©2008 johnson level & tool 1 self-leveling cross line laser level with 3 vertical lines model no. 40-6602 instruction manual congratulations on your choice of this self-leveling cross line laser level with 3 vertical lines. We suggest you read this instruction manual thoroughly before using the inst...
2 ©2008 johnson level & tool table of contents 1. Kit contents 2. Features and functions 3. Safety instructions 4. Location/content of warning labels 5. Location of parts/components 6. Operating instructions 7. Using the product 8. Self-check and calibration 9. Technical specifications 10. Applicati...
3. Safety instructions please read and understand all of the following instructions, prior to using this tool. Failure to do so, may result in bodily injury. ©2008 johnson level & tool 3 danger! Class iiia laser product max. Power output: ≤ 5mw wavelength: 625-645nm this tool emits laser radiation. ...
4 ©2008 johnson level & tool 4. Location/content of warning labels 1676h-english 10/3/08 10:46 am page 4.
©2008 johnson level & tool 5 5. Location of part/components laser emitting window keypad battery door screw battery door 6v plug (adapter not included) laser emitting window screw hole bench mark locator insert 5/8” thread graduated circle 1676h-english 10/3/08 10:46 am page 5.
6 ©2008 johnson level & tool 6. Operating instructions important: it is the responsibility of the user to verify the calibration of the instrument before each use. Battery installation note: always check to be sure that the on/off switch is in the off position before removing and replacing batteries...
©2008 johnson level & tool 7 wall mount/tripod adapter 1. Put the instrument into the wall mount. The unit can rotate 360º. 2. The wall mount can be mounted on a wall. 3. The benchmark locator insert can be used to find a point on the ground. 4. The wall mount can be attached to a tripod. Rotating 3...
8 ©2008 johnson level & tool 7. Using the product power led: light on: power on light off: power off light flashing: low battery pulse mode led: light on: pulse mode on and the laser can be used with the 40-6780 detector (not included) light off: pulse mode is off manual mode led: light on: manual m...
©2008 johnson level & tool 9 compensator transportation lock hold the upper housing of the instrument, and turn the base in the direction of the arrow. When the instrument is in the “unlock” position, the power led will light. When the instrument is in the “lock” position, the power led will be off....
10 ©2008 johnson level & tool mode led will flash. The instrument is now in the manual mode. Note: when manual mode is on, the laser does not self-level and no out-of-level alarm is indicated. Press the manual mode button again and the instrument will power off. 1. If the instrument is in manual mod...
©2008 johnson level & tool 11 8. Self-check and calibration important: it is the responsibility of the user to verify the calibration of the instrument before each use. Horizontal line for level 1. Set the wall mount/tripod adapter on a tripod or flat surface approxi- mately 10 ft. Away from a refer...
12 ©2008 johnson level & tool 3 vertical lines for plumb 1. Use a plumb line or known vertical reference point. 2. Turn the laser unit on following the instructions above. 3. Rotate the laser unit so the vertical laser line intersects the plumb line. 4. Check all three vertical lines. 5. If the vert...
©2008 johnson level & tool 13 self-calibrating the horizontal laser line and front vertical laser line 1. Locate calibration port on the side of the laser unit. 2. Remove the rubber plug. 3. Unlock the compensator. 4. Use a 2mm hex head wrench. 5. Rotate the screw counter clockwise to lower the left...
14 ©2008 johnson level & tool 10. Application demonstrations 1676h-english 10/3/08 10:46 am page 14.
©2008 johnson level & tool 15 11. Care and handling care must be taken to maintain the accuracy of the instrument. • after each use, the instrument should be wiped clean and kept in its carrying case. • remove dust from the lenses with a soft brush or a nonabrasive wipe. Never touch the lenses with ...
16 ©2008 johnson level & tool it is the responsibility of the user to verify the calibration of the instrument before each use. For further assistance, or if you experience problems with this product that are not addressed in this instruction manual, please contact our customer service department. I...
©2008 johnson level & tool 17 14. Accessories acculine pro ® accessories are available for purchase through authorized acculine pro dealers. Use of non-acculine pro accessories will void any applicable limited warranty and there will be no warranty. If you need any assistance in locating any accesso...
18 ©2008 johnson level & tool 1676h-english 10/3/08 10:46 am page 18.
