- DL manuals
- Aastra
- IP Phone
- DBC 422
- Installation Instructions Manual
Aastra DBC 422 Installation Instructions Manual
Summary of DBC 422
Page 1
Installation instructions installation instructions 1531-dbc 422 02 b3 2013 12 02 dbc 422 and dbc 425 catarina sten csten arne miler arne miler.
Page 2
1531-dbc 422 02 uen b3 2013-12-02 2 copyright © copyright aastra technologies limited, 2013. All rights reserved. Disclaimer no part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without not...
Page 3: General
Dbc 422 and dbc 425 3 1531-dbc 422 02 uen b3 2013-12-02 1 general these installation instructions are valid for the ip phones dbc 422, also called dialog 4422 and for dbc 425, also called dialog 4425. These telephones use the h.323 protocol. 1.1 scope these ip phones can be connected to a number of ...
Page 4
1531-dbc 422 02 uen b3 2013-12-02 4 g eneral a password for each ip extension can be initiated in the exchange. The password is used to check that the user is allowed to log on with the entered extension number. Asb 501 04 has support for automatic gatekeeper discovery, which means that the ip addre...
Page 5: 1.2 Environmental
Dbc 422 and dbc 425 5 1531-dbc 422 02 uen b3 2013-12-02 1.2 environmental requirements the products covered in these installation instructions comply with the prerequisites stipulated for placing appliances in office and exchange room environments. 2 aids wall mounting requires additional screws and...
Page 6: Earthing/grounding
1531-dbc 422 02 uen b3 2013-12-02 6 e arthing / grounding these phones comply with the power class signature. The phone reports power class 1 which means less than 4 w required. 5 earthing/grounding no special earthing or grounding is needed. The ip phone needs a shielded ethernet cable for the netw...
Page 7: Cabling
Dbc 422 and dbc 425 7 1531-dbc 422 02 uen b3 2013-12-02 6 cabling the maximum line length between an ip phone and the lan is 100 metres (328 feet) according to ieee 802.3. Category 5 cables are recommended. The following ethernet category 5 cable can be ordered from aastra: • tsr 901 0452/3000 the f...
Page 8: Installation
1531-dbc 422 02 uen b3 2013-12-02 8 i nstallation 7 installation 7.1 how to start a new phone to select the protocol, 7.6 select h.323 protocol on page 21. Connect one end of the network cable to the network outlet and the other end to the connector marked line on the bottom of the ip phone. 6 cabli...
Page 9
Dbc 422 and dbc 425 9 1531-dbc 422 02 uen b3 2013-12-02 figure 5: verify that the dhcp parameter is set to yes, otherwise press the speaker key and change the value to yes. Normally the phone gets the ip address to the sw server automatically from dhcp option 43 or from dns srv records. Step down in...
Page 10
1531-dbc 422 02 uen b3 2013-12-02 10 i nstallation the phone fetches the own ip address and other data from the dhcp server, see 7.11.2 data from dhcp on page 30. Then the following menu is shown: figure 9: the phone fetches the configuration file from the sw server. If the phone cannot get the file...
Page 11
Dbc 422 and dbc 425 11 1531-dbc 422 02 uen b3 2013-12-02 figure 12: if the emergency call function is disabled the display shows: figure 13: the next step is to register the phone towards the gatekeeper. The ip extension must already be initiated in the system. The directory number used at the previ...
Page 12
1531-dbc 422 02 uen b3 2013-12-02 12 i nstallation figure 16: the x indicates a timer counting down seconds. To change the ip settings, enter the administrator mode before the timer x is counted down to zero. If the administrator mode is not entered, or c is pressed, the currently stored settings wi...
Page 13
Dbc 422 and dbc 425 13 1531-dbc 422 02 uen b3 2013-12-02 note: it is not possible to only update the boot software. If the boot soft- ware will be updated, the application has to be updated as well. The following menu appears if a new bootrom shall be loaded: figure 18: press the speaker key to upda...
Page 14: 7.3
1531-dbc 422 02 uen b3 2013-12-02 14 i nstallation there is a power failure during this phase, the phone has to load the soft- ware again. The next menu shows selftest ok. The next step is to set the gatekeeper’s ip address and register the extension towards the gatekeeper. This is described in 7.2....
