Altos g310 service guide part no.: vd.G31vf.001 printed in taiwan service guide files and updates are available on the csd web; for more information, please refer to http://csd.Acer.Com.Tw.
Ii revision history please refer to the table below for the updates made on altos g310 service guide. Date chapter updates 2004/06/18 ch2 update the bios screen -- product information on page 27..
Iii copyright copyright © 2004 by acer incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optica...
Iv conventions the following conventions are used in this manual: screen messages denotes actual messages that appear on screen. Note gives bits and pieces of additional information related to the current topic. Warning alerts you to any damage that might result from doing or not doing specific acti...
V preface before using this information and the product it supports, please read the following general information. 1. This service guide provides you with all technical information relating to the basic configuration decided for acer's "global" product offering. To better fit local market requireme...
Vii table of contents chapter 1 system introduction 1 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 front bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 fro...
Viii table of contents reassemble the cpu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 reassemble the system fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 reassemble the dimm . . . . . . . . . . . . . . . . . . . . . . . ...
Chapter 1 1 features system ! Processor ! Support for an intel pentium 4 processor with hyper-threading technology in a mpga478 socket ! Supporting 533mhz fsb 2.8ghz pentium 4(northwood) processor, or 800mhz fsb 3.0 to 3.4 ghz pentium 4 (prescott) processors. ! Chipset ! North bridge: intel 82875p m...
2 altos g310 ! Media storage ! One 3.5 inch, 1.44 mb floppy drive ! One 5.25 inch high speed cd-rom drive ! Additional media storage capacity ! Support for two 3.5 inch s-ata, ata, or scsi hard disk drives ! Four additional 5.25 inch half-height bays (one has been occupied by cd-rom) ! Bios ! 512kb ...
Chapter 1 3 ! Lan connector ! One rj-45 jacks for lan connectors ! One parallel port connectivity ! Serial port ! Two high speed ns pc87373 compatible uart with send/receive 16 byte fifo serial port ! Usb port ! Six usb ports support universal hci specification for usb 2.0 (2 front, 4 rear).
4 altos g310 front bezel no. Item 1 cd-rom drive 2 cd-rom headphone port 3 cd-rom volume control 4 cd-rom activity indicator 5 fdd eject button 6 fdd (floppy disc drive) 7 fdd activity indicator 8 security keylock 9 system power indicator 10 system power button 11 usb 2.0 ports (two) 12 5.25-inch ha...
Chapter 1 5 front panel no. Item 1 cd-rom 2 cd-rom headphone port 3 cd-rom volume control 4 cd-rom activity indicator 5 fdd eject button 6 fdd (floppy disc drive) 7 fdd activity indicator 8 security keylock 9 system power indicator 10 system power button 11 usb 2.0 ports (two) 12 5.25-inch half-heig...
6 altos g310 rear panel no. Item 1 main power supply unit 2 ps/2 mouse port 3 ps/2 keyboard port 4 parallel/printer port 5 serial ports (two) 6 usb 2.0 ports (four) 7 gigabit lan port (10/100/1000 mbps) 8 agp add-on card (actual ports vary by configuration) 9 side panel tool-less screws (top and bot...
Chapter 1 7 internal components no. Item 1 power supply unit 2 system fan 3 mainboard 4 pci bus slot 5 hdd bays 6 3.5” device bay 7 5.25” device bay.
8 altos g310 system block diagram r.
Chapter 1 9 system board layout the mainboard becomes accessible once you open the system. It should look like the figure shown below. Label component label component agp1 agp slot bat1 battery cpu fan cpu fan connector dimm 1,2,3,4 dimm slot fdd1 floppy disck drive connector j10 front panel header ...
10 altos g310 u23 bios u25 mini-bmc usb1 front usb connector usb2 dual usb connector label component label component.
Chapter 1 11 hardware specifications and configurations system board major chips item controller system core logic nb (canterwood): intel 875p sb (canterwood): ich5r super i/o controller ns pc87373 lan controller intel 82547gi memory controller build in intel 875p agp controller build in intel 875p ...
12 altos g310 bios hotkey list hotkey function description m enter bios setup utility press while the system is booting to enter bios setup utility. Cache memory item specification first-level cache configurations cache function control enable/disable by bios setup second-level cache configurations ...
