Summary of Dyna Drum HO
Page 1
Dyna drum ho™ dyna drum ho qw™ user guide.
Page 3: Contents
1 contents introduction .....................................................................2 welcome 2 safety 2 supplied items 3 optional extras 3 installation ........................................................................4 mounting the unit 4 fitting optional snoots 5 fitting optional s...
Page 4: Introduction
2 introduction welcome welcome to the dyna drum ho range from acclaim lighting. These ruggedized led- powered fixtures are designed to replace traditional external flood lights while using a fraction of the power. Featuring a die-cast aluminum body throughout with full ip66 environmental rating, the...
Page 5
3 supplied items optional extras dyna drum ho or dyna drum ho qw both variants supplied with integral mounting yoke and 5 foot (1.5m) power/control tails. Full snoot (plus four m4 screws) gray [ddhofsg] black [ddhofsb] white [ddhofsw] half snoot (plus four m4 screws) gray [ddhohsg] black [ddhohsb] w...
Page 6: Installation
4 installation mounting the unit each dyna drum ho fixture includes a sturdy yoke mount with multiple holes in its base for various fixing options. Dyna drum ho fixtures weigh 30lbs (13.6kg) - ensure that the mounting surface and the fixings used are sufficiently rated for the task (including wind s...
Page 7
5 fitting optional snoots snoots help to reduce or eliminate light spill into unwanted areas. The full and half snoots available from acclaim lighting are attached to the dyna drum ho units in the same way: trim ring silicone ring lens full or half snoot fitting optional spread lenses the dyna drum ...
Page 8
6 power and control wiring the power and control cords (roughly five feet, 1.5m in length) enter the casing via water- tight glands at the rear of the fixture. As standard the cords are supplied as bare tails. Power the power requirements are as follows: • voltage: 100-277vac 50/60hz • power: 228w a...
Page 9
7 control the control cord has five cores to provide dmx512-a input and output connections: when connecting multiple fixtures, connect the dmx control input lines to the first fixture and feed the output of that fixture to the next. The final fixture in the line should have a 120Ω terminating resist...
Page 10: Operation
8 operation operation of the fixture will commence as soon as power is applied and the user display on the rear panel will first show accl (acclaim) and then either show addr or a dmx address number (if a valid dmx input is present). The fixture may or may not immediately show output from its emitte...
Page 11
9 main menu items (dyna drum ho color changing models) allows you to set the dmx start address for this fixture. This fixture uses four dmx channels (for red, green, blue and white), beginning with the one chosen here. See page 13. Displays the current firmware version for the fixture. No changes ar...
Page 12
10 allows you to set the dmx start address for this fixture. This fixture uses one dmx channel as chosen here. See page 13. Displays the current firmware version for the fixture. No changes are possible within this entry. Displays the ‘fixture hours’ or total operating time (in hours) since the fixt...
Page 13
11 determining solo behavior you can choose how the fixture should behave when it is running solo, either because an external control input is not being used at all or because a connection has been temporarily lost. There are three solo behavior choices: • go dark (blind) - in this mode, when no ext...
Page 14
12 selecting and displaying a static color note: static colors are only possible on dyna drum ho color models. You can choose from a preset palette of static colors or mix your own. In order to view the static color, you will need to ensure the following: • the solo behavior mode is set to the intl ...
Page 15
13 setting the dmx address when external control is used, the dmx start address of the fixture needs to match the start address being used by the controlling device. Color fixtures use four dmx channels (for red, green, blue and white), beginning with the one chosen here; white-only models use just ...
Page 16
14 adjusting the user display you can make adjustments to the user display to suit your installation: • you can invert the display so that it reads correctly when the fixture is mounted inverted. • you can blackout the display when it is not in use - it will re-illuminate when you press a button. To...
Page 17: Further Information
15 further information troubleshooting no light output is visible when expected. • check that power is correctly applied to the fixture and that there is no damage to the power input cord. • use the menu to perform an emitter test. • use the menu to check the internal temperature of the fixture. • i...
Page 18
16 dyna drum ho specifications beam angle 6 degrees (dyna drum ho) 10 degrees (dyna drum ho qw) total lumens 10,103 @ 5500k 6 o (dyna drum ho) 5736 10 o (dyna drum ho qw) lumen maintenance (l 70 ) 50,000 hours housing die cast aluminum ingress protection ip66 power input 100 - 277vac, 50/60hz power ...
Page 19
17 limited warranty a. Acclaim lighting™ hereby warrants, to the original purchaser, acclaim lighting™ finished products to be free of manufacturing defects in material and workmanship for a standard period of 5 years (1,825 days) from the date of purchase. This warranty shall be valid only if the p...
Page 20: Www.Acclaimlighting.Com
Www.Acclaimlighting.Com.