ABS ABT-2020MP Owner's Manual

Summary of ABT-2020MP

  • Page 1

    Part number 20079, rev 0 1 premiere solid door freezers abt-2020mp, abt-2030mp, abt-3020mp, abt-3030mp, abt-3020ap owner’s instructions this manual describes how to operate and care for your appliance to get the best, most efficient, performance. Read this book! Note to customer: this merchandise wa...

  • Page 2

    Part number 20079, rev 0 2 table of contents receiving ............................................................................................................. 3 installation ........................................................................................................ 4 freezer opera...

  • Page 3

    Part number 20079, rev 0 3 receiving your unit was built, packaged, and inspected with extreme care. We shipped it to you using carriers we trust with a proven track record of careful handling, good customer service, and on time delivery. Unfortunately, regardless of all of these efforts sometimes a...

  • Page 4

    Part number 20079, rev 0 4 installation uncrating – this unit comes with an optional roller base so you can unpack it in an open area and then place it on the roller base to move to its normal location. Remove the wooden planks or skid as shown. These units come with a caster platform (or roller bas...

  • Page 5

    Part number 20079, rev 0 5 it has started cycling normally before placing product in the cabinet. The motor compressor may start and stop several times when the unit is first started or after defrosting, especially if the weather is very hot. This is normal. The motor compressor will cycle normally ...

  • Page 6

    Part number 20079, rev 0 6 freezer operation after the unit is properly installed and power is applied, it will take some time before the system is cooled down to temperature and cycling normally. You should wait 8 hours on the first startup before beginning to add product to the unit. This ensures ...

  • Page 7

    Part number 20079, rev 0 7 control center -- temperature monitor system the temperature control center (monitor) system on the front of the unit provides the following functions- - to provide an indication of the sample temperature inside of the compartment - to provide a local alarm at the unit in ...

  • Page 8

    Part number 20079, rev 0 8 the status tricolor led shows the status of the unit. Green = normal run mode amber = program mode red = temperature is out of range (the light blinks off briefly each second to show the unit is active) the alarm/test push-button interrupts line power, to allow testing of ...

  • Page 9

    Part number 20079, rev 0 9 b asic o peration the control center monitor has two modes: normal run mode and programming mode. In normal run mode, the display shows the temperature that the probe is reading to the lowest whole number, i.E., if it shows a value of 10.0ᵒ, the actual temperature can rang...

  • Page 10

    Part number 20079, rev 0 10 testing the battery: the battery recharges when the unit is plugged into line power. To test the battery, push the alarm/test button on the front panel. The following should happen: • the alarm led will flash red. • the beeper alarm will begin to chirp. • the remote alarm...

  • Page 11

    Part number 20079, rev 0 11 rd (relay delay) if there is an alarm condition, the relay contacts will switch. The relay delay parameter allows the user to set the amount of time delay from the start of the alarm condition to the time the relay contact switches. This keeps the relay from switching dur...

  • Page 12

    Part number 20079, rev 0 12 digital microprocessor temperature controller product description the digital microprocessor temperature controller is designed to provide on/off control of refrigerators or freezers. The controller also provides a constant readout of the air temperature inside of the uni...

  • Page 13

    Part number 20079, rev 0 13 programming procedure display description display to start programming, press the set key once to access the fahrenheit / celsius mode. The display shows the current status, f for fahrenheit or c for celsius. Press up or down arrow to toggle between the f or c. F or c fah...

  • Page 14

    Part number 20079, rev 0 14 error messages display messages corrective action e1 appears when either the up or down key is pressed when not in the programming mode if the e1 message appears even when no keys are being pressed, replace control. E2 appears if the control settings are not properly stor...

  • Page 15

    Part number 20079, rev 0 15 quick troubleshooting guide check these items before calling for service problem: possible cause / soultions: unit does not run • electrical circuit is not 110-120v 60hz. • the power cord is not plugged in. • no power at electrical outlet. Check to make sure breaker is no...

  • Page 16

    Part number 20079, rev 0 16 problem: possible cause / soultions: compressor noises • compressor may be overheated. Please check the room temp and ensure the range is within 65°f to 85°f. If the problem still exists, call for service. Moisture collects inside • door gasket is not sealing properly. Ch...

  • Page 17

    Part number 20079, rev 0 17 maintenance and cleaning manual-defrost freezers (all models except abt-3020ap) should be defrosted whenever ¼ to ½ inch of frost has accumulated. Use the procedures in the defrosting section starting at the bottom of this page for best results. They should also be cleane...

  • Page 18

    Part number 20079, rev 0 18 instrument to remove frost. Never use a damp cloth or wet hands as they will stick to the inside surfaces when cold. When defrosting becomes necessary, disconnect freezer from power source by unplugging to avoid electrical hazard. Do not adjust the thermostat. Remove the ...

  • Page 19

    Part number 20079, rev 0 19 horizon scientific, inc. Product warranty horizon scientific, inc. Warrants to the original purchaser every new horizon scientific, inc. Refrigerated unit, the cabinet and all parts thereof, to be free from defects in material or workmanship, when such unit is installed, ...

  • Page 20

    Part number 20079, rev 0 20 warranty is not transferable. This warranty is not assignable and applies only in favor of the original purchaser/user to whom delivered. Any such assignment or transfer shall void the warranties herein made and shall void all warranties, express or implied, including any...