Chapter 1 13 memory combinations dimm1 dimm2 dimm3 dimm4 memory interleave dynamic mode throughput level 256mb 1-way yes 2 512mb 1gb 256mb 256mb 2-way yes 4 512mb 512mb 1g 1g 256mb 256mb 256mb 256mb 2-way yes 4 512mb 512mb 512mb 512mb 1gb 1gb 1gb 1gb memory throughput level throughput level memory c...
14 altos g310 diskette drive interface item specification diskette drive controller built-in ns pc87373 super i/o controller diskette drive controller resident bus lpc bus supported diskette drive formats 1.44mb, 2.88mb format and slim type diskette drive function control enable/disable by bios setu...
Chapter 1 15 i/o address map hex range device function 000-01f dma controller-1, 8237 020-027 interrupt controller-1 8259 030-037 interrupt controller-1 8259 040-047 system timer (8254-1) 050-057 system timer (8254-1) 060-06f keyboard controller 8742 070-07f real-time clock, nmi mask 080-09f dma pag...
16 altos g310 pci interrupt routing pci devices req#/gnt# idsel others pci slot 1 p_req#1 p_gnt#1 d_ad17 from sb / pci slot pci slot 2 p_req#2 p_gnt#2 d_ad18 from sb / pci slot pci slot 3 p_req#3 p_gnt#3 d_ad19 from sb / pci slot pci slot 4 p_req#4 p_gnt#4 d_ad20 from sb / pci slot pci slot 5 p_req#...
Chapter 1 17 power management power saving mode phenomenon list power saving mode phenomenon device standby mode ! Independent power management timer for hdd devices (0-15 minutes, time step = 1 minute) ! Hard disk drive goes into standby mode (for ata standard interface) ! Disable v-sync to control...
18 altos g310 environmental requirements item specifications temperature operating +10 to +35°c non-operating -10 to +60°c non-operating (storage package) -20 to +60°c humidity operating 20% - 80% rh, non-condensing non-operating (unpacked) 20% - 80% rh, non-condensing non-operating (storage package...
Chapter 1 19 mechanical specifications item specification dimensions w/o bezel 186(w) x 424(h) x 460(d)mm w/bezel 186(w) x 424(h) x 477(d)mm color black i/o ports ps/2 keyboard port, ps/2 mouse port, two usb ports, one lan ports, two serial port slots 5 pci slots , 1agp slot main board fs-1100a driv...
20 altos g310 asm asm 6.0 asm is a system management tool based on the simple network mangement protocol ( snmp) and remote rrocedure call (rpc) via service provider. It detects server problems related to the processor thermal condition, voltage detection, fan status or redundant power supply status...
Chapter 1 21 intelligent platform mangement interface ( ipmi) ipmi stands for intelligent platform management interface. Ipmi is an open standard hardware manageability interface specification. It provides an architecture that defines how unique device can all communicate with the cpu in a stadard w...
22 altos g310
Chapter 2 22 introduction most systems are already configured by the manufacturer or the dealer. There is no need to run setup when starting the computer unless you get a run setup message. The setup program loads configuration values into the battery-backed nonvolatile memory called cmos ram. This ...
23 chapter 2 setup menu the computer employs the latest ami bios cmos chip with support for windows plug and play. This cmos chip contains the rom setup instructions for configuring the mainaboard’s bios. The bios(basic input and output system) setup utility is a menu driven utility that enables you...
Chapter 2 24 main menu parameter description options bios build date the date when the bios build mm/dd/yy) bios version version control n/a smbios version smbios version of bios x.X.X system time use these items to set the correct time. (hh:mm:ss) system date use these items to set the correct date...
25 chapter 2 system information parameter description option processor type processor type that is currently installed xxxxxxxx processor speed processor speed that is currently installed x.Xghz cpu id cpu id for the cpu xxxxh level 1 cache data cache size xxxkb level 2 cache cache size xxxkb floppy...
Chapter 2 26 total memory mouse (ps/2, usb) display device type if device is present display “none” if device is not present ps/2, none none, usb ps/2, usb none, none keyboard (ps/2, mouse) display device type if device is present display “none” if device is not present ps/2, none none, usb ps/2, us...
27 chapter 2 product information parameter description option system product name display the string that is stored in smbios table “type1 : offset 05h:product name”. It is flashed at factory and would be updated by smbios update utility. Altos xxxx system serial no. Unique id. Display the string th...
