1. DL manuals
  2. ABC Office
  3. Paper Shredder
  4. IDEAL 4107
  5. Operating Instructions Manual

ABC Office IDEAL 4107 Operating Instructions Manual

Other manuals for IDEAL 4107: Operating Instructions Manual
Manual is about: ABC Office Paper Shredder Operating Instructions

Summary of IDEAL 4107

  • Page 1

    1 ideal 4107 ideal 4107 cc ideal 4109 ideal 4109 cc operating instructions.

  • Page 2

    2 ideal 4107; ideal 4109 1-800-658-8788 - www.Abcoffice.Com.

  • Page 3: Table of Contents

    3 table of contents 1. General ........................................................ 4 1.1 safety instructions ....................................... 4 1.2 application ................................................... 4 2. Installation ................................................... 5 2.1 ...

  • Page 4: 1. General

    4 ideal 4107; ideal 4109 1. General this instruction manual will help you to learn the safe and comfortable operation of this machine. Please carefully read and observe the operating instructions and safety instructions. This information applies to both models when no reference is made. After use pl...

  • Page 5: 2. Installation

    5 2. Installation the machine is mobile on castors. The machine must be installed on a sturdy, dry, and level floor. Oil level must be visible in the sight glass (2) ideal 4109 version. Danger! - the machine may not be installed outside. - do not use in the vicinity of flammable liquids or gases. - ...

  • Page 6

    6 ideal 4107; ideal 4109 2.2 power supply the name plate is located at the rear of the machine. - data stated on the name plate - voltage “ v “, - frequency “hz”, - power consumption “a” must correspond to the values of the power supply unit. - earth wire must be available. - connect the machine to ...

  • Page 7: 3. Operation

    7 3. Operation danger! The machine may only be operated by persons who have read and understood the operating instructions. Danger! Do not reach into the running shredding mechanism! The shredding mechanism may cause serious injury! Danger! The machine will only run when the door is closed. 3.1 oper...

  • Page 8

    8 ideal 4107; ideal 4109 machine stops due to overloading - remove any paper left on the conveyor belt. Do not reach behind the flap. - press and release the yellow key (3) ­ conveyor belt reverses. - feed less paper onto the conveyor belt. - start afresh. Machine stops and yellow lamp (3) lights (i...

  • Page 9

    9 3.5 oiling the shredding mechanism if the sheet capacity reduces or after “bag full“ we recommend that you oil the shredding mechanism. - press the oilpump button 3 x. - after lubrication let the machine run several times backwards and forwards alternately. - if tank (8) is empty refill with oil. ...

  • Page 10

    10 ideal 4107; ideal 4109 3.7 operation of baler (ideal 4109) eject bale when the white control lamp shows danger! Do not stand behind the bale ejecting guard during baling. ­ danger of being crushed. Bale ejection - release safety slide (1). (pull backwards and turn to the right). Danger! Do not st...

  • Page 11

    11 - hold bale ejecting guard (2) with the left hand and swing locking mechanism (4) with the right hand into vertical positon . . . . . . Until securing bushing (5) locks into position. - swing down bale ejecting guard (2). - press green button (6) until the pump motor switches off. ­ bale is eject...

  • Page 12

    12 ideal 4107; ideal 4109 - while removing the plastic bag push down the remaining paper. - place pressed bale on the floor. Danger! Do not reach into the hopper. ­ danger of getting cut! - tie bales or seal with locking device. (for sealing parts and binding wires see accessories). - press ball kno...

  • Page 13

    13 close bale - push up locking bush (5) and swing down locking mechanism (4). - slightly open the bale ejecting guard (2) with both hands until the lug (14) is above the locking catch (15). - hold bale ejecting guard with the left hand. Swing locking lever (2) with the right hand until it is almost...

  • Page 14

    14 ideal 4107; ideal 4109 - important! Lock safety slide (1). (pull back and turn up.). 3.8 premature ejecting of bale (ideal 4109) - push knob (16) with pen or similar. - further procedure as described in 3.7 “operation of baler“. 3.9 central lubrication (ideal 4109) - the baler is equipped with a ...

  • Page 15: 4. Trouble-Shooting

    15 4. Trouble-shooting danger! Disconnect from the mains before starting any service work or before removing the cover. Malfunction: standby (5) is not lighting up / machine does not start. Cause: - door / bale ejecting guard open - main switch “off“ - emergency button is pressed - key switch is ver...

  • Page 16: 5. Accessories

    16 ideal 4107; ideal 4109 5. Accessories plastic bags 350 l (50 pieces) 9000412 cutting head oil 10 x 0,2 l 9000610 for fastening plastic bags: wire twisting tool for one-way plastic bags 9000591 wire ties for one-way plastic bags (1000 pieces) 9000592 attention! Only use manufacturer recommended ac...

  • Page 17

    17 eg-konformit ÄtserklÄrung ec-declaration of conformity d éclaration de conformité ce declaraci ón ce de conformidad dichiarazione ce di conformit à eg-verklaring van overeenstemming declara çao ce de conformidade ef-overensstemmelseserkl æring - hiermit erkl ären wir, daß die bauart von - herewit...