1. DL manuals
  2. Accton Technology
  3. Network Router
  4. EC3805
  5. Installation Manual

Accton Technology EC3805 Installation Manual

Manual is about: Smart NAT Router

Summary of EC3805

  • Page 1

    Ec3805 smart nat router installation guide www.Edge-core.Com.

  • Page 2

    2 revision history revision date change description ec3805_001r001 04/28/2009 preliminary ec3805_002r001 05/18/2009 add introduction.

  • Page 3

    3 contents smart router user’ s manual ........................................................................................... Revision history .................................................................................................................. 2 b efore y ou u se ....................

  • Page 4

    4 introduction fiber-to-the-home (ftth) has always been an attractive option for internet asccess. It has all the benefits of optical fiber. It provides a future-proof network, in that you do not have to go through the hassles of upgrading from adsl to xdsl, or digital co-ax to digital wireless. It ...

  • Page 5

    5 features: bridging features supports self-learning bridge specified in ieee 802.1d transparent bridging supports up to 4096 learning mac addresses transparent bridging among 10/100 mb ethernet interface supports igmp snooping supports 802.1q vlan packet supports one 100basefx port routing features...

  • Page 6

    6 chapter 1: overview this chapter provides you the description for the leds and connectors in the front and rear surface of the router. Before you use/install this router, please take a look at this information first. Package contents before you start to install the switch, please verify your packa...

  • Page 7

    7 led indicators the nat smart router is equipped with several leds…….As described in the table below (from left to right): led color status description power green on power on off power off link/act. Yellow on connection off disconnection flashing data transmission rear panel the following figure i...

  • Page 8

    8 chapter 2: system requirement and installation system requirement to access the nat smart router via ethernet, the host computer must meet the following requirements: equipped with an ethernet network interface. Have tcp/ip installed. Allow the client pc to obtain an ip address automatically or se...

  • Page 9

    9 connecting to adsl modem and client pc follow the steps below to connect the related devices. 1. Please attach one end of the ethernet cable with rj-45 connector to the lan port of the adsl modem. 2. Connect the other end of the ethernet cable to the wan port of the smart router. 3. Attach one end...

  • Page 10

    10 4. Connect the other end of the cable to the ethernet port of the host pc. 5. Connect the supplied power adapter to the pwr port of your smart router, and plug the other end to a power outlet..

  • Page 11

    11 setting up ip address of host pc in the case the dhcp server function of the smart router is disabled or you want to configure the ip address of the host pc, please follow the steps below for installation. 1. Open the start menu, point to network and dial-up connections and click it. 2. Right-cli...

  • Page 12

    12 4. The internet protocol (tcp/ip) properties window appears. On the general tab: 1) for the case dhcp server of smart router is enabled, enable obtain an ip address automatically and click ok. 2) for the case dhcp server of smart router is enabled or you want to set the ip address by yourself, en...

  • Page 13

    13 after configuring the ip address of the host pc, you can check if the ip address is correctly configured by the following steps: 1. Open the start menu, point to run and click it..

  • Page 14

    14 2. Type cmd in the text book and click ok. 3. A command window will show and in the window type ipconfig /all and then press enter key. 4. In the command window will show the ip address, subnet mask, default gateway…..Etc. Information. The ip address should be 192.168.1.Xxx, xxx is a value other ...

  • Page 15

    15 then your pc and smart router are connected successfully. 3. If the window shows: then your pc and smart router are not connected correctly, you can check: 1) if the ethernet cable between smart router and pc is correctly connected by checking if the link/ack led is on. 2) if the ip address of th...

  • Page 16: Chapter 3: Quick Setup

    16 chapter 3: quick setup this chapter guides you through the steps to configure the basic features of your smart router, so that you can connect to the internet quickly. Using the web-based manager after properly configuring your host pc, please proceed as follows: 1. Start your web browser and typ...

  • Page 17

    17 an example under windows xp is shown as the left figure. 3. After you login successfully, the system info page will appear. From now on, the smart router acts as a web server sending html pages/forms on your request. You can fill in these pages/forms and apply them to the smart router. 4. To surf...

  • Page 18

    18 then choose the wan connection type, pppoe, static ip, or dynamic ip. If you chose pppoe, you have to fix the username/password with your adsl account. Click ok, and you can surf the internet. If you chose static ip,.

  • Page 19

    19 you have to fix the ip address/subnet mask/gateway ip address with the correct values. Click ok, and you can surf the internet. If you chose dynamic ip, smart router will get an ip from the connected dhcp server, and you can surf the internet. 5. If you can not access to the internet, you can che...

  • Page 20

    20 check the account, and configure by following the steps described above. Note: make sure the validity of the account..

  • Page 21: Chapter 4: Advance Setup

    21 chapter 4: advance setup this chapter guides you advanced features configuration of your smart router. 1. Status this page shows the status of your smart router. You can see wan status, lan status and system information here. 2. Lan (1) fix the ip address/subnet mask. (2) if you want to enable dn...

  • Page 22

    22 this page shows the dhcp clients. If the client uses static ip, the type should be static, and if the client uses obtain an ip address automatically, the type should be dynamic. The list is timed refresh. If the entry is aging out, it will be cleared automatically. 4. Wan connection the wan conne...

  • Page 23

    23 you can set wan mac address the same as your pc’s mac address. 6. Bridge convert mark bridge mode enable to convert your smart router as a pure switch. Note: in this case, router functions are invalid. 7. Nat.

  • Page 24

    24 fix server ip with the device’s ip you want to support remote access. Internal port should be the same with you opened on your device. External port should be the port you access remotely. Port type determinates which type of packet should be dealt with. Check enable to make the entry valid. 8. F...

  • Page 25

    25 this page is used to filter lan client mac address. Fix the mac with the mac address you want to filter, mark the deny of the entry, then click apply. 9. Vlan you can set vlan tag id from 1 to 4095 for each port. The max vlan group number is 16. Set vlan id to 0 means disable the vlan group. Afte...

  • Page 26

    26 this page is used to set qos mode and qos rule. Select the mode and rule you want to set, then click apply. You can configure priority per port on this page, from low level to highest level..

  • Page 27

    27 you can configure priority per dscp value (0 to 64) on this page, from low level to highest level. You can configure priority per vlan tag on this page, from low level to highest level..

  • Page 28

    28 you can set ingress rate and egress queue rate on this page. 11. Igmp you can choose igmp disable/snooping/proxy on this page. You also can enable fast leave function..

  • Page 29

    29 igmp status will display on this page. 12. Snmp to enable snmp, select enable option of snmp mode. Fix other blanks with the corresponding value you want to set, then click apply. Note: the community and port should be consistent with snmp client..

  • Page 30

    30 on this page, you can set trap target address and trap target port. 13. Sntp on this page, you can set 5 sntp server here. Your smart router will update the network time automatically when internet connection is ok. You can check the network time on the status page. 14. Port configuration.

  • Page 31

    31 you can set speed and flow control for each port on this page. Then the status should display on port status page. This page shows the link status and speed information of this router. 15. System logs.

  • Page 32

    32 this page shows system logs, such as reboot, clean, factory default setting logs..

  • Page 33

    33 chapter 5: system administration this chapter guides you to managing, upgrading and trouble shooting your smart router. 16. Tool change your account on this page. Upgrade new firmware on this page. Click upgrade and select the firmware to upgrade..

  • Page 34

    34 click ok to restart your smart router. Click apply to restore factory default settings. Note: you also can restore factory default settings by hardware button. Press the button for 5 seconds and release it. The system will restore factory default settings..