Page 15
Dbc 422 and dbc 425 15 1531-dbc 422 02 uen b3 2013-12-02 figure 23: verify that the dhcp parameter is set to yes, otherwise press the select (f4) key and change the value to yes. Normally the phone gets the ip address to the sw server automatically from dhcp option 43 or from dns srv records. Step d...
Page 16
1531-dbc 422 02 uen b3 2013-12-02 16 i nstallation figure 25: enter the lan access password and press the log on key. If the authentication is successful the normal boot sequence continues. The following menu appears: figure 26: the phone fetches the own ip address and other data from the dhcp serve...
Page 17
Dbc 422 and dbc 425 17 1531-dbc 422 02 uen b3 2013-12-02 figure 28: the software is loaded internally in the phone. This process takes about 15 seconds. Figure 29: the phone performs a test to verify operation of the phone circuits. The next step is to set the ip address to the gatekeeper. To set th...
Page 18
1531-dbc 422 02 uen b3 2013-12-02 18 i nstallation figure 31: enter the password or pin and press log on (f4). Figure 32: now the phone is ready for making and receiving calls. For a description of how to use the phone, see directions for use for each platform. 7.3.2 manually setting of the fixed ip...
Page 19
Dbc 422 and dbc 425 19 1531-dbc 422 02 uen b3 2013-12-02 to change the ip settings, enter the administrator mode before the timer x is counted down to zero. If the administrator mode is not entered, or no change (f4) is pressed, the currently stored settings will be used and the getting configuratio...
Page 20
1531-dbc 422 02 uen b3 2013-12-02 20 i nstallation figure 35: press (yes) (f3) to update the software. The x indicates a timer counting down seconds. If the no (f4) key is not pressed during this time, yes is selected automatically. If no (f4) is pressed, the phone will use the current version of th...
Page 21: 7.4 Delivery
Dbc 422 and dbc 425 21 1531-dbc 422 02 uen b3 2013-12-02 figure 38: it is important that the power to the phone is not disconnected while this text is shown in the display. This process takes a couple of minutes. If there is a power failure during this phase, the phone has to load the soft- ware aga...
Page 22: 7.7 Sw
1531-dbc 422 02 uen b3 2013-12-02 22 i nstallation 7.7 sw loading the software to be loaded into the phone is to be stored on a web server with http protocol. This web server is called sw server in the menus and in this document. The following files are stored on the sw server: d42x02-applic_r1a.Dat...
Page 23
Dbc 422 and dbc 425 23 1531-dbc 422 02 uen b3 2013-12-02 • use the telephony domain name received in the vendor specific field in the dhcp messages, 7.11.2 data from dhcp on page 30. • subnet method, 7.8.3 subnet method on page 23 • set the ip address of the sw server manually in the phone. In this ...
Page 24: 7.9
1531-dbc 422 02 uen b3 2013-12-02 24 i nstallation • subnet method • the default configuration file is fetched. This file is stored under /dbc42x02/dbc42x02-config.Txt. 7.9 software server (sw server) a software server with the http protocol is used for storing the firmware for the ip phone. The ip ...
Page 25
Dbc 422 and dbc 425 25 1531-dbc 422 02 uen b3 2013-12-02 the files according to section, see 7.7 sw loading on page 22, must be stored on the server. The file names must be according to what is described below, 7.9.3 directory structure on page 25. Note: when storing the files on the software server...
Page 26
1531-dbc 422 02 uen b3 2013-12-02 26 i nstallation figure 39:directory structure using domain names if the subnet method is used, 7.8.3 subnet method on page 23, the direc- tory structure will be as in the example below. In this example the phones belonging to the first group have the network addres...
Page 27: 7.10
Dbc 422 and dbc 425 27 1531-dbc 422 02 uen b3 2013-12-02 figure 40:directory structure using the subnet method 7.10 dns srv resource records to get necessary ip addresses into the phone, one option is to use the dns (domain name server) srv (service) resource records. The following data can be retri...
Page 28
1531-dbc 422 02 uen b3 2013-12-02 28 i nstallation this case the phone will get the sw server ip address from dns srv. • the ip address to the ip phone administrator server. • the ip address to the sip proxy server the dns srv handling does only work when dhcp is used and when the dhcp server points...
