1. DL manuals
  2. Accusplit
  3. Watch
  4. AX602M500
  5. Operating Instructions Manual

Accusplit AX602M500 Operating Instructions Manual

Manual is about: DIGITAL QUARTZ STOPWATCHES

Summary of AX602M500

  • Page 1

    B-1 accusplit, inc. 6120 stoneridge mall rd., suite 210 pleasanton, ca 94588 usa 800-965-2008 • 925-226-0888 • fax 925-463-0147 www.Accusplit.Com • support@accusplit.Com 980-314 accusplit® e x c l u s i v e ax602m500 ax602m500dec digital quartz stopwatches operating instructions 2-3 2 3 important no...

  • Page 2

    4-5 4 5 general features • accusplit x case with ergonomic design and no-fail buttons • 4 button operation • large lcd display with contrast adjustment • 12/24 hour display • time of day and chime • daily alarm • full 1/100 second chronograph with working range from 0 to 19 hr. 59 min. 59.99 seconds...

  • Page 3

    8-9 8 9 this is only a brief description of these buttons. Detailed uses of the buttons are different in particular functions and will be described later in the instructions. Pressing [mode] button will toggle among the modes above. Note that there is no auto-return function in the stopwatch. Whenev...

  • Page 4

    12-13 12 13 date-month (d-m), sound on or off, contrast (darkness of the digits - default is 9), then back to second, and recycles again. Note: when the second is to be set, press [start • split] to reset the second digits to zero. At the end of setting, press [recall] (s4) or [mode] to exit from th...

  • Page 5

    16-17 16 17 chronograph and recall mode press [mode] until you enter the chrono mode. The stopwatch can measure up to 19 hours, 59 minutes, 59.99 seconds. When you enter the chronograph mode, the display format is as below. The upper line shows the split time, the middle line shows the lap time and ...

  • Page 6

    20-21 20 21 when there are 5 free memories left, the icon “full” will blink to remind you of the nearly full situation. Whenever the storage is full, extra split/lap times will not be stored into memory but will still be shown on the display. Any fastest and slowest laps will not be stored. The memo...

  • Page 7

    24-25 24 25 please note that if the stopwatch is running, no selection for chronograph operating modes can be made until the stopwatch has been stopped and reset. Segmented run memory for lap/split time storage. A header consisting of the date/time stamp is attached to each segment to indicate the m...

  • Page 8

    28-29 28 29 [recall] [recall] [recall] [recall] [recall] after recalling the fi rst record, press [recall] once more to exit from recall mode and go back to chronograph mode. The “recall” icon will turn off. Note: watch is still running so run time continues to advance. 30-31 30 31 data mode press [...

  • Page 9

    32-33 32 33 the header consisting of the date/time stamp will be shown. The number of laps in the segment will appear in the upper left while the segment num- ber is displayed in the middle left. If the segment shown is not your desired segment, press [start • split] to reach the desired segment. Th...

  • Page 10

    36-37 36 37 note: you cannot delete all segments while the stopwatch is running. If nothing happens when you push and hold [stop • reset] check to make sure the stopwatch is stopped. Timer mode press [mode] until you enter the timer mode. 3 count-down operation modes are available on this stopwatch:...

  • Page 11

    40-41 40 41 how to set the timer press and hold [recall] (s1) for 2 seconds to activate timer setting. Timer setting starts with second digits, which are shown blinking. You can press [start • split] (s3) to advance the fl ashing digits. Or you can press [stop • reset] (s2) to select other digits. T...

  • Page 12

    44-45 44 45 stroke/stride measurement press [mode] until you enter the stroke measure- ment mode. The display will be as follows. In the stroke or strides measurement mode, the duration of 3 strokes is taken and the stroke frequency (counts per minute) is calculated. If the stroke frequency falls ou...

  • Page 13

    48-49 48 49 press [start • split] (s3) to toggle between km and mile. To select the following digits, press [stop • reset] (s2). The far right digit will blink and you can set the distance from the least signifi cant digit to the most signifi cant digit. The distance can be set in the range 0.000 to...

  • Page 14

    52-53 52 53 both the speed and elapsed time can be retrieved. Lap time & speed recall similar to the chrono recall mode, during speed measurement or stop state, you can press [recall] to recall the speed/lap memories. The mode message will be shown for one to two seconds as the mode message display ...