友旺科技 abocom mh1000 多路寬頻負載平衡器 multi-homing gateway quick install guide 快 速使 用 手 冊.
目錄 english qig .........................................................................................2 h ardware c onfiguration ....................................................................3 s oftware c onfiguration .....................................................................4 繁體安...
English qig 2.
Hardware configuration hardware description: power led: illuminates solid green when mh1000 is first powered up. Start up takes up to one minute to complete. status led: when led light start glittering, it means the system is under the status of booting. Around two minutes when the led light sto...
Software configuration step 1﹒connect both the administrator's pc and the lan port of mh1000 to a hub or switch. And use a web browser to display the configurations of the mh1000 (such as internet explorer or netscape). The default ip address of mh1000 is http://192.168.1.1 with a subnet mask of 255...
a pop-up screen will appear and prompt for a username and password. A username and password is required to connect to mh1000. Enter the default login username and password of administrator (figures-1). username: admin password: admin click ok. Figures-1 login webui step 4﹒after entering the us...
Step 6﹒after entering to the main system of mh1000, select interface on the left menu and click on wan. (figure s-3) figures-3 wan 1/2 interface step 7﹒wan interface 1 / 2: select the wan 1/2 that needs to be set and click modify. Enter the ip address provided from isp. (figure s-4) figure s-4 wan i...
Step 8﹒click on system function and click on date/time function in configure. Step 9﹒enter the following setting in date/time setting: select enable synchronize with an internet time server. Set offset +8 hours from gmt enter the server ip/name: 133.100.9.2 enter update system clock every 360 minu...
Step 10﹒click on policy on the left function menu and then click on outgoing from the sub-function list. Step 11﹒click new entry (figure s-6) step 12﹒at add new policy webui, enter the following information: source address – select “inside_any” destination address – select “outside_any” action: se...
繁體安裝 9.
Mh1000 硬體安裝 mh1000 硬體外部介面說明: 圖 h-1 mh1000 接孔、指示燈說明 power led : 電源顯示 status led:當 led 燈為開始閃爍時,表示系統正在開機狀態, 約兩分鐘後系統開機程序結束,當 led 停止閃爍,表示系統己開 機成功。 wan 1 / 2 port:外部網路介面 1 / 2,與外部路由器連結。 lan:內部網路介面,將企業內部的網路連結在此網路。 dmz:非軍事區網路介面,將企業內的伺服器連結在此網路。 console port:9-pin 的串列埠接頭,主要的用途是查看 mh1000 系統環境參數。 10
Mh1000 軟體設定 步驟 1. 首先將系統管理員的電腦和mh1000 內部網路介面接到同一個hub 或switch,再使用瀏覽器 ( ie或 netscape ) 連結至mh1000。 mh1000 內部網路介面的ip位址內定值為 http://192.168.1.1 ,所以系 統管理員的電腦之ip位址必須是 192.168.1.2 至 192.168.1.254 其中 之一,子網路遮罩為 255.255.255.0。 步驟 2. 當管理員的電腦和mh1000 的內部網路介面位址 屬於 192.168.1.0 網 段 的 網 路 , 開 啟 瀏 覽 器 ( ie 或 netscape ) ...
步驟 3. 瀏覽器會詢問使用者名稱及密碼,輸入管理員名稱與密碼。 (如圖 s-1 ) 使用者名稱:admin 密碼:admin 點選【確定】 圖 s-1 鍵入使用者名稱與密碼 步驟 4. 進入 mh1000 軟體系統主畫面後,在左方的功能選項中,點選【介 面位址】功能,再點選【內部網路】次功能選項。 (如圖 s-2 ) 內部網路 ip 位址:192.168.1.1 子網路遮罩:255.255.255.0 點選【確定】 圖 s-2 鍵入內部網路 ip 位址與子網路遮罩 步驟 5. 如果新的內部網路介面位址不是 192.168.1.1。在點選【ok】後,必 須更改系統管理員的 ip...
步驟 . 6 進入 mh1000 軟體系統主畫面後,在左方的功能選項中,點選【介 面位址】功能,再點選【外部網路】次功能選項。 (如圖 s-3 ) 圖 s-3 外部網路介面 1 / 2 介面 步驟 7. 外部網路介面 1 / 2:點選需要設定的外部網路 1 / 2 , 點選【修改】選項。鍵入由 isp 所配發的 ip 位址 (如圖 s-4 ) (例:外部網路介面位址 1) 外部網路路介面位址 1: ip 位址 :61.11.11.11 子網路遮罩: 255.255.255.0 預設閘道: 61.11.11.254 dns 伺服器 1: 168.95.1.1 圖 s-4 鍵入外部網路 ip ...