Chapter 2 28 advanced menu the advanced menu contains parameter values that define how the system behaves on startup. Warning:be cautious in setting parameter values in the advanced menu as any incorrect value may cause the system to malfunction. Press [enter] to enter the submenu scree of the param...
29 chapter 2 peripheral configuration parameter description option serial port a (address/irq) serial port 1 address and irq (interrupt request) setting disabled 3f8/irq4 2f8/irq3 3e8/irq4 2e8/irq3 serial port b (address/irq) serial port 2 address and irq (interrupt request) setting disabled 2f/8/ir...
Chapter 2 30 ide configuration the ide configuration submenu lets you define the parameter settings related to the hard disk. Parameter decription option ide configuration p-ata mode: default setting. P-ata device is configured in legacy mode. Combined mode: allows configuration of p-ata and s-ata d...
31 chapter 2 primary ide master parameter description option device type of ide device n/a vendor vendor of the selected ide device n/a size size of the selected device n/a type configure the driver type. Not installed auto cd-rom armd lba/large mode select the hard disk drive translatoin method. Fo...
Chapter 2 32 dma mode optimal default failsafe default auto swdman mwdman udman s.M.A.R.T enable or disable the s.M.A.R.T ( self- monitoring, analysis and reporting technology) in the internal hard disk. If auto is selected, the bios will enable the s.M.A.R.T if the driver supported. Auto disabled e...
33 chapter 2 floppy configuration the floppy configuration submenu displays the type of floppy drive installed in the server. Parameter description option floppy drive a floppy disk drive type 1.44/1.25mb none.
Chapter 2 34 pci/pnp configuration the pci/pcp configuration submenu lets you specify the settings for the pci devices. Parameter description option usb function enables the system’s usb ports enabled disabled legacy usb support enable this parameter when you intend to use a usb device and are using...
35 chapter 2 boot settings configuration the boot settings configuration submenu lets you specify the preferred setting for system bootup. Parameter description option quick boot allows bios to skip certain tests while booting. This will decrease the time needed to boot the system. Enabled disabled ...
Chapter 2 36 ps/2 mouse support default is “enabled” disabled ps/2 device if disabled. Enabled disabled wait for “f1” if error default is “enabled”. Display below message when post error occurred. Wait for 5 seconds and continuing to boot up. Press “f1” to continue or f2 to enter bios setup. Display...
37 chapter 2 onboard device configuration the onboard device configuration submenu displays the types of devices the system board can support. Parameter description option onboard lan gigabit ethernet support enabled disabled onboard s-ata serial ata drive support enabled disabled.
Chapter 2 38 event log configuration note: if there are any event logs recorded. “ view event log” and “ mark all events as read” will appear. If no event recorded, these two options will not appear..
39 chapter 2 parameter description options event logging enables or disables the event logging function of the system enabled disabled clear all event logs pop-up a new diaglog box, to confirm if user wants to clear all event logs now. The message in the diaglog box: “clear all event logs now ?” yes...
Chapter 2 40 remote access configuration the remote access configuration submenu lets you specify settings related to the syste’s remote management features. Parameter description option remote access enables or disables remote access. Selecting serial enables remote access and opens a submenu to co...
41 chapter 2 flow control selecting hardware enables flow control of remote access. None hardware parameter description option.
Chapter 2 42 system health monitoring the system health monitoring submenu lets you check various system parameters. This information is for reference only, no parameters in this submenu can be changed. Parameter description option cpu temperature current cpu temperature detected by the sensor on th...
43 chapter 2 power menu the power menu allows you to configure the system’s power management feature. Parameter description options acpi aware o/s yes/no acpi support for operating system. Yes: if os supports acpi. No: if os does not support acpi. Yes no power management enable or disable apm suppor...
Chapter 2 44 boot menu the boot menu allows you to specify the preferred settings during system bootup. Press [enter] to enter the submenu screen of the parameters shown in the screen below. Parameter description option boot device priority specifies the boot sequence from the availablede- vices. Re...
45 chapter 2 boot device priority the boot device priority submenu lets you specify the boot search sequence during the post process. Bios setup wil ldisplay an error message if the drive specified is not bootable. Parameter description 1st boot device sets the device from which the system will firs...
Chapter 2 46 security menu parameter description option supervisor password prevents unauthorized access to the bios setup. Not installed installed user password secures your system against unauthorized use. Once you set this password, you have to type it whenever you boot the system. User password ...
