Accurian 42-6051 User Manual
use any of the following to power your CD player
• Two AA alkaline batteries (not supplied).
• Two rechargeable batteries (not supplied). SEE NOTE BELOW.
• Standard AC power using a regulated AC adapter (not
supplied).
• Vehicle battery power using the supplied DC adapter
(not supplied).
alkaline batteries
1. Open the hinged battery cover.
Close when fi nished.
2 Insert two AA alkaline batteries on
top of the ribbon.
rechargeable batteries
1. Insert two rechargeable NiCd
batteries (not supplied). SEE NOTE
BELOW.
2. Plug in the AC/DC adapter.
Charge for 12—15 hours.
3. Unplug the AC/DC adapter. Your
CD player is ready to play.
AC adapter
You can power your CD player using
a 4.5V, 450 mA AC adapter (not supplied). Follow these steps to
connect the CD player to AC power.
1. Insert one end of the AC adapter into the DC IN jack.
2. Plug the other end into an AC wall outlet.
Your CD player will not recharge regular NiCd batteries
(See Ilustration). Consult with your regular RadioShack
store as to the specifi c type of NiCd battery you will need
for your CD player.
Do not touch the AC adapter with wet hands. This can
result in electrical shock.
If the AC adapter is connected when the batteries are
installed, the power supply automatically switches to the
AC power source and the batteries are disconnected.
Please read this user’s guide before
installing, setting up and using your new product
www.radioshack.com
Thank you for purchasing your CD/MP3/FM
Stereo Player from RadioShack.
42-6051
Accurian CD Player with MP3
Playback, and FM Radio
CD player
Users Guide
Headphones
Note: Actual product may vary from the images found in this
document.
Press EQ repeatedly to select different types of music effects (Normal, Classic,
Rock, Jazz, Pop).
NORMAL will automatically be activated when playing CDs or MP3s.
EQ function cannot be activated in RADIO mode.
Press Stop tostop play in all modes.
Press Skip+
to skip forward to the
next track in CD and MP3 mode.
Press and hold the SKIP+
or SKIP-
during play to scan the disc at high
speed. When you fi nd the desired
section of the disc, release the button.
Normal play will resume.
PLAY/PAUSE to activate CD/ MP3 mode. Press and hold PLAY/PAUSE. As
the disc begins to spin, READING appears on the display.
When the music
begins
adjust the volume as desired. Press PLAY/PAUSE again to pause.
The elapsed time will fl ash on the display.Resume normal play by pressing
PLAY/PAUSE.
Press Preset - to preset radio
station down in Tuner mode.
Press SKIP -
once to skip to
the beginning of the current
track, or repeatedly to skip to
previous tracks.
Press Mode/FM ST./Mono to select
play modes Repeat 1, Repeat All,
Repeat Directory, Intro, or Random in
CD and MP3 mode.
Intro scan play - For CDs and MP3s,
repeatedly press MODE until INT
appears. Press PLAY/PAUSE to
activate. The fi rst 10 seconds of each
track will play in order.
Random play - Press Mode until RAN
appearsto play CD or MP3 tracks in
random order. Press PLAY/PAUSE to
activate. When all tracks on the disc
have been played, the player will shut
off automatically.
Use PROG./MEM. to program your
favorite tracks in CD mode, or your
favorite radio stations in Tuner mode.
ESP activates the antishock protection
system for 45 seconds in CD mode, and
120 seconds in MP3 mode.
NOTE
programmed play
CD and MP3 tracks on a disc can be
programmed to play in any order. Up to 60
tracks can be programmed.
1. In
stop
mode,
press
PROG./MEM. The
track number 00 fl ashes. PGM and
program number P01 are shown or 00
000 fl ashes. In MP3 mode PGM and
program number PO1 are shown.Press
SKIP+
or SKIP- to select the fi rst track to be programmed.
When programing in MP3 mode, press the DIR/PRESET+ or
DIR/PRESET - to select directory.
2 Press
PROG./MEM. again to store the track you selected. The
display P01 changes to P02.
3. Repeat steps 1 and 2 to program additional tracks.
4. After
you
fi nish programming, press PLAY/PAUSE.
Programmed play begins from the fi rst programmed track.
The
player stops automatically after all programmed tracks have been
played. The programmed tracks are stored in memory until the
disc compartment is opened or power is turned off.
hold switch–hold all buttons
Once you have made all adjustments
and selections, slide HOLD to ON. HOLD
appears on the display. This locks all
buttons. Slide the HOLD SWITCH to OFF to
unlock all controls.
r
epeat play
For CDs and MP3s to repeat a single track, press MODE once during
play. REPT1 appears in the display. Press SKIP+
or SKIP- to
select your favorite song. The song will repeat until you press STOP.
To repeat all tracks on a CD, press MODE twice during play. REPT ALL
will show in the display. All songs will repeat over again until you press
the STOP button.
For MP3 discs, ESP
cannot be cancelled
after you
activate it.
Because your MP3
disc has a large
capacity, the
disc-reading time
will increase.
fi le-selection
playback
Press DIR/PRESET,
SKIP+
or SKIP-
to select the fi les you
want to include in the same playlist, just as you would
with a CD.
To select different fi les from different directories, in play
mode, select the directory fi rst, then choose the fi le you need
in the directory.
1. Connect the supplied headphones into
the PHONES jack.
2. Slide
the
OPEN switch to open the CD
door. Insert a disc label side up. Close
the CD door.
open
headphones
volume
hold
hold
line out
DC in
Hold switch
USB - enhances
bass effect
NOTE
NOTE
The power turns on automatically when
you press PLAY/PAUSE or Radio.
The power turns off automatically after
about 30 seconds when you press STOP,
or all the tracks on a disc have been
played.The power turns of immediately
when you press Stop twice.
place disc here