Summary of Modem UTM560
Page 1
Usb v.90 tiny modem quick installation guide.
Page 2: Fcc Regulatory Statements
Fcc regulatory statements the united states federal communication commission (fcc) and the canadian department of communications have established certain rules governing the use of modems and other electronic equipment. Fcc part 68 registration this high speed usb 56k fax/modem complies with fcc par...
Page 3
This equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate...
Page 4: Table of Contents
Table of contents introduction .............................................................1 s pecifications .....................................................1 modem ...............................................................1 fax................................................................
Page 5: Introduction
Introduction the usb v.90 tiny modem complies with the universal serial bus functionality built in windows 98/2000/millennium. It is compatible with bell, itu-t (formerly ccitt) and hayes at commands. The usb v.90 tiny modem enables you enjoy all the benefit offered by usb technology and get a faste...
Page 6: System Requirements
- 2 - system requirements a pentium processor-based personal computer 166mmx or above at least 16 mb of ram an usb port microsoft windows 98/2000/millennium a cd-rom drive.
Page 7: Hardware Installation
Hardware installation 1. Locate the usb host port of your system. Connects the usb type a connector to the usb host port on your computer. 2. Connects the phone line to the phone line jack - 3 -.
Page 8: Software Installation
Software installation installation for windows 98 1. When the usb v.90 tiny modem is well connected to your computer, windows 98 will automatically detect the new device. Click next. 2. Select search for a suitable driver for my device (recommended) and click next. - 4 - 3. Insert the device driver ...
Page 9: Next.
- 5 - you load the device driver.Click next. Windows will start searching for the appropriate driver for the software installation. 4. Click next. 5. Click finish. The software installation is successfully completed. 6. When the following dialog box appears, select the country/location where you are...
Page 10: Setup Diagnostics
- 6 - setup diagnostics you can perform the following steps to check if your usb v.90 tiny modem is well installed. 1. Go to start →settings→control panel→modems. 2. When the modems properties dialog box appears, select the diagnostics tab. 3. Select usb v.90 tiny modem and click ok. 4. If usb v.90 ...
Page 11: Next.
Installation for windows 2000 1. Once the usb v.90 tiny modem is well connected to your computer, windows 2000 will automatically detect the new device. Click next. 2. Select search for a suitable driver for my device (recommended) and click next. 3. Insert the device driver compact disc into the cd...
Page 12: Next To Continue.
- 8 - 4. Click browse button and select the drive where you load the device driver (for example: g:\win2k). Click ok. Windows will start searching for the appropriate driver for the software installation. 5. Click next to continue. 6. Click yes. 7. Click finish. 8. When windows prompt you “modem cou...
Page 13: Setup Diagnostics
- 9 - setup diagnostics to verify whether your usb v.90 tiny modem exists in your computer and is enabled, go to my computer →control panel→system. Click the device manager tab. If the usb v.90 tiny modem and network adapters are found, it means that your network device is well installed. If not, co...
Page 14: And Click Next.
Installation for windows millennium 1. When the usb v.90 tiny modem is well connected to your computer, windows me will automatically detect the new device. Select specify the location of the driver (advanced) and click next. 2. Load the device driver compact disc into the cd-rom of your system and ...
Page 15: (Advanced) And Click Next.
- 11 - 3. Expect a minor delay for windows to search for the appropriate driver for the device. Click next. 4. Click finish. The installation program will continue. 5. Select specify the location of the driver (advanced) and click next. 6. When the above figure appears, repeat step 2, namely, select...
Page 16: Next.
- 12 - 7. Click next. 8. When windows prompt you “modem country selection”, choose the country where you locate. Select the enable pbx check box and click ok. 9. Click finish to complete the installation..
Page 17: Setup Diagnostics
Setup diagnostics 1. To verify if the usb v.90 tiny modem is well installed and enabled, you can perform the following steps. 2. Go to start settings control panel modems. 3. When the modems properties dialog box appears, select the diagnostics tab. 4. Highlight usb v.90 tiny modem and click the mor...
Page 18: Internet Access
Internet access 1. Go to my computer. 2. Select dial-up networking. 3. Double-click make a new connection, a dialogue box will appear for you to name the new connection and select the device. Name the new connection appropriately and click next. 4. Enter the area code and phone number of your intern...
Page 19
- 15 - 7. Now, you are ready to connect to the internet..