Accurate Technology Digi Scale Model 10 User Manual
Summary of Digi Scale Model 10
Page 1
User manual for: and all products with a digi (white) digital readout firmware version p1.040 & higher digi scale ™ digi scale model 10 & model 20
Page 2: Warranty
Accurate technology digi scale page 2 of 17 warranty accurate technology, inc., warrants this product against defective parts and workmanship for 1 year commencing from the date of original purchase. Upon notification of a defect, accurate technology, inc., shall have the option to repair or replace...
Page 3
Accurate technology digi scale page 3 of 17 table of contents section 1 general information........................................................................................... 4 what this manual includes.............................................................................................
Page 4: Ection
Accurate technology digi scale page 4 of 17 s ection 1 g eneral i nformation what this manual includes this manual includes information for: digi scale model 10 part number: 903-2006-001 digi scale model 20 part number: 903-2060-001 about digi scale digi scales are a family of low cost measuring sys...
Page 5: Ection
Accurate technology digi scale page 5 of 17 s ection 2 d igi s cale -10 digi scale is easy to install. By following the installation basics in this manual, you are assured of reliable, error-free operation without any need for adjustments or modifications. Because digi scale can be installed on, or ...
Page 6
Accurate technology digi scale page 6 of 17 1. Determine appropriate mounting locations. Place the encoder in a location that will allow the scale to be inserted into the encoder and attached to the moving part of the target device. 2. Fasten the encoder using three screws (or bolts) to the target d...
Page 7
Accurate technology digi scale page 7 of 17 4. Check that the scale axis is aligned with the direction of motion of the moving part. 5. Attach the scale to the moving part of the target device. Be sure both connections are secure or inaccurate scale readings can occur. 6. Take care when sliding the ...
Page 8
Accurate technology digi scale page 8 of 17 shortening scales to shorten digi scale follow these steps: the scale has stainless-steel wires pressed into the side that could be damaged if not cut properly. 1. Clamp the wires so they do not pull away from the extrusion. 2. Using a hacksaw, cut through...
Page 9: Ection
Accurate technology digi scale page 9 of 17 s ection 3 d igi s cale -20 digi scale is easy to install. By following the installation basics in this manual, you are assured of reliable, error-free operation without any need for adjustments or modifications. Because digi scale can be installed on, or ...
Page 10
Accurate technology digi scale page 10 of 17 3. Referring to the figure, note these two installation requirements: a. For accurate measurements, the guide clip should be mounted perpendicular to the direction of travel of the encoder. B. Over the full range of travel, the guide clip should exert som...
Page 11: Ection
Accurate technology digi scale page 11 of 17 s ection 4 r eadout o peration readout keys timing the keys pictured above have multiple functions. Timing, that is how long a key is depressed, and the combination of the keys pressed is important. This manual uses the term ‘” momentarily ” to describe a...
Page 12
Accurate technology digi scale page 12 of 17 +, 0, and – keys the + (plus), 0 (zero) and – (minus) keys are used to change the currently displayed position to a different value. The 0 key forces the unit to display 0. Momentarily depressing the + key increments the current position by one unit of me...
Page 13: Caution:
Accurate technology digi scale page 13 of 17 reverse scaling if you set a zero point on proscale, moving the scale in one direction will produce positive readings. Moving the scale past zero in the opposite direction will produce negative readings. Reverse scaling means changing the orientation of t...
Page 14
Accurate technology digi scale page 14 of 17 jumpers user configurable jumpers consist of three pins and a ‘shorting block’. The center of these pins is ‘common’. One end pin is labeled ‘a’ and the other end pin is labeled ‘b’. Jp1 reverse scaling changes the direction of readings. Jp2 resolution po...
Page 15
Accurate technology digi scale page 15 of 17 frequently asked questions what f/w (firmware) version do i have? The display will show p1.Xxx on power up. This is the firmware version that your readout uses. What does “err2” mean? If the encoder is off the scale, or the encoder cable is unplugged from...
Page 16
Accurate technology digi scale page 16 of 17.
Page 17: Accurate Technology, Inc.
Accurate technology digi scale page 17 of 17 thank you for choosing an accurate technology product please register your system at http://www.Proscale.Com/registration.Htm accurate technology, inc. 270 rutledge rd. Unit e fletcher, nc 28732 usa 800 233-0580 • 828-654-7920 fax 828-654-8824 www.Digi-ki...