Page 29
Dbc 422 and dbc 425 29 1531-dbc 422 02 uen b3 2013-12-02 the ip address to the ip phone administrator server in the dns srv resource records, the following data has to be set to find the ip address to the ip phone administrator server: service _aas442x_smgt._tcp (applications up to and including r7k...
Page 30: 7.11 Dhcp
1531-dbc 422 02 uen b3 2013-12-02 30 i nstallation 7.11 dhcp server 7.11.1 installation installation of the dhcp (dynamic host configuration protocol) server should be done according to the documentation of the manufacturer. Both pc and unix versions are supported. The following dhcp servers have be...
Page 31
Dbc 422 and dbc 425 31 1531-dbc 422 02 uen b3 2013-12-02 for the complete usage of the domain name, see section 7.17 domain name on page 49. 7.11.3 dhcp settings for option 43 and 60 dhcp option 60 (vendor class identifier) and option 43 (vendor specific information field) are used by the telephone ...
Page 32
1531-dbc 422 02 uen b3 2013-12-02 32 i nstallation ericsson ip-phone , see section 7.11.3.2 vendor specific information field on page 32. 7.11.3.2 vendor specific information field the vendor specific information field (option 43) is coded as shown in the figure below. Figure 42:vendor specific info...
Page 33
Dbc 422 and dbc 425 33 1531-dbc 422 02 uen b3 2013-12-02 tag 07 (t7 in the figure): vlan identity 3 for the telephone, in ascii text format. Note: the vlan identity for the telephone defined here in option 43 must not be equal to the vlan identity for the pc defined in the configuration file. For mo...
Page 34
1531-dbc 422 02 uen b3 2013-12-02 34 i nstallation 7.11.4.1 define vendor class figure 43:define vendor classes select define vendor classes to get the menu where the vendor classes are entered..
Page 35
Dbc 422 and dbc 425 35 1531-dbc 422 02 uen b3 2013-12-02 figure 44: dhcp vendor classes if the vendor class aastra ip-phone does not exist, press add to create the new vendor class. In the next menu the id string aastra ip-phone has to be entered:.
Page 36
1531-dbc 422 02 uen b3 2013-12-02 36 i nstallation figure 45:add vendor class it is possible to move the cursor between the binary and the ascii area to make it easier to enter the id data. When the data has been entered, press ok. Close the window and proceed to set predefined options. In some scen...
Page 37
Dbc 422 and dbc 425 37 1531-dbc 422 02 uen b3 2013-12-02 figure 47: predefined options and values select aastra ip-phone in the drop down list in the option class field and press the add button. The next menu is shown below: figure 48: option type this is the default view and data has to be entered ...
Page 38
1531-dbc 422 02 uen b3 2013-12-02 38 i nstallation the filled in dialog will look like: figure 49: filled in option type dialog press ok and the window with predefined options and values will occur again. Press ok again and the menu will be closed. 7.11.4.3 set scope options figure 50: configure opt...
Page 39
Dbc 422 and dbc 425 39 1531-dbc 422 02 uen b3 2013-12-02 select configure options. Figure 51:scope options select advanced tab and scroll in the vendor class field until aastra ip-phone is selected. Press ok. Next menu is where the id strings and the tags are set, according to the figure in section ...
Page 40
1531-dbc 422 02 uen b3 2013-12-02 40 i nstallation figure 52:windows® 2003 server dhcp settings it is possible to move the cursor between the binary and the ascii area to make it easier to enter the option 43 data. This example shows that the total length of the vendor specific informa- tion is 0x1f...
Page 41
Dbc 422 and dbc 425 41 1531-dbc 422 02 uen b3 2013-12-02 figure 53:two initiated vendor classes 7.11.5 linux dhcp settings example of settings in the linux server: subnet 192.168.6.192 netmask 255.255.255.192 { option routers 192.168.6.254; # class "aastra ip-phone" { # match option vendor-class-ide...