47 chapter 2 exit menu parameter description save changes and exit exit system setup wiht saving the changes discarding changes and exit exit system setup without saving the changes. Load optimal defaults load optimal defaults load failsafe defaults load failsafe defaults discard changes discard cha...
Chapter 3 48 this chapter contains step-by-step procedures on how to disassemble the server system for maintenance and troubleshooting. To disassemble the computer, you need the following tools: ! Wrist grounding strap and conductive mat for preventing electrostatic discharge ! Phillips screw driver...
49 altos g310 general information before you begin before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the power cable from the system..
Chapter 3 50 disassembly flowchart.
51 altos g310 standard disassembly procedure this section tells you how to disassemble the system when you need to perform system service. Please also refer to the disassembly video, if available. Caution: before you proceed, make sure you have turned off the system and all peripherals connected to ...
Chapter 3 52 4. Pulling the cd-rom, floppy and hard disk drive from the chassis. 5. Detach the bracket from the cd-rom. 6. Detach the bracket from the floppy. 7. Detach the bracket from the hard disk drive. Removing the cables 1. Disconnect the power cable from the mainboard 2. Disconnect the 12 vol...
53 altos g310 removing the dimm 1. Press the holding clips on both sides of socket outward to release the dimm and take it away. Removing the system fan 1. Disconnect the system fan cable. 2. Take the system fan from the chassis. Removing the cpu 1. Disconnect the cpu fan cable from the mainboard 2....
Chapter 3 54 4. Lift up the cpu locking lever until it is fully extended and take cpu away from the socket. 5. Then press down the locking lever to the end. Removing the mainboard and extension board 1. Remove the nine screws to release the mainboard. 2. Then gently to take the mainboard from the ch...
55 altos g310 removing the power button and usb modules 1. Remove the two screws to release the lock switch cable. 2. Then take the lock switch cable away. 3. Remove the two screws to release the module. 4. Take the module away from the chassis. 5. Take the usb module away from the chassis. 6. Remov...
Chapter 3 56 8. Remove the one screw to release the power button board from the bracket. 9. Take the power button board from the bracket. 10. Disconnect the intrusion alarm cable. 11. Disconnect the cable from the power button board. 12. Remove the two screws. 13. Take the usb module away from the b...
57 altos g310 standard reassembly procedure this section tells you how to reassemble the system when you need to perform system service. Please also refer to the disassembly video, if available. Caution: before you proceed, make sure you have turned off the system and all peripherals connected to it...
Chapter 3 58 8. Aim at the secure position to place the lock module. 9. Secure the one screw to fasten the lock. 10. Place the usb module to the position. 11. Place this module to this position. 12. Secure the two screws to fasten the module. 13. Place the lock switch cable on the position and secur...
59 altos g310 reassemble the power supply 1. Aim at the track to place the power supply to the chassis. 2. Then secure the four screws. Reassemble the mainboard and extension board 1. Reconnect the extension daughter board to the mainboard. 2. Aim at the i/o shield position to place the mainboard wi...
Chapter 3 60 4. Place the heatsink to the position. 5. Hook the cpu locking lever to fasten it. 6. Reconnect the cpu fan cable to the position. Reassemble the system fan 1. Place the system fan to the chassis. 2. Reconnect the system fan cable to the position. Reassemble the dimm 1. Insert the dimm ...
61 altos g310 reassemble the cables 1. Reconnect the secondary ide cable, primary ide cable and floppy ide cable to the mainboard. 2. Reconnect the 12 voltage power cable to the mainboard. 3. Reconnect the power cable to the mainboard. Reassemble the cd-rom, floppy and hdd 1. Place the bracket to th...
Chapter 3 62 4. According the track to insert hard disk drive to the chassis. 5. Aim at the position to insert the floppy. 6. Aim at the position to insert the cd-rom. 7. Reconnect the ide cable and power cable to the hard disk drive. 8. Reconnect the ide cable and power cable to the floppy. 9. Reco...
63 altos g310
Chapter 4 62 this chapter provides troubleshooting information for the altos g310: ! Bootblock initialization code checkpoints ! Bootblock recovery code checkpoints ! Post code checkpoints ! Beep codes troubleshooting chapter 4.
63 altos g310 bootblock initialization code checkpoints the bookblock initialization code sets up the chipset, memory and other components before system memory is available. The following table describle the type of checkpoints that may occur during the bootblock initialization portion of the bios: ...
