Summary of Aqua Drum EO
Page 1
User guide www.Acclaimlighting.Com aqua drum.
Page 3
1 www.Acclaimlighting.Com contents introduction ......................................................2 welcome 2 safety 2 installation .........................................................3 aqua driver 150 mounting 3 control input connections 3 creating a wireless dmx input 4 converting a 0-10v...
Page 4
2 www.Acclaimlighting.Com introduction welcome welcome to the aqua drum (and aqua driver 150) from acclaim lighting. This range of high output, submersible led flood fixtures offer ip68* submersible properties thanks to their 316 marine grade stainless steel housings and fully sealed joints. There a...
Page 5
3 www.Acclaimlighting.Com installation aqua driver 150 mounting the aqua driver 150 can be wall mounted either vertically or horizontally as required. Two slotted holes (Ø 0.23” x 0.47” / Ø 6 x 12mm) are available on each side for mounting purposes - see “dimensions” on page 19. Control input connec...
Page 6
4 www.Acclaimlighting.Com dmx in dmx tx rx 0-10v in dmx creating a wireless dmx input the optional acclaim lighting aria units allow you create a wireless dmx link up to 2600 feet (792m) line of sight, between your control output and the aqua driver. Setup and configuration is straightforward: 1 con...
Page 7
5 www.Acclaimlighting.Com output connections the aqua driver 150 has four constant current output ports, each of which uses an 8-pin terminal block. Each output port provides multiple channels, the addressing of which are decided by the front panel switch settings (see “aqua driver 150 mode control”...
Page 8
6 www.Acclaimlighting.Com eo or so eo or so eo or so eo or so eo or so eo or so ho ho ho aqua drum fixture support the aqua driver 150 has four output ports to which varying numbers of aqua drum fixtures can be connected. Aqua drum eo and so fixtures require one port per fixture, whereas the larger ...
Page 9
7 www.Acclaimlighting.Com r+ r– g+ g– b+ b– w+ w– brown red black green gray blue yellow white 1 2 3 4 5 6 7 8 brown red black green gray blue yellow white 1 2 3 4 5 6 7 8 w+ w– w+ w– w+ w– w+ w– connector pin outs aqua drum ho rgbw/a these fixtures with 36 emitters require two 8-pin connections: co...
Page 10
8 www.Acclaimlighting.Com port grouping the four output ports can either be used individually under separate control or grouped in either pairs, or grouped all as one control block. The grouping status is determined by switches 1 and 2 of the smaller switch block (see page 11). Aqua drum ho fixtures...
Page 11
9 www.Acclaimlighting.Com dmx channel layouts the number of dmx channels required to control the connected fixtures depends upon the following settings, which are configured using the small switch block: • port grouping, and • fixture type the various dmx channel requirements for the various port gr...
Page 12
10 www.Acclaimlighting.Com power input the fixed power cord is supplied as standard with us color coding and bare tails. For international installations, wire according to local codes. Power cord colors the red front panel indicator will illuminate when power is applied. The other two indicators loc...
Page 13
11 www.Acclaimlighting.Com 9 6 3 8 5 2 10 7 4 1 256 128 64 32 16 dmx mode: on 8 dmx address 4 2 1 on aqua driver 150 mode control the manner in which the four output ports are grouped and operate is determined by the settings of the two switch blocks located on the front panel (note: all switch sett...
Page 14
12 www.Acclaimlighting.Com standalone mode: off 9 6 8 10 7 on standalone mode using internal chase programs in standalone mode, all four ports are treated as one group. Note: all switch settings can be changed when the driver is off or on. To configure the aqua driver 150 for standalone chase mode y...
Page 15
13 www.Acclaimlighting.Com standalone mode: off 9 6 8 10 7 on standalone mode using adjustable static dimming in standalone mode, all four ports are treated as one group. Note: all switch settings can be changed when the driver is off or on. To configure the aqua driver 150 for standalone static dim...
Page 16
14 www.Acclaimlighting.Com mounting surface installation to mount an aqua drum onto a surface may require you to first remove the yoke in order to gain full access to the mounting holes. 1 using a 3/16 (5mm) allen wrench, loosen the two yoke tensioners; it is not necessary to remove them completely....
Page 17
15 www.Acclaimlighting.Com grade french drain stone/gravel concrete waterproof j-box waterproof conduit aqua drum fixture with front plate attached plastic sleeve ground installation use an optional in-grade housing kit when installing an aqua drum in-ground; three sizes of sleeve kit are available ...