Page 42: 7.12 Diffserv
1531-dbc 422 02 uen b3 2013-12-02 42 i nstallation } else if substring (option vendor-class-identifier, 0, 17) = "ericsson ip-phone" { option vendor-encapsulated-options "\x11ericsson ip-phone \x01\x0b192.168.0.1\x04\x16aastradomain.Aastra.Se\x0 5\x03452"; } # # dhcp settings continued example when ...
Page 43: 7.13
Dbc 422 and dbc 425 43 1531-dbc 422 02 uen b3 2013-12-02 7.13 ip phone administrator tool the tool ip phone administrator is used to monitor the dbc 42x 02 ip phones in the network. This is useful in the following cases: • to find the ip address to the ip phones and especially to the phones without ...
Page 44
1531-dbc 422 02 uen b3 2013-12-02 44 i nstallation figure 55:ip phone administrator a log in window will pop up when starting the tool. The user name and the password is set by the system administrator at installation of ip phone administrator. The following columns exist in the gui: ip address clic...
Page 45
Dbc 422 and dbc 425 45 1531-dbc 422 02 uen b3 2013-12-02 • grey icon means: no log on attempt towards the pbx has been done • yellow icon with an exclamation mark: the phone has tried to register but has got reject back from the gatekeeper. • yellow icon: the phone has not reported anything to the i...
Page 46: 7.14 Gatekeeper
1531-dbc 422 02 uen b3 2013-12-02 46 i nstallation the snmp agent is by default disabled, but can be enabled via the configuration file. In this case it is mandatory to set the community string in the configuration file, see description of configuration file for dbc42x. The mib (management informati...
Page 47: 7.15 Automatic
Dbc 422 and dbc 425 47 1531-dbc 422 02 uen b3 2013-12-02 table 2 7.15 automatic gatekeeper discovery only certain gatekeepers (pbxes) have support for automatic gate- keeper discovery, for example mx-one tsw. Automatic gatekeeper discovery is a method to find a gatekeeper (pbx) to register to. When ...
Page 48: 7.16 Hlr
1531-dbc 422 02 uen b3 2013-12-02 48 i nstallation 7.16 hlr redundancy hlr redundancy is a function in the mx-one tse system. If the line interface module (lim), where the data for the extension (home loca- tion register) is stored, becomes unreachable, a temporary hlr will be created in another lim...
Page 49: 7.17 Domain
Dbc 422 and dbc 425 49 1531-dbc 422 02 uen b3 2013-12-02 7.16.1.3 change-back to ordinary hlr if the lim of the ordinary hlr becomes available again, the periodic keep-alive check request will be rejected by the gk (in the lim of the temporary hlr). The terminal will request a registration to the pr...
Page 50
1531-dbc 422 02 uen b3 2013-12-02 50 i nstallation table 4 tcp ports used by the phone wap (push) 2948 2948 receive from internal wap server (pbx) urq in secure mode 3727 3727 omd 5000 5001 for speech voip recording 7300 7300 rtp 16986 17012 rtcp 16987 17013 rtp port + 1 wap (reply) 49152 49152 rece...
Page 51: 7.19 Built-In
Dbc 422 and dbc 425 51 1531-dbc 422 02 uen b3 2013-12-02 port number for operator media device (omd): the port number is set in mx-one (opsai command). The same port number shall be set in the configuration file for the telephone and in the configuration of the integrated attendant workstation, now ...
Page 52
1531-dbc 422 02 uen b3 2013-12-02 52 i nstallation • from a menu where it can be manually set (both the phone- and the pc port). It is possible to change the different vlan options from the menu in the boot sequence. The following menu is shown (for dbc 425 as an example): figure 56: start up menu i...
Page 53
Dbc 422 and dbc 425 53 1531-dbc 422 02 uen b3 2013-12-02 7.20.1 automatic vlan detection with dhcp prerequisites on the lan when the phone is connected to a layer 2 switch, the switch will add the ieeee 802.1q header, to untagged frames with the default vlan iden- tity and forward the frames. The fi...
Page 54: 7.21 Security
1531-dbc 422 02 uen b3 2013-12-02 54 i nstallation at installation (and hardware reboot) the phone asks for an ip address from dhcp by initiating the dhcp negotiation with untagged messages (native lan). Dhcp provides the ip address but no vlan identity list. The phone reads the configuration file, ...
