Summary of X8S
Page 1
Page 1 abtronic™x86s fitness belt user manual.
Page 2: Page 2
Page 2 abtronic™x8s fitness belt congratulations on your choice of the abtronic™x8s fitness belt. Please read this manual before first use. Controls a self-timer switches the unit off after 10 minutes. Program button to change 6 programs on/+ button, increase intensity off/- button, decrease intensi...
Page 3: Page 3
Page 3 abtronic™x86s fitness belt 1. On/+ : turns the unit on and increases the output intensity. Press once to increase the output intensity. The higher the intensity - the larger the contraction. To adjust to maximum output power you need to push this button 10 times. 2. Off/- : each pressing of t...
Page 4: Page 4
Page 4 abtronic™x8s fitness belt operation battery 1. Open the battery door by pushing it in the direction of the arrow: 2. Insert one piece cr 2032 lithium battery into the battery compartment. The positive “+” pole of the battery should be facing you..
Page 5: Page 5
Page 5 abtronic™x86s fitness belt basic use 1. Attach the abtronic™x8s control unit onto the x silicon pad holder. Insert the controller by aligning the marking on the controller case with the holder: insert the control unit aligning it with the shorter marking on the holder at position (1) and turn...
Page 6: Page 6
Page 6 abtronic™x8s fitness belt do not use damaged, worn or dirty gel sheets as this might result in burns. Always, stick gel sheets to all electrodes while using the product. Don’t apply the product directly to skin, this may be painful or cause irritation or burns. Precautions applying gel sheets...
Page 7: Page 7
Page 7 abtronic™x86s fitness belt 3. After affixing all gel sheets properly, peel off the remaining film, which has wording, and ready to stick on your skin do not peel off the gel sheet affixed to the electrode, until you need to replace them with new ones! 4. Gel sheet storage after use, do not re...
Page 8: Page 8
Page 8 abtronic™x8s fitness belt removing gel sheets 1. Only remove the gel sheets if you need to replace them with new ones. 2. Turn off the product before removing the gel sheet. Otherwise this may cause pain or irritation. 3. Peel off the complete gel sheet slowly in one piece. • remove any remai...
Page 9: Page 9
Page 9 abtronic™x86s fitness belt control unit: 1. Press the on/+ button to power up the abtronic™x8s control unit. 2. Select the mode by pressing the “mode” button repeatedly. Every time you press the “mode” button a different led or combination will light up indicating one of the 6 preprogrammed r...
Page 10: Page 10
Page 10 abtronic™x8s fitness belt if you do not feel any stimulation reposition the product 1-2 cm at a time up or down, until you find the trigger points for the muscle stimulation. Please turn the unit off before repositioning! Hint: do not use gel or creams that contain oils with the product. 3. ...
Page 11: Page 11
Page 11 abtronic™x86s fitness belt 4. The intensity has 10 steps. With every push of the button on/+ you increase the intensity by one step, with every push of the button off/- you decrease the intensity by one step. To switch the unit off, press the off/- button several times, until the led lights ...
Page 12: Page 12
Page 12 abtronic™x8s fitness belt what to do if you do not feel the stimulation should no stimulation or contraction be felt, move the belt slowly around the area on your stomach. Please turn the unit off before moving it to a new position. The abtronic™x8s is a great way to exercise your muscles. I...
Page 13: Page 13
Page 13 abtronic™x86s fitness belt taking care of your unit the abtronic™x8s is made of quality materials. The only maintenance required with the abtronic™x8s is to clean the conductive area gently, while you are replacing the gel sheets, with a wet cloth and soapy water, further the battery needs t...
Page 14: Page 14
Page 14 abtronic™x8s fitness belt important – please read if the gel sheets are worn out, or dirty, an uncomfortable tingling sensation can occur. This can also happen if the body has built up excessive oil on the skin. Do not bend the conductive areas. Worn or dirty conductive gel sheets can reduce...
Page 15: Page 15
Page 15 abtronic™x86s fitness belt a. As long as the gel sheets are not worn or dirty and are kept firmly against the skin you will not feel any unpleasantness. At low intensity you will feel a slight tingling sensation but as the intensity gets higher you will only feel the pleasant contraction. St...
Page 16: Page 16
Page 16 abtronic™x8s fitness belt contraindications abtronic™x8s should not be used by people, with cardiac pacemaker, defibrillator or other implanted electronic or metallic devices. Abtronic™x8s should not be used by pregnant women, and during first 6 weeks after their baby’s birth. Abtronic™x8s s...
Page 17: Page 17
Page 17 abtronic™x86s fitness belt transcerebrally (through the head) over swollen, infected or inflamed areas of skin eruptions (e.G., phlebitis, thrombophlebitis, varicose veins, etc.) transthoracically; introduction of electrical current into the heart may cause rhythm disturbances, which could b...
Page 18: Page 18
Page 18 abtronic™x8s fitness belt precautions / do not use when: 1. Do not use if there is tendency to hemorrhage (acute trauma or fracture). 2. Do not use following any recent surgical procedure when muscle contraction may disrupt the healing process. 3. Do not use over the menstruating uterus. 4. ...
Page 19: Page 19
Page 19 abtronic™x86s fitness belt trouble shooting guide problem possible cause solution leds do not light up at all batteries are not installed batteries are installed incorrectly. Batteries are empty install batteries check polarity “+” sign replace batteries leds light up, but nothing happens no...
Page 20: Page 20
Page 20 abtronic™x8s fitness belt leds light up, but nothing occurs intensity set to low level worn or dirty gel sheets. Abtronic™ is positioned incorrectly gel sheets are worn or have oil deposits. Battery is low increase intensity by pushing the up button make sure the gel sheets are still adhesiv...
Page 21: Page 21
Page 21 abtronic™x86s fitness belt specification channel: single channel program modes 6 program modes intensity control: adjustable 0-28ua, max output 28ua peak to peak into 10k ohm load each channel. Wave form asymmetrical bi-phase square pulse out voltage adjustable 0-168v, max output 168v peak t...
Page 22: Www.Abtronic.Co
This product is brought to you by: abtronic by red lemon incorporation www.Abtronic.Co www.Red-lemon.Com © by red lemon incorporation mmxv rlx8sengv1.2.