1. DL manuals
  2. Accton Technology
  3. Switch
  4. 12se
  5. Installation Manual

Accton Technology 12se Installation Manual

Manual is about: Accton Fast Ethernet Hub Installation Manual

Summary of 12se

  • Page 1

    7rde6eyvc9fs)dv 7rde6eyvc9fs"#dv :_der]]rez`_>r_fr].

  • Page 2

    Installation manual 7rde6eyvc9fs)dv 7rde6eyvc9fs"#dv stackable fast ethernet hub with 8/12 10base-t/100base-tx ports.

  • Page 3

    Fast etherhub installation manual 1 introduction general description the eh3008c and eh3012c 100base-tx 8/12 port stackable hubs are entry level 100mbps fast ethernet hubs. They are built around a standard 19-inch chassis which allows stand-alone or rack-mounted operation. These 100base-tx 8/12 port...

  • Page 4

    Fast etherhub installation manual 2 key features ❑ compliant with the ieee802.3u 100mbps repeater specification ❑ 8/12 100base-tx ports for fast ethernet connectivity ❑ 19-inch rack mountable ❑ supports category 5 unshielded twisted-pair cabling (utp) ❑ stackable architecture supports up to 4 hubs w...

  • Page 5

    Fast etherhub installation manual 3 package contents check your package contents for the following parts: æ 8/12 port 100base-tx fast ethernet stackable hub (fast etherhub-8se or fast etherhub-12se) æ power cord æ stackable cable (d-sub 25 pins) æ rack-mount kit æ user ’ s manual if any of these pie...

  • Page 6

    Fast etherhub installation manual 4 hardware description the front panel the front panel contains the 8/12 shielded twisted-pair (stp) ports, one uplink port, and led indicators. Shielded twisted- pair (stp) ports use any one of the stp ports for connection to a 100base-tx node using category 5 utp ...

  • Page 7

    Fast etherhub installation manual 5 led indicators the front panel led indicators help you monitor the status of each port and connected segments. There are 4 different leds on the front panel; including power (pwr), collision (col), link/activity and error. This table lists the leds and their respe...

  • Page 8

    Fast etherhub installation manual 6 the rear panel the rear panel of the hub contains the power socket , 2 d-sub connectors (25 pins) and air fans. P ower socket the power socket accepts ac power of 100 - 240v at 50 - 60 hz..

  • Page 9

    Fast etherhub installation manual 7 hardware installation quick installation procedure 1. Place the hub on a smooth surface or mount it on a rack. 2. Connect power cord to hub and plug in. 3. Connect workstations to hub using category 5 utp cabling. ? Plug an rj-45 connector into any port on the hub...

  • Page 10

    Fast etherhub installation manual 8 select an appropriate location a good location is at or near the center of all the computers you want to link, close to the trunk segment and the other devices you want to connect, and near a convenient power outlet. ? The cable route should not be near any power ...

  • Page 11

    Fast etherhub installation manual 9 setting up 100base-tx stackable hubs 1. Put the 100base-tx stackable hub on the flat surface. ? Ensure the power is off before stacking the hub. 2. Attach the power cord and turn on power to the hub. 3. Connect one end of the d-sub (25 pins) stack cable to the out...

  • Page 12

    Fast etherhub installation manual 10 configuration standard-alone the configuration of a simple stand-alone hub is illustrated as below. The maximum distance between the hub and the workstation is 100 meters..

  • Page 13

    Fast etherhub installation manual 11 uplink multiple hubs if you want to connect more than 8/12 ports, you can use the uplink port to connect to another hub. In compliance with the ieee802.3u class ii specification, two repeaters can be cascaded using 5 meters of cable in a single collision domain. ...

  • Page 14

    Fast etherhub installation manual 12 stacking multiple hubs the 100base-tx stackable hub comes with stackable backplane port for cascading up to 4 hubs. As your network grows, this stackable feature allows you to add additional units for expansion. Depending on the models used, you will be able to s...

  • Page 15

    Fast etherhub installation manual 13 troubleshooting this chapter contains information to help you solve problems. If these hubs are not functioning properly, make sure they were set up according to instructions in this manual. If the hubs don ’ t connect to the network: ➊check the link/activity led...

  • Page 16

    Fast etherhub installation manual 14 other important tips ➀ make sure no more than 100 meters of cable are used between the hub and the desktop. ➁ verify that the cabling type used is correct. (category 5 utp cable) ➂ make sure the network adapter cards installed in the workstations and cable connec...

  • Page 17

    Fast etherhub installation manual 15 product specifications standard ieee802.3u, 100base-tx class i and ii repeater 100base-tx utp ports 8/12 uplink port hub port # 8/12 cable distance 5 meters for repeater to repeater 100 meters for repeater to station cabling stp/utp category 5 wiring, 100-ohm imp...

  • Page 18

    Fast etherhub installation manual 16 emi warning fcc class a certification this device complies with part 15 of the fcc rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including inte...

  • Page 19

    Fast etherhub installation manual 17 ce mark declaration of conformance this is to certify that this product complies with iso/iec guide 22 and en45014. It conforms to the following specifications: emc: en55022(1988)/cispr-22(1985) class b en60555-2(1987) class a iec 1000-4-2(1995)/iec801-2(1991) 4k...

  • Page 20

    18 warranty accton warrants to the original owner that the product delivered in this package will be free from defects in material and workmanship for the lifetime of the product. For the warranty to apply, you must register your purchase by returning the registration card indicating the date of pur...

  • Page 21

    Eh3008c eh3012c e0797-r01.