Page 55
Dbc 422 and dbc 425 55 1531-dbc 422 02 uen b3 2013-12-02 7.21.1 protection of voip signalling the signalling between the dbc 42x 02 ip phones and the gatekeeper is protected by means of tls (transport layer security) according to rfc 2246. The tls protection affects the registration and the call han...
Page 56
1531-dbc 422 02 uen b3 2013-12-02 56 i nstallation entrust sha1withrsaencryption equifax ca-1 md5withrsaencryption equifax ca-2 sha1withrsaencryption equifax sha1withrsaencryption equifax secure global ebusiness ca-1 gte cyber trust quovadis root ca2 securesign root ca1 securesign root ca2 securesig...
Page 57
Dbc 422 and dbc 425 57 1531-dbc 422 02 uen b3 2013-12-02 7.21.1.2 registration towards the gatekeeper at log on the phone promts the user to enter the extension number and the password or pin. If the user do not have a password or pin, the phone tries to log on to the insecure udp port1719. In case ...
Page 58: 7.22
1531-dbc 422 02 uen b3 2013-12-02 58 i nstallation 7.21.2 udp filtering all the udp ports that are not used, can be blocked for security reasons. For a description of all udp and tcp ports, see 7.18 selection of trans- port address (port numbers) on page 49. The default value is that the udp filteri...
Page 59
Dbc 422 and dbc 425 59 1531-dbc 422 02 uen b3 2013-12-02 figure 57:components in lan access control before the authentication the phone cannot get access to the lan or even get the ip address from the dhcp server. The authentication has to be performed periodically within 5 minutes (maximum). If the...
Page 60
1531-dbc 422 02 uen b3 2013-12-02 60 i nstallation • lan access control (auto / no) • lan access control user identity and password shall be stored in the phone or not. • lan access control user identity and password shall be valid for the phone or for the end user. In the first case the phone shall...
Page 61: 7.23
Dbc 422 and dbc 425 61 1531-dbc 422 02 uen b3 2013-12-02 • the user identity is valid for the phone, which means that the end-user can change extension number towards the pbx, without having to enter a new lan access user identity and password (default value). 7.22.3 authentication to the lan the au...
Page 62
1531-dbc 422 02 uen b3 2013-12-02 62 i nstallation mendation is to use such a password or pin to avoid that one end-user can log in with another end-user’s directory number. • for maintenance via ssh or the web interface, to be used by the network administrator or other maintenance personnel, 7.24.1...
Page 63: 7.25 Software
Dbc 422 and dbc 425 63 1531-dbc 422 02 uen b3 2013-12-02 possible to use the default password is welcome to log in to the web interface. But in this case a parameter must be changed in the configu- ration file to enable the default password option. 7.25 software version it is possible to check the s...
Page 64: 7.27
1531-dbc 422 02 uen b3 2013-12-02 64 i nstallation select the current menu. Save the entered data. Volume keys + key is used to go down one row in a listancel. - key is used to go up one row in a list and also to erase the latest entered character. The figure below shows an overview of what the keys...
Page 65: 7.28
Dbc 422 and dbc 425 65 1531-dbc 422 02 uen b3 2013-12-02 exit (f1) leave the current menu and go up one level in the menu hierarchy. Exit is used in menus where it is not possible to change data. Erase (f3) erase the latest entered character. Select (f4) select the current menu. Save (f4) save the e...
Page 66: 7.29 Factory
1531-dbc 422 02 uen b3 2013-12-02 66 i nstallation 7.29 factory default to set the phone to factory default, the following procedure must be used: • enter administrator mode, 7.30 administrator mode on page 66. • press the keys c,*,9 for a second. The following data will be set: • use dhcp • auto de...
Page 67: 7.31
Dbc 422 and dbc 425 67 1531-dbc 422 02 uen b3 2013-12-02 7.31 quality of service (qos) it is possible to view the quality of service statistics of the connection for the last 10 calls via the web interface. The statistics shows for example the delay, jitter and number of lost packets. See maintenanc...
Page 68: 7.34
1531-dbc 422 02 uen b3 2013-12-02 68 i nstallation 7.34 to change the configuration of the phone 7.34.1 methods to change the configuration it is possible to change the configuration in the phone by: • the menus, see directions for use for each platform. • the web interface, see directions for use f...