Chapter 4 64 bootblock recovery code checkpoints the bootblock recovery code gets control when the bios determines that a bios recovery needs to occur because the user has forced the update or the bios checksum is corrupt. The following table describle the type of checkpoints that may occur during t...
65 altos g310 post code checkpoints the post checkpoints are the largest set of checkpoints during the bios pre-boot process. The following table describes the type of checkpoints that may occur during the post portion of the bios: checkpoint description 03 disable nimi,parity, video for ega, and dm...
Chapter 4 66 37 displaying sign-on message, cpu information, setup key message, and any oem specific information. 38 initializes different devices through dim. 39 initializes dmac-1 & dmac-2 3a initializes rtc date/time 3b test for total memory installed in the system. Also, check for del or esc key...
67 altos g310 beep codes the following table describes the beep codes that are used by amibios: number of beeps description 1 memory refresh timer error 2 parity error 3 main memory read/ write test error 4 mainboard timer not operational 5 processor error 6 keyboard controller bat test error 7 gene...
Chapter 5 68 jumpers and connectors refer to the following figure for the location of the jumpers and connectors on the main board: connector/jumper label description agp1 agp slot bat1 battery cpufan cpu fan connector dimm 1,2,3,4 dimm port fdd1 floppy connector j10 front panel header j11 buzzer co...
69 altos g310 j3 ps/2-kbms j4 serial and parallel print port j5 dual usb & rj45 j6 extend interface j7 power port & 12v power connector j9 main power connector jp8 clear cmos jp9 i 2 c feature connector pci 1,2,3 pci slot ext pci 1, 2 extention pci slots pide 1,2 primary ide connector secondary ide ...
Chapter 5 70 print port serial port pin no. Pin description pin no. Pin description 1 stb# 15 -perror 2 data bus1 16 -pprinit 3 data bus 2 17 -pslctin 4 data bus 3 18 gnd 5 data bus 4 19 gnd 6 data bus 5 20 gnd 7 data bus 6 21 gnd 8 data bus 7 22 gnd 9 data bus 8 23 gnd 10 ack# 24 gnd 11 busy 25 gnd...
71 altos g310 serial ata port ps2-kbms cn21 sata pin no. Pin description pin no. Pin description 1 gnd 6 sata_rxn0 2 sata_txp0 7 gnd 3 sata_txn0 8 nc 4 gnd 9 nc 5 sata_rxn0 j3 pin no. Pin description pin no. Pin description 1 kbdata 10 power 2 nc 11 msclk 3 gnd 12 nc 4 power 13 gnd 5 kbclk 14 gnd 6 ...
Chapter 5 72 dual stack usb port dual usb & rj45 connector usb2 pin no. Pin description pin no. Pin description 1 5v_dual_back 6 usb data bus 2 usb data bus 7 usb data bus 3 usb data bus 8 gnd 4 gnd 9 gnd 5 5v_dual_back 10 gnd pin no. Pin description pin no. Pin description 1 usb pwr 15 gnd 2 usbp2n...
73 altos g310 5 usb pwr 19 3.3v 6 usbp3n_r 20 active_ledj 7 usbp3n_r 21 gnd 8 gnd 22 gnd 9 ltdp_8100 23 gnd 10 ltdn_8100 24 gnd 11 lrdp_8100 25 gnd 12 nc 26 gnd 13 nc 27,28 gnd 14 lrdn_8100 29,30 gnd pin no. Pin description pin no. Pin description.
Chapter 5 74 front panel i/o and led front panel connector j10 pin no. Pin definition 1 power led_a power led anode 2 5vsb 5vsb 3 key key 4 cooling fault led_a cooling fault led anode 5 power led_c power led cathode 6 cooling fault led_c cooling fault led anode 7 hdd activity led_a hdd activity led ...
75 altos g310 led definition led indicator color condition describes power/sleep led green on s0: power on green blink (1hz with at 50% duty cycle) s1: sleep amber on s3 - off s4 - off s5 status led green on system ready/no alarm green blink (1hz with at 50% duty cycle) system ready but degraded (so...
Chapter 5 76 front usb header usb header setting pin no. Signal name pin definition 1 vbus front panel usb power (port 0,1) 2 vbus front panel usb power (port 0,1) 3 d- front panel usb port 0 negative signal 4 d- front panel usb port 1 negative signal 5 d+ front panel usb port 0 positive signal 6 d+...
