En 2csyd0201b outdoor dual ir detector installation manual.
It 2 2csyd0201b 1 general information 1.1 disclaimer all information in this document has been carefully selected and checked however abb s.P.A. Is not liable for any printing errors or technical inaccuracy. Abb s.P.A. Reserves the right to improve or change the products described in this user manua...
It 3 2csyd0201b 2 general description the outdoor dual ir detector enables to control buildings and areas from outside, and it can be installed both on a wall and on a pole. Thanks to two ir sensors, of which one can be adjusted, it is possible to detect people and to avoid false alarms caused by li...
It 4 2csyd0201b 3 installation the installation procedure encompasses the following steps: 1) device fixing. 2) programming 3) adjustment. 4) completion and test. 3.1 device fixing instructions relevant to positioning the device can be installed on a wall or on a pole, far from electromagnetic sourc...
It 5 2csyd0201b the detection of an intrusion attempt occurs only when both ir sensors are stimulated. Figure 2 graphically summarizes how the detector operates. Figure 2 sensors can be horizontally adjusted from 45 to 135 degrees. The detection area is set to 90 degrees and it can be masked. The co...
It 6 2csyd0201b figure 3 figure 4 shows the horizontal coverage diagrams according to the detector angular position (a … g, d is a factory setting) of the sensor. Figure 4.
It 7 2csyd0201b to fix the detector (figure 5): 1) remove the upper cover. 2) loosen the screw and remove the front cover. Warning: do not touch mirrors or ir sensors! 3) loosen the two front screws and remove the sensors-electronic unit. Warning: do not touch ir sensors. 4) loosen the two screws an...
It 8 2csyd0201b control unit (for further information, refer to the control unit installation manual). 3.3 adjustment it is possible to adjust the detection direction horizontally, the detection distance, the masking of the detection area (to avoid possible obstacles) and the detection sensitivity. ...
It 9 2csyd0201b figure 7 3.4 completion and test complete the installation and test the detector (figure 8):.
It 10 2csyd0201b figure 8 1) set the detector sensitivity (l = low, m = medium, h = high) with the proper selector. 2) set the dip switch of the detector (see the following table). 3) set the dip switch 1 of the detector to on (test mode). 4) lay the front cover back on the device and walk in the ar...
It 11 2csyd0201b during the self-recognition it is important that nothing (objects, people, etc.) is at a distance of less than 1 meter from the detector. Once the self-recognition has finished, the detector enters the “anti-masking test” mode for 10 minutes. During these 10 minutes if you try to ma...
It 12 2csyd0201b 4 maintenance 4.1 cleaning to clean the device externally, use a slightly wet cloth. Regularly check that the front lens is clean and that there are no obstacles. 4.2 test execute the detector test at least once a year. For the test procedure, please refer to the manual related to t...
It 13 2csyd0201b 5 technical specifiations application scope security communication technology transmission in fm 868.3 mhz range in free air 300 m power supply no. 1 lithium battery 3 v – 1.4 ah lasting 4 years (with 120-s. Suppression). Operation is guaranteed for 30 days from the low battery noti...
It 14 2csyd0201b 6 notes.
Manual code: 2csm600505d0 201 rev 00 abb s.P.A. – abb sace division viale dell’industria, 18 20010 vittuone (mi) for further information and assistance: from monday to saturday from 8:00 a.M. To 7:00 p.M. Printed in italy power and productivity for a better world tm.