Page 69
Dbc 422 and dbc 425 69 1531-dbc 422 02 uen b3 2013-12-02 the log on procedures are described in the directions for use for respec- tive system. To change between the different log on / log off options: • select the settings menu. • enter the administrator mode. • select the log off restrictions menu...
Page 70
1531-dbc 422 02 uen b3 2013-12-02 70 i nstallation if the phone is not automatically logged on after the configuration file is read, there are the following possibilities to enter the default directory number and or the password: • enter the administrator mode and the log on with menu will appear af...
Page 71
Dbc 422 and dbc 425 71 1531-dbc 422 02 uen b3 2013-12-02 figure 61: network settings menus in dbc 422.
Page 72
1531-dbc 422 02 uen b3 2013-12-02 72 i nstallation figure 62: network settings menus in dbc 422 1) this line is only displayed if a dhcp server is used. It shows the dns (domain name server) name of the phone and it is used when accessing the phone from a web browser. The table below explains the ab...
Page 73
Dbc 422 and dbc 425 73 1531-dbc 422 02 uen b3 2013-12-02 7.34.5 change ip settings in dbc 425 to change the ip settings it is possible to use the menus in the phone or the web interface. When using the menus, select the settings menu by using the navigation key, enter the administrator mode, press d...
Page 74: 7.35 Absence
1531-dbc 422 02 uen b3 2013-12-02 74 i nstallation 7.35 absence services (only dbc 425). The phone has menu support for activation and deac- tivation of: • absence reason (message diversion) • follow me • external follow me • profile for personal number when the user selects an absence service the p...
Page 75: 7.37 Backup
Dbc 422 and dbc 425 75 1531-dbc 422 02 uen b3 2013-12-02 • perform the update of the phones according to the method for the current system. For mx-one see operational directions for ip extension . • for the phones that are registered in the gatekeeper the following applies: – the phones will downloa...
Page 76: 7.38 Emergency
1531-dbc 422 02 uen b3 2013-12-02 76 i nstallation main office works again, the ip phones un-register from the backup gate- keeper and register to the pbx in the main office. The procedure to get this working in the ip phones is: • define in the configuration file, used by the phones in the branch o...
Page 77: 7.39
Dbc 422 and dbc 425 77 1531-dbc 422 02 uen b3 2013-12-02 when the emergency call function is enabled in the configuration file, the emergency number is shown in the log on menu. When the user lifts the handset the dial tone is heard although the phone is not logged on. When the user dials the emerge...
Page 78: 7.41 Automatic
1531-dbc 422 02 uen b3 2013-12-02 78 i nstallation 7.41 automatic answer with this feature the call is answered automatically in handsfree mode. This feature is set by the system administrator. The following options are available: • with delay, which means that one ring signal is heard before the ca...
Page 79: 7.45 Corporate
Dbc 422 and dbc 425 79 1531-dbc 422 02 uen b3 2013-12-02 for the call handling and the phone (omd) is used for the speech. Omd can only be used with mx-one. The interface between the omd and the gatekeeper is not based on h.323, it uses a proprietary signalling. Depending on that the gatekeeper is n...
Page 80: 7.46 Wap
1531-dbc 422 02 uen b3 2013-12-02 80 i nstallation an xml parser or a wap browser. The user can select the telephone number in the search result and initiate a call via the gatekeeper. The corporate directory tab corpdirectory is only visible if the ip address to the corporate directory server is en...
Page 81: 7.47
Dbc 422 and dbc 425 81 1531-dbc 422 02 uen b3 2013-12-02 to make it easy to access such pages, a wap portal with links to the wanted internet pages can be created. The portal (home page) must be adapted for each customer site. The address of the wap portal is defined in the configuration file see th...
Page 82
1531-dbc 422 02 uen b3 2013-12-02 82 i nstallation the phone contacts are stored on an ftp server that can be defined in the configuration file. The stored file will be loaded from the ftp server when the phone is registered to the gatekeeper. The name of the file consists of the extension number to...
Page 83
Dbc 422 and dbc 425 83 1531-dbc 422 02 uen b3 2013-12-02 • right-click and select new • select virtual directory. Name the virtual directory according to the physical directory created above. Enable read and write as access permission. 7.47.2 fastream (for windows) fastream netfile ftp / web server ...