77 altos g310 gpio definitionconnector and jumper setting ide connector component pin no. Pin define function define ich5 u3 gpi7 front audio det y2 gp18 lan_pem# ac3 gpi11 ipmi_alert# w5 gpi13 io_pme# f22 gpo23 fwh_wp# f21 gpio34 vcc26_en sio 103 gpioe00 gpio_power_led 105 gpioe02 gpio_status_led s...
Chapter 5 78 floppy connector fan connector setting pin no. Pin define pin no. Pin define 1 gnd 18 dip# 2 drvden0 19 gnd 3 nc 20 step# 4 nc 21 gnd 5 gnd 22 wd# 6 nc 23 gnd 7 gnd 24 we# 8 index# 25 gnd 9 gnd 26 trak0# 10 moa# 27 gnd 11 gnd 28 wp# 12 dsb# 29 gnd 13 gnd 30 rdata# 14 dsa# 31 gnd 15 gnd ...
79 altos g310 i2c connector clear cmos note: 1-2: normal note: 2-3: clr cmos sysfan2 setting pin no. Pin define 1 gnd 2 fanpower 12v 3 lm85 tach2 jp9 setting pin no. Pin define 1 gnd 2 ipmi_scl 3 ipmi_sda 4 tris j8 setting pin no. Pin define 1 normal 2 clear 3 gnd sysfan2 hf08030-p1 hf08030-p1 1 1 2...
Chapter 6 80 this chapter gives you the fru (field replaceable unit) listing in global configurations of altos g310. Refer to this chapter whenever ordering for parts to repair or for rma (return merchandise authorization). Important: please note when ordering fru parts, that you should check the mo...
81 altos g310 exploded diagram.
Chapter 6 82 part list picture partname description aecr no. Board daughter board 2usb usb board 55.G31vf.001 power button board power switch board 55.G31vf.002 extension daughter board tbd 55.G31vf.003 cable fdd cable 34pin 2con fdd cable 50.G31vf.001 hdd ide cable 40pin (short) hdd cable 50.G31vf....
83 altos g310 intrusion alarm 7pin 2con intrusion switch 50.G31vf.008 s-ata cable 7pin 2con cable sata 270mm red foxconn 50.G31vf.009 s-ata power cable 2con cable sata power 1-2h 150mm foxconn 50.G31vf.010 case/cover/bracket/assemble right cover left bracket door sub assy 60.G31vf.001 front bezel w/...
Chapter 6 84 retention module w nail 4pcs tbd 42.G31vf.002 i/o bracket holder pci-bkt 42.V02vf.707 chassis w i/o bracket, db bracket, led bracket w/o i/o shield g310 sub case assy (w/o i/ o shield) 60.G31vf.003 fdd holder fdd rail 33.V02vf.704 odd holder cd-rom rail 33.V02vf.705 hdd holder assy (rig...
85 altos g310 power supply 300w w pfc atx12v fsp300-60pln power supply 300w w pfc atx12v fsp300-60pln py.30008.003 picture partname description aecr no..
Appendix a 86 the altos g310 model no. Define: 1. Trade mark: 2. Brand name: acer 3. Description: intel p4 processor with hyper-threading technology a. North bridge : intel 875p b. South bridge : ich5r c. Super i/o controller : ns pc87373 4. Model no: altos g310 5. Product name: acer altos g310 mode...
Appendix b 87 this computer’s compatibility is a test plan released by wistron internal testing department. Once the final report is available, this chapter will be revised accordingly. Test compatible components appendix b.
88 altos g310 win nt4.0+sp6 environment test item specifications cpu p4 3.6ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#:857996 p4 3.4ghz/800fsb/1mb prescott, mpga478, sl7b8, d-1 stepping, mm#: 857995 p4 3.2ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#: 857996 p4 3.0ghz/800...
Appendix b 89 u160 asrc/1s 1ch ultra160 raid card lsi express500, 32/33mhz pci, i960rm-100, 32mb sdram, acer altos cd4.0, graphics card agp 8x graphices card (entry) ag200e4-d32 xabre 200/ 32mb ddr std agp 8x graphices card (middle) leadtek geforce fx5200, lr2967, 64mb, dual 350mhz, opengl 1.4, w/tv...
