tips 1. Your phoneaire contains static sensitive components. Proper grounding techniques should be exercised during installation to prevent damage to circuit board. 2. Additional surge protection is highly recommended to provide extra lighting protection. 3. Please follow the instruction...

  • Page 5

    5 2. Mounting the phoneaire gate unit to an aas gooseneck pedestal (18-001) or double height gooseneck (18-003) locate the four carriage bolts and four hex nuts found inside the unit box. Place the unit up to the pedestal flange and insert the four carriage bolts from the backside. Secure the unit t...

  • Page 6

    6.

  • Page 7

    7 power n/o com n/c n/o com n/c relay a relay b event input 12 vac or vdc (12 vac adapter provided) 16-1050 phoneaire transmitter station hook-up diagram device control relays this diagram show the basic hook-ups for the remote sytation (“gatebox”). Installation is common to most keypad installation...

  • Page 8: 30-029 Circuit Board

    8 power 12vac only bypass switch from phone co to phones led 30-029 circuit board receiver unit pbx jumper setup reset.

  • Page 9: 30-028 Circuit Board

    9 30-028 circuit board transmitter unit power relays event input night light control unit & master reset speaker volume microphone adjust.

  • Page 10: Phoneaire System Intercom

    10 phoneaire system intercom operation: a visitor desiring access will push the call button on the outside control station, causing a special ring signal to be sent to the inside phone. Picking up the phone before 10 rings are completed will establish intercom mode between the receiver and the contr...

  • Page 11: Phoneaire Keypad

    11 intercom mode. Intercom mode is also terminated after five minutes of inactivity --- i.E. Five minutes after the last gate command, or five minutes after it is started if no gate commands are given. Intercom mode and use of the keypad are mutually exclusive: if someone is in the middle of enterin...

  • Page 12

    12 unit will be enabled. An override code is provided. “one shot code” this code is a programmable four digit code that disables itself after one use. The user can enable this code for reuse using the keypad or telephone. Goodbeeps & errorbeeps your unit will beep each time a key is pressed. The "*"...

  • Page 13: Programming

    13 press and release hwreset button. The idle mode the idle mode is the normal mode of operation. When in this mode the unit sits and waits for data from the keypad. When in this mode you will have approximately 4 seconds between key presses. If this time is exceeded, you will receive an error. The ...

  • Page 14

    14 sub-mode 1 (program relay a access codes) to program new relay a access codes enter the following; (master code) + 1 + (new code) + (next new code) etc......... ( # to exit) should you make a code entry error, simply press the * key and enter the correct code. You may select any 4 digit code you ...

  • Page 15

    15 mode see the unit reset instructions on pages 10 & 11. Note: you can also toggle the sleep code with the telephone. (see intercom operating instructions.) to program or change your sleep code enter the following; (master code) + 4 + 1 + sleep code should you make a code entry error, simply press ...

  • Page 16

    16 double beep = disabled notes: 1) pressing * will clear the phone number digits entered. 2) pressing # will “enter” the phone number. A good beep will sound if 7, 10, or 11 digits have been entered when # is pressed. If not, a bad beep will sound and call forwarding will be disabled if it was enab...

  • Page 17

    17 program mode if the memory reaches capacity. When memory is full you will not be able to enter this sub-mode and will receive an error if entry is attempted. Sub-mode 8 (enable/disable 3 strikes-you’re out) explanation: this feature is desirable to keep unwanted persons from successively entering...

  • Page 18

    18 (master code) + 9 (*current mode) + 2 to program the event input as remote open enter the following; (master code) + 9 (*current mode) + 3 + (*relay to activate) to program the event input as night light enter the following; (master code) + 9 (*current mode) + 4 to disable the event input enter t...

  • Page 19: Troubleshooting

    19 troubleshooting at the gate, press call button, get 1 and a half rings and then error tone. Unit can not find house unit. Either move units closer, different locations, or try antenna extension. At the gate, press call button, get 3 rings and then error tone. Units are talking but no phone line. ...

  • Page 20

    20 customer service: 800-541-5677 customer service is available free of charge. Hours are 8:00 a.M. To 5:00 p.M. Mst. If you call, please have your model and serial # to help our technicians assist you with any problems you have. E-mail: customerservice@americanaccess.Com technical support: 800-541-...