步驟 8. 在左方的功能選項中,點選【系統管理】功能,再點選【組態】【時 間設定】次功能選項。 步驟 9. 在出現的【時間設定】視窗中,鍵入下列相關參數: 勾選【開啟與外部時間伺服器同步】 選擇與 gmt 相差【+8】小時。(依所在地決定) 輸入時間伺服器位址【133.100.9.2】 輸入系統自動更新時間【360】分鐘 按下【確定】,完成時間設定。 (如圖 s-5 ) 圖 s-5 時間設定 14.
步驟 10. 在左方的功能選項中,點選【管制條例】功能,再點選【內部至外部】 次功能選項。 步驟 11. 點選螢幕下方的【新增】管制條例功能按鈕。 (如圖 s-6 ) 步驟 12. 在出現的【新增管制條例】視窗中,鍵入下列相關參數: 來源網路位址:選擇【inside_any】 目的網路位址:選擇【outside_any】 管制動作:選擇【允許】 按下【確定】鈕。 圖 s-6 至管制條例功能設定來源網路位址與目的網路位址 步驟 . 13 如欲使用 mh1000 的管制功能,請在【位址表】和【管制條例】功 能項增加相關設定值。 15.
简体安装 16.
Mh1000 硬件安装 mh1000 硬件外部接口说明: 图 h-1 mh1000 接孔、指示灯说明 power led : 电源显示 status led:当 led 灯为开始闪烁时,表示系统正在开机状态, 约两分钟后系统开机程序结束,当 led 停止闪烁,表示系统己开 机成功。 wan 1 / 2 port:外部网络接口 1 / 2,与外部路由器连结。 lan:内部网络接口,将企业内部的网络连结在此网络。 dmz:非军事区网络接口,将企业内的服务器连结在此网络。 console port:9-pin 的串行埠接头,主要的用途是查看 mh1000 系统环境参数。 17.
Mh1000 软件设定 步骤 1. 首先将系统管理员的计算机和mh1000 内部网络接口接到同一个 hub或switch,再使用浏览器 ( ie或 netscape ) 连结至mh1000。 mh1000 内部网络接口的ip地址内定值为 http://192.168.1.1 ,所以系 统管理员的计算机之ip地址必须是 192.168.1.2 至 192.168.1.254 其 中之一,子网掩码为 255.255.255.0。 步骤 2. 当 管 理 员 的 计 算 机 和 mh1000 的 内 部 网 络 接 口 地 址 属 于 192.168.1.0 网段的网络,开启浏览器(ie或netsc...
步骤 3. 浏览器会询问使用者名称及密码,输入管理员名称与密码。 (如图 s-1 ) 使用者名称:admin 密码:admin 点选【确定】 图 s-1 键入使用者名称与密码 步骤 4. 进入 mh1000 软件系统主画面后,在左方的功能选项中,点选【接 口地址】功能,再点选【内部网络】次功能选项。 (如图 s-2 ) 内部网络 ip 地址:192.168.1.1 子网掩码:255.255.255.0 点选【确定】 图 s-2 键入内部网络 ip 地址与子网掩码 步骤 5. 如果新的内部网络接口地址不是 192.168.1.1。在点选【ok】后,必 须更改系统管理员的 ip 地...
步骤 . 6 进入 mh1000 软件系统主画面后,在左方的功能选项中,点选【接 口地址】功能,再点选【外部网络】次功能选项。 (如图 s-3 ) 图 s-3 外部网络接口 1 / 2 接口 步骤 7. 外部网络接口 1 / 2:点选需要设定的外部网络 1 / 2 , 点选【修改】选项。键入由 isp 所配发的 ip 地址 (如图 s-4 ) (例:外部网络接口地址 1) 外部网络路接口地址 1: ip 地址 :61.11.11.11 子网掩码: 255.255.255.0 预设网关: 61.11.11.254 dns 服务器 1: 168.95.1.1 图 s-4 键入外部网络 ip 地...
步骤 8. 在左方的功能选项中,点选【系统管理】功能,再点选【组态】【时 间设定】次功能选项。 步骤 9. 在出现的【时间设定】窗口中,键入下列相关参数: 勾选【开启与外部时间服务器同步】 选择与 gmt 相差【+8】小时。(依所在地决定) 输入时间服务器地址【133.100.9.2】 输入系统自动更新时间【360】分钟 按下【确定】,完成时间设定。 (如图 s-5 ) 图 s-5 时间设定 21.
步骤 10. 在左方的功能选项中,点选【管制条例】功能,再点选【内部至外部】 次功能选项。 步骤 11. 点选屏幕下方的【新增】管制条例功能按钮。 (如图 s-6 ) 步骤 12. 在出现的【新增管制条例】窗口中,键入下列相关参数: 来源网络地址:选择【inside_any】 目的网络地址:选择【outside_any】 管制动作:选择【允许】 按下【确定】钮。 图 s-6 至管制条例功能设定来源网络地址与目的网络地址 步骤 . 13 如欲使用 mh1000 的管制功能,请在【地址表】和【管制条例】功 能项增加相关设定值。 22.