90 altos g310 win2000 advanced s erver environment test item specifications cpu p4 3.6ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#:857996 p4 3.4ghz/800fsb/1mb prescott, mpga478, sl7b8, d-1 stepping, mm#: 857995 p4 3.2ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#: 857996 p4...
Appendix b 91 asrc/1s 1ch ultra160 raid card lsi express500, 32/33mhz pci, i960rm-100, 32mb sdram, acer altos cd4.0, graphics card agp 8x graphices card (entry) ag200e4-d32 xabre 200/ 32mb ddr std agp 8x graphices card (middle) leadtek geforce fx5200, lr2967, 64mb, dual 350mhz, opengl 1.4, w/tv-out,...
92 altos g310 windows 2003 enterprise edition environment test item specifications cpu p4 3.6ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#:857996 p4 3.4ghz/800fsb/1mb prescott, mpga478, sl7b8, d-1 stepping, mm#: 857995 p4 3.2ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#: 85...
Appendix b 93 asrc/1s 1ch ultra160 raid card lsi express500, 32/33mhz pci, i960rm-100, 32mb sdram, acer altos cd4.0, graphics card agp 8x graphices card (entry) ag200e4-d32 xabre 200/ 32mb ddr std agp 8x graphices card (middle) leadtek geforce fx5200, lr2967, 64mb, dual 350mhz, opengl 1.4, w/tv-out,...
94 altos g310 windows xp environment test item specifications cpu p4 3.6ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#:857996 p4 3.4ghz/800fsb/1mb prescott, mpga478, sl7b8, d-1 stepping, mm#: 857995 p4 3.2ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#: 857996 p4 3.0ghz/800fsb...
Appendix b 95 asrc/1s 1ch ultra160 raid card lsi express500, 32/33mhz pci, i960rm-100, 32mb sdram, acer altos cd4.0, graphics card agp 8x graphices card (entry) ag200e4-d32 xabre 200/ 32mb ddr std agp 8x graphices card (middle) leadtek geforce fx5200, lr2967, 64mb, dual 350mhz, opengl 1.4, w/tv-out,...
96 altos g310 linux redhat9.0 environment test item specifications cpu p4 3.6ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#:857996 p4 3.4ghz/800fsb/1mb prescott, mpga478, sl7b8, d-1 stepping, mm#: 857995 p4 3.2ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#: 857996 p4 3.0ghz/8...
Appendix b 97 asrc/1s 1ch ultra160 raid card lsi express500, 32/33mhz pci, i960rm-100, 32mb sdram, acer altos cd4.0, graphics card agp 8x graphices card (entry) ag200e4-d32 xabre 200/ 32mb ddr std agp 8x graphices card (middle) leadtek geforce fx5200, lr2967, 64mb, dual 350mhz, opengl 1.4, w/tv-out,...
98 altos g310 rathat linue advanced 3.0 environment test item specifications cpu p4 3.6ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#:857996 p4 3.4ghz/800fsb/1mb prescott, mpga478, sl7b8, d-1 stepping, mm#: 857995 p4 3.2ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#: 857996 p...
Appendix b 99 asrc/1s 1ch ultra160 raid card lsi express500, 32/33mhz pci, i960rm-100, 32mb sdram, acer altos cd4.0, graphics card agp 8x graphices card (entry) ag200e4-d32 xabre 200/ 32mb ddr std agp 8x graphices card (middle) leadtek geforce fx5200, lr2967, 64mb, dual 350mhz, opengl 1.4, w/tv-out,...
100 altos g310 netware 4.2 environment test item specifications cpu p4 3.6ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#:857996 p4 3.4ghz/800fsb/1mb prescott, mpga478, sl7b8, d-1 stepping, mm#: 857995 p4 3.2ghz/800fsb/1mb prescott, mpga478, sl7b9, d-1 stepping, mm#: 857996 p4 3.0ghz/800f...
Appendix b 101 asrc/1s 1ch ultra160 raid card lsi express500, 32/33mhz pci, i960rm-100, 32mb sdram, acer altos cd4.0, graphics card agp 8x graphices card (entry) ag200e4-d32 xabre 200/ 32mb ddr std agp 8x graphices card (middle) leadtek geforce fx5200, lr2967, 64mb, dual 350mhz, opengl 1.4, w/tv-out...
Appendix c 102 this section describes online technical support services available to help you repair your acer systems. If you are a distributor, dealer, asp or tpm, please refer your technical queries to your local acer branch office. Acer branch offices and regional business units may access our w...
103 appendix c.