1. DL manuals
  2. Acer
  3. Projector
  4. X1161 Series
  5. Service Manual

Acer X1161 Series Service Manual - Preface

Other manuals for X1161 Series: Buyer's Manual, Quick Start, Specifications
Manual is about: Acer Projector Service Manual

Summary of X1161 Series

  • Page 1

    Service manual si : tse: check: approved: date revise version description 2009.05.22 v1.0 initial issue 2009.06.25 v2.0 modify chapter 5 2009.08.06 v3.0 1. Add x1161’s extended models: x1161a, x1161n,x110 2. Update engineering spec. Of chapter 1 3. Modify chapter 4 2009.09.16 v4.0 1. Add x1261’s ext...

  • Page 2: Preface

    Confidential i x1161/x1261/x1161a/x1161n/x110/h5360 preface this manual is applied to x1161/x1261/x1161a/x1161n/x110/h5360 projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product. Your customers will appreciate the quick ...

  • Page 3

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential ii x1161/x1161a/x1161n/x110/x1261/h5360 comparison list models parts h5360 x1261 x1161 x1161a x1161n x110 name label 35.8er02h001 35.8cq03h001 35.8cp02h001 35.8cp07h001 35.8cp05h001 35.8cp10h001 main board 70.8er17gr01 70.8cq09gr01 70.8cp25gr01 70.8c...

  • Page 4: Table of Content

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential iii table of content chapter 1 introduction highlight 1-1 compatible mode 1-5 product overview 1-9 chapter 2 disassembly process & assembly process equipment needed & product overview 2-1 disassemble lamp cover module 2-2 disassemble lamp module 2-2 ...

  • Page 5

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential iv assemble bottom shielding 2-17 assemble interrupt switch 2-17 assemble lamp driver module 2-18 assemble lvps module 2-19 assemble blower 2-19 assemble system fan module 2-20 assemble focus ring 2-21 assemble zoom ring 2-21 assemble dmd chip and dm...

  • Page 6

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential v calibration 4-7 video performance 4-9 optical performance measure 4-10 others 4-12 chapter 5 firmware upgrade equipment needed 5-1 dlp composer lite setup procedure 5-2 usb driver upgrade procedure (for x1161 only) 5-4 firmware upgrade procedure 5-...

  • Page 7: Introduction

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 1-1 chapter 1 introduction 1-1 highlight no item description 1 dimensions (w x h x d) ● 268 mm x 192 mm x 80 mm 2 weight ● 3 tilt angle ● 2.7 degree with elevator mechanism 4 power supply ● universal ac 100 – 240 v ~ 50-60 hz with pfc input ● varianc...

  • Page 8

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 1-2 no item description 8 contrast ● engineering spec: for x1161/x1161n/x1161a/x110: • 2500: 1 full white with full power / full black with eco power (minimum; projection lens at tele mode) • 3600: 1 full white with full power / full black with eco p...

  • Page 9

    Confidential 1-3 x1161/x1261/x1161a/x1161n/x110/h5360 no item description 16 ti dmd ● ti dmd 0.55” 12° 2xlvds s450 svga digital mirror device (for x1161/x1161n/x1161a/x110) ● ti dmd 0.55” 12° 2xlvds s450 xga digital mirror device (for x1261) ● ti dmd 0.62” 12° s450 720p digital mirror device (for h5...

  • Page 10

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 1-4 no item description 21 terminal ● for x1161/1161a/x110: • vga in * 1: one d-sub 15-pin female connector for pc input and analog data ( component i/p, hdtv, rgb sync) • s-video * 1: one mini din 4-pin connector for s-video input connector • compos...

  • Page 11: 1-2 Compatible Mode

    Confidential 1-5 x1161/x1261/x1161a/x1161n/x110/h5360 no item description 22 input signal spec. ● hsync frequency 30~ 100 khz ● vsync frequency 50~ 85 hz ● video signal rgb (pc) • analog rgb 0.7vp-p, 75 ohm, separate ttl h,v sync • analog rgb 1vp-p, 75 ohm, sync. On green signal • analog rgb 0.7vp-p...

  • Page 12

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 1-6 compatibility resolution v.Frequency [hz] h.Frequency [khz] xga 1024 x 768 60 48.4 1024 x 768 70 56.5 1024 x 768 75 60.0 1024 x 768 85 68.7 sxga 1152 x 864 70 63.8 1152 x 864 75 67.5 1152 x 864 85 77.1 1280 x 1024 60 64.0 1280 x 1024 72 77.0 1280...