Page 84
1531-dbc 422 02 uen b3 2013-12-02 84 i nstallation actions, they will not be described here. Please refer to the documenta- tion for the used linux distribution. There are two ways that the ftp server can be used either as a stand alone server or as a part of a super server. To keep this section bri...
Page 85: 7.48
Dbc 422 and dbc 425 85 1531-dbc 422 02 uen b3 2013-12-02 in a sftp server running on linux the following must be considered: the .Txt files with contacts are stored under the folder: /home/tele- phone , when using the default user name. These folders must be enabled for read and write access. In the...
Page 86
1531-dbc 422 02 uen b3 2013-12-02 86 i nstallation figure 66:components in my dialog 4000 contacts for a description of how to use the application my dialog 4000 contacts, see the directions for use for each platform. 7.48.1 installation of my dialog 4000 contacts deliverable this application is del...
Page 87: 7.49
Dbc 422 and dbc 425 87 1531-dbc 422 02 uen b3 2013-12-02 for more details bout the installation, see the read me file included in the zip file. Configuration the file dialog4000.Jnlp contains the configuration parameters. The file can be updated with any text editor. The parameters are described in ...
Page 88: 7.50
1531-dbc 422 02 uen b3 2013-12-02 88 i nstallation the recording key is lit as soon as the telephone forwards the rtp stream to the recording system. Record on demand the led on the recording key on the phone is lit when the end-user has ordered the call to be recorded by pressing the key and the ph...
Page 89
Dbc 422 and dbc 425 89 1531-dbc 422 02 uen b3 2013-12-02 figure 68: • use a screwdriver to remove the two (a and b) plastic covers • drill two wall holes and mount the spacer sxa 112 4753/1 on the wall. These holes must be 15 mm more to the left than the centre of the phone, otherwise it will land u...
Page 90: 7.51 Post
1531-dbc 422 02 uen b3 2013-12-02 90 i nstallation figure 70: • hook the phone on the spacer screws measures for a locally manufactured spacer figure 71: 7.51 post installation measures check that it is possible to log on the phone to the system. Verify that internal and external calls can be establ...
Page 91: Dby 419 01
Dbc 422 and dbc 425 91 1531-dbc 422 02 uen b3 2013-12-02 8 installation of extra key panel dby 419 01 dbc 422 can have maximum one extra key panel. Dbc 425 can have maximum four extra key panels. The keys can be used as dial-by-function keys and monitoring keys. It is also possible to assign functio...
Page 92
1531-dbc 422 02 uen b3 2013-12-02 92 i nstallation of extra key panel dby 419 01 figure 72:attaching the dby 419 01 key panel unit to the phone mount the proper quantity of feet in recommended positions, 73 feet positions with 1 to 4 pcs dby 419 01 connected (rear view) on page 93..
Page 93: 8.2
Dbc 422 and dbc 425 93 1531-dbc 422 02 uen b3 2013-12-02 figure 73:feet positions with 1 to 4 pcs dby 419 01 connected (rear view) 8.2 post installation measures after mounting of the key panel unit connect the power to the phone and connect the phone to the lan. Program one function key per key pan...
Page 94: 420 01
1531-dbc 422 02 uen b3 2013-12-02 94 i nstallation of option unit dby 420 01 9 installation of option unit dby 420 01 make necessary arrangements to avoid electrostatic discharges: • log off the terminal and disconnect the power from the phone set. • mount the pin connector to the option unit, 74 mo...
Page 95: 9.1
Dbc 422 and dbc 425 95 1531-dbc 422 02 uen b3 2013-12-02 figure 75:mounting of option unit to the phone figure 76:press down the option unit to secure good contact. 9.1 extra bell/ busy signal for pin outlets of the external functions, 77 external cable connection on page 96.
Page 96: 9.2
1531-dbc 422 02 uen b3 2013-12-02 96 i nstallation of option unit dby 420 01 figure 77:external cable connection there are three alternatives using this function. The function is selected by the menu: settings - option unit. Extra bell: the extra bell (or lamp) is activated in parallel with the ring...