- DL manuals
- Abus
- Security Camera
- TVCC50030
- User Manual
Abus TVCC50030 User Manual
Summary of TVCC50030
Page 1
23 wdr dnr day/night 650 tvl camera profiline version 07/2010 original english user manual. Keep for future use. Tvcc50030 tvcc50530
Page 2
24 Ŝ introduction dear customer, thank you for purchasing this product. This product meets the requirements of the applicable european and national guidelines. The corresponding declarations and documents can be obtained from the manufacturer (www.Abus-sc.Com). To maintain this condition and to ensu...
Page 3
25 important safety instructions the warranty will expire for damage due to non-compliance with these operating instructions. We shall not be liable for any consequential loss! We do not accept liability for damage to property or personal injury caused by incorrect handling or non-compliance with th...
Page 4
26 table of contents 1. Intended use .......................................................................................................... 27 2. Explanation of symbols .................................................................................. 27 3. Scope of delivery .......................
Page 5
27 1. Intended use the wdr dnr day/night 650 tvl camera profiline is equipped with a high quality image sensor. It is used for video surveillance in internal areas in connection with a recorder or monitor. You can find a detailed description of functions in section “4. Features and functions”. The p...
Page 6
28 5. Description of device 5.1 overview – article numbers article number tvcc50030 tvcc50530 resolution 650 tvl 650 tvl wdr dnr 2d/3d-dnr 2d/3d-dnr day/night (removable ir cut-filter) operating voltage 12vdc/24vac 110-240vac 5.2 unpacking while you are unpacking the device please handle it with utm...
Page 7
29 6.2 lens mounting the camera is designated for lenses with cs-mount. A lens with c-mount can be mounted with the enclosed lens adapter ring. Before a lens with c-mount can be mounted, please make sure that the lens adapter ring is mounted on the camera. Otherwise you may damage the image sensor. ...
Page 8
30 7. Rear view 12vdc variante 110~240vac variante (1) osd menu buttons (2) relay output (triggered by motion, max. 60vdc/400ma) (3) power supply (12vdc/24vac or 110~240vac) (4) status led (active if power is connected) (5) bnc video output (monitor) (6) bnc video output (video) buttons function (1)...
Page 9
31 8. On screen display (osd) function description quick install fast setup of the most important parameters advanced menu detailed setup of all camera parameters exit leave the main menu completely. Quick install for an easy configuration of this camera the function „quick install“ was implemented....
Page 10
32 focus adjust the function „focus adjust“ is used to be able to setup the image focus perfectly. The lens aperture will be set to maximum in this mode. To move to the next step inside “quick install” please activate the menu item “next” in the on-screen-display. Using “back” you move to the previo...
Page 11
33 advanced menu advanced menu exposure wd.. White balance atw enhance .. D/n auto .. Detect off miscellaneous .. Restore default back exit function description exposure settings for camera exposure mode white balance settings for white balance mode enhance settings for picture improvement day / nig...
Page 12
34 changing illumination conditions. Only auto iris lenses can be used in this mode. Shutter (auto, 1/50~1/10000) auto : automatic control of the exposure time 1/5~1/10000 : fixed exposure time to be selected (1/50 – slow, 1/10000 – fast) blc (on/off) on : backlight compensation on off : backlight c...
Page 13
35 white balance function description atw auto tracking white balance the white balance will be performed dynamically and continuously in a range of 1800~10500k. Awb auto white balance the white balance is performed once at a restart of the camera. Ptl push to lock the white balance will be performe...
Page 14
36 off : image integration deactivated 2x~128x : image integration activated at selected integration rate. The image integration will be only active in low light conditions. Dnr digital noise reduction, dnr off : digital noise reduction deactivated 2d dnr : digital noise reduction optimized for stat...
Page 15
37 detection setup (detect) function description off all detection function of the camera are deactivated. Motion the motion detection of the camera is active and can be further configured. There are 8x8 field available for marking the detection area. L/r move : the frame to mark a field can be move...
Page 16
38 miscellaneous misc menu mirror off mask .. Camera id off winker off e-zoom off back exit function description mirror mirror of the image off : mirror deactivated h : horizontal mirror activated v : vertical mirror activated h/v : horizontal and vertical mirror activated mask settings for privacy ...
Page 17
39 winker live image verification the function „winker“ will realize a live image verification, this is done by a blinking sign in the live image. Off : live image verification deactivated on : live image verification activated e-zoom digital zoom the center of the image can be magnified digitally, ...
Page 18
40 9. Servicing and cleaning 9.1 function test check the technical safety of the product such as damage to the housing at regular intervals. When it can be assumed that the safe operation is no longer possible, the product must be put out of service and precautions taken o ensure that it is not used...
Page 19
41 11. Technical data article number tvcc50030 tvcc50530 videosignal pal resolution 650 tvl 650 tvl image sensor 1/3" sony interline super had ii dual scan ccd dsp sony effio picture elements (total) 1028(h) x 596 (v) picture elements (effective) 976(h) x 582 (v) signal-to-noise ratio 50 db minimum ...
Page 20
42.