Summary of I-S71
Page 1
I-s71 motherboard intel socket 775 installation guide.
Page 2
Ii i-s71 copyright and warranty notice the information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expre...
Page 3: Contents
I-s71 iii contents 1. Hardware setup ................................................ 1 1.1 specifications .............................................................1 1.2 choosing a computer chassis......................................2 1.3 installing motherboard....................................
Page 4
Iv i-s71.
Page 5
I-s71 1 1. Hardware setup 1.1 specifications cpu • lga775 socket for intel core 2 duo / pentium dual-core / pentium d / pentium 4 / celeron d processor with 800mhz fsb • supports intel hyper-threading technology chipset • sis 671 / 968 memory • 2x 240-pin dimm slots support up to 4gb capacity • supp...
Page 6
2 i-s71 1.2 choosing a computer chassis • choose a chassis big enough to install this motherboard. • as some features for this motherboard are implemented by cabling connectors on the motherboard to indicators and switches or buttons on the chassis, make sure your chassis supports all the features r...
Page 7
I-s71 3 1.4 checking jumper settings for a 2-pin jumper, plug the jumper cap on both pins will make it close (short). Remove the jumper cap, or plug it on either pin (reserved for future use) will leave it at open position. Short open open for a 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plu...
Page 8
4 i-s71 to renew the backup battery: 1. Power off the system and disconnect with ac power source. 2. Remove the exhausted battery. 3. Insert a new cr2032 or equivalent battery. Pay attention to its polarity. The “+” side is its positive polarity. 4. Connect ac power source and power on the system. 5...
Page 9
I-s71 5 1.5.2 front panel switches and indicators headers this header is used for connecting switches and led indicators on the chassis front panel. Watch the power led pin position and orientation. The mark “+” align to the pin in the figure below stands for positive polarity for the led connection...
Page 10
6 i-s71 1.6 installing hardware ※ do not scratch the motherboard when installing hardware. An accidental scratch of a tiny surface-mount component may seriously damage the motherboard. ※ in order to protect the contact pins, please pay attention to these notices: 1. A maximum 20 cycles of cpu instal...
Page 11
I-s71 7 5. Use your left hand to hold the load plate, and use your right thumb to peel the cap off. ※ the cap plays an important role in protecting contact pins. In order to prevent bent pin, put on the cap after operation or testing. 6. Lower the plate onto the cpu package. Engage the load lever wh...
Page 12
8 i-s71 1.6.2 ddr2 memory slots • install dimms with the same cas latency. To reach the optimum compatibility, obtain memory modules from the same vendor. ※ usually there is no hardware or bios setup required after adding or removing memory modules, but you will have to clear the cmos memory first i...
Page 13
I-s71 9 1.7 connecting peripheral devices 1.7.1 floppy and ide disk drive connectors connect the single end at the longer length of ribbon cable to the fdd on the board, the two connectors on the other end to the floppy disk drives connector. Generally you need only one floppy disk drive in your sys...
Page 14
10 i-s71 1.7.3 additional usb 2.0 port headers each header supports 2x additional usb 2.0 ports by connecting bracket or cable to the rear i/o panel or the front-mounted usb ports of your chassis. Pin pin assignment pin pin assignment 1 vcc 2 vcc 3 data0 - 4 data1 - 5 data0 + 6 data1 + 7 ground 8 gr...
Page 15
I-s71 11 1.7.5 front panel audio connection header this header provides the connection to audio connector at front panel. Pin signal name function 1 aud_mic front panel microphone input signal 2 aud_gnd ground used by analog audio circuits 3 aud_mic_bias microphone power 4 aud_vcc filtered +5v used ...
Page 16
12 i-s71 1.8 connecting rear panel i/o devices the rear i/o part of this motherboard provides the following i/o ports: • mouse: connects to ps/2 mouse. • keyboard: connects to ps/2 keyboard. • lpt1: connects to printer or other devices that support this communication protocol. • com1: connects to ex...
Page 17
I-s71 13 2. Bios setup this motherboard provides a programmable eeprom so that you can update the bios utility. The bios (basic input/output system) is a program that deals with the basic level of communication between processor and peripherals. Use the bios setup program only when installing mother...
Page 18
14 i-s71 3. Driver & utility the “driver & utility cd” that came packed with this motherboard contains drivers, utilities and software applications required for its basic and advanced features. Place the “driver & utility cd” into the cd-rom drive in your system. The following installation auto-run ...
Page 19
I-s71 15 4. Appendix 4.1 規格（繁體中文） 處理器 • 支援具備 800mhz 前端匯流排的 intel core 2 duo / pentium dual-core / pentium d / pentium 4 / celeron d 處理器 • 支援 intel hyper-threading 技術 晶片組 • sis 671 / 968 記憶體 • 2 條 240 針腳 dimm 插槽，支援最大 4gb 記憶體容量 • 支援單通道 ddr2 667 無緩衝非 ecc 記憶體 圖形埠 • 整合 sis mirage 3 dx9.0 gpu 網路 • 內建 10/1...
Page 20
16 i-s71 4.2 规格（简体中文） 处理器 • 支持具备 800mhz 前端总线的 intel core 2 duo / pentium dual-core / pentium d / pentium 4 / celeron d 处理器 • 支持 intel 超线程技术 芯片组 • sis 671 / 968 内存 • 2 条 240 针脚 dimm 插槽支持最大 4gb 内存容量 • 支持单信道 ddr2 667 无缓冲非 ecc 内存 图形端口 • 整合 sis mirage 3 dx9.0 gpu 网络 • 内建 10/100m 网络控制器 音效 • 支持 7.1 声道 hd 音...
Page 21
I-s71 17 4.3 troubleshooting (how to get technical support?) 4.3.1 q & a q: do i need to clear the cmos before i use a new motherboard to assemble my new computer system? A: yes, we highly recommend that you clear the cmos before installing a new motherboard. Please move the cmos jumper from its def...
Page 22
18 i-s71 example: memory brand: kingston (kvr533d2n4/1g) • memory size: type in the size of your memory module. Example: 512m* 4pcs • memory configuration: type in the memory configuration in bios setting. Example: memory timing: 2.5-3-3-7 @533mhz • graphics information: note graphics card’s brand, ...
Page 23
I-s71 19 4.4 contact information taiwan head office universal abit co., ltd. 6f, no. 323, yang guang st., neihu, taipei, 114, taiwan tel: 886-2-8751-3380 fax: 886-2-8751-3381 sales: sales@abit.Com.Tw marketing: market@abit.Com.Tw north america, south america universal abit (usa) corporation 2901 bay...
Page 24
P/n: 4310-0000-94 rev. 2.00 http://www.Abit.Com.Tw.