Page 18
16 www.Acclaimlighting.Com preparing the aqua drum for ground installation 1 on the underside of the aqua drum fixture, use a 1/8” (2.5mm) allen wrench to remove the four (six on ho models) bolts which secure the front ring: remove the standard front ring four (or six) x 1/8” (2.5mm) hex head bolts ...
Page 19
17 www.Acclaimlighting.Com 4 make the necessary connections within the well and test. 5 lower the aqua drum fixture into the well and align the four countersunk screw holes with the pilot holes in the top lip of the plastic sleeve: 6 insert the four supplied screws and use a ta2.3mm triangular drive...
Page 20
18 www.Acclaimlighting.Com further information aqua drum and driver specifications aqua drum fixtures emitters eo: 8 leds so: 18 leds ho: 36 leds photometrics (4000k) eo: 700 lm so: 1600 lm ho: 3259 lm power consumption eo: 8w so: 18w ho: 36w lumen maintenance (l 70 ) 150,000 hours (25 o c) operatin...
Page 21
19 www.Acclaimlighting.Com dimensions aqua driver 150 aqua driver 150 Ø0.24 x 0.47" ( 6 x 12mm) Ø 10.24" (260mm) 11.83" (300.5mm) 11.04" (280.5mm) 4.72" (120mm) 2.6" (66mm) 5.87" (149mm) weight: 2.6 lbs (1.18 kg).
Page 22
20 www.Acclaimlighting.Com dimensions aqua drum eo Ø4.92" (125mm) Ø3.66" (93mm) 2.42" (61.7mm) 5.43" (138mm) 1.26" (32mm) 1.26" (32mm) 4.72" (120mm) 5.71" (145mm) 1 x 0.41 ( 10.5mm) Ø Ø 2 x 0.24 ( 6mm) Ø Ø 1.5“ (38mm) fixture weight: 4 lbs (1.8 kg).
Page 23
21 www.Acclaimlighting.Com dimensions aqua drum eo in-grade housing kit Ø3.66" (93mm) Ø6.22" (158mm) Ø6.14" (156mm) 4.16" (105.7mm) 5.12" (130mm) 5.91" (150mm) 0.67" (17mm) 0.55" (14mm) 0.51" (13mm) 0.12" (3mm).
Page 24
22 www.Acclaimlighting.Com dimensions aqua drum so Ø5.16" (131mm) Ø6.53" (166mm) 2.42" (61.7mm) 7.04" (179mm) 1.57" (40mm) 6.33" (161mm) 7.28" (185mm) 1.57" (40mm) 1 x 0.43 ( 11mm) Ø Ø 2 x 0.35 ( 9mm) Ø Ø 1.85“ (48mm) fixture weight: 6.6 lbs (3 kg).
Page 25
23 www.Acclaimlighting.Com Ø7.76" (197mm) Ø5.16" (131mm) Ø7.83" (199mm) 5.12" (130mm) 6.61" (168mm) 7.64" (194mm) 0.67" (17mm) 0.55" (14mm) 0.57" (14.5mm) 0.12" (3mm) dimensions aqua drum so in-grade housing kit.
Page 26
24 www.Acclaimlighting.Com dimensions aqua drum ho Ø6.22" (158mm) Ø7.59" (193mm) 2.72" (69.3mm) 8.12" (206.5mm) 3 x 0.43” (3 x 11mm) Ø Ø 1.89" (48mm) 1.97" (50mm) 7.36" (187mm) 8.3" (211mm) 1.97" (50mm) fixture weight: 8 lbs (3.6 kg).
Page 27
25 www.Acclaimlighting.Com Ø8.7" (221mm) Ø6.22" (158mm) Ø8.77" (223mm) 5.71" (145mm) 7.8" (198mm) 0.51" (13mm) 0.12" (3mm) 0.67" (17mm) 8.43" (214mm) 0.55" (14mm) dimensions aqua drum ho in-grade housing kit.
Page 28
26 www.Acclaimlighting.Com limited product warranty a. Acclaim lighting™ hereby warrants, to the original purchaser, acclaim lighting finished products to be free of manufacturing defects in material and workmanship for a standard period of: • fixtures: 5 years (1,825 days) from the date of purchase...
Page 29
27 www.Acclaimlighting.Com.
Page 30: Www.Acclaimlighting.Com
Www.Acclaimlighting.Com.