  • Page 13

    Confidential 1-7 x1161/x1261/x1161a/x1161n/x110/h5360 compatibility modes (vga analog) (for h5360) compatibility resolution v.Frequency [hz] h.Frequency [khz] (1) vga analog - pc signal vga 640 x 480 60 31.5 640 x 480 72 37.9 640 x 480 75 37.5 640 x 480 85 43.3 640 x 480 120 61.6 svga 800 x 600 56 3...

  • Page 14

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 1-8 compatibility resolution v.Frequency [hz] h.Frequency [khz] (2) vga analog - extended wide timing wxga 1280 x 768 60 47.8 1280 x 768 75 60.3 1280 x 768 85 68.6 1280 x 720 60 44.8 1280 x 800 60 49.6 1366 x 768 60 47.71 wxga+ 1440 x 900 60 55.9 wsx...

  • Page 15: 1-3 Product Overview

    Confidential 1-9 x1161/x1261/x1161a/x1161n/x110/h5360 1-3 product overview projector outlook front /upper side item description item description 1 ventilation (inlet) 6 lens cap 2 ventilation (outlet) 7 power button 3 remote control receivers 8 remote control 4 focus ring 9 zoom lever 5 zoom lens 10...

  • Page 16

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 1-10 item description item description 1 power socket below items are for x1261 only: 2 kensingtontm lock port 4 s-video input connector 3 pc analog signal/hdtv/component video input connector (vga in 1 or vga in) 5 composite video input connector be...

  • Page 17

    Confidential 1-11 x1161/x1261/x1161a/x1161n/x110/h5360 rear side (for h5360) item description item description 1 power socket 6 ypbpr input connector 2 kensingtontm lock port 7 s-video input connector 3 rs232 connector 8 composite video input connector 4 pc analog signal/hdtv/component video input c...

  • Page 18

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 1-12 remote control and control panel layout.

  • Page 19

    Confidential 1-13 x1161/x1261/x1161a/x1161n/x110/h5360 item icon function description 1 remote control receiver receives signals from remote control. 2 power refer to the “turning the projector on/off” section. 3 menu • press “menu” to launch the onscreen display (osd) menu, back to the previous ste...

  • Page 20

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 1-14 getting started connecting the projector item description item description 1 power cord 6 s-video cable 2 vga cable 7 audio cable jack/jack 3 composite video cable 8 audio cable jack/rca 4 rs232 cable 9 usb cable note: to ensure the projector wo...

  • Page 21

    Confidential 1-15 x1161/x1261/x1161a/x1161n/x110/h5360 system block diagram (for x1161/x1161a/x110).

  • Page 22

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 1-16 system block diagram (for x1261).

  • Page 23

    Confidential 1-17 x1161/x1261/x1161a/x1161n/x110/h5360 system block diagram (for h5360).

  • Page 24

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 1-18 bottom cover dimension.

  • Page 25

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-1 chapter 2 disassembly & assembly process 2-1 equipment needed & product overview 1. Screw bit (+): 105 2. Screw bit (+): 107 3. Screw bit (-): 107 4. Hex sleeves 5mm 5. Long nose nipper 6. Tweezers 7. Projector * before you start: this process is...

  • Page 26: 2-3  Disassemble Lamp

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-2 2-3 disassemble lamp module 1. Loosen 2 screws (as red circle) on the lamp module. 2. Take off the lamp module. 2-2 disassemble lamp cover module 1. Loosen 2 screws (as red circle) on the lamp cover. 2. Disassemble the lamp cover module..

  • Page 27: 2-5  Disassemble Top

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-3 2-5 disassemble top shielding 1. Unscrew 5 screws (as red circle) to disassemble the top shielding. 2-4 disassemble top cover module 1. Unscrew 2 screws (as red circle) from the bottom cover. 2. Remove the top cover module. Note: - when you remov...

  • Page 28: 2-6  Disassemble Front

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2- 2-6 disassemble front cover and ir sensor board 1. Unplug 1 connector (as yellow square). 2. Press two sides (as red arrows point) to unfasten 2 tenons (as green square). 3. Remove the front cover. 4. Tear off the mylar (as blue square). 5. Unscre...

  • Page 29: Module and Io Cover

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-5 2-7 disassemble main board module and io cover module 1. Tear off 3m tape (as green square). 2. Unplug 6 connectors (as yellow square). 3. Unscrew 2 screws (as red circle). Please refer to the table as below for details of each connector. Item ma...

  • Page 30

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-6 4. Unplug 1 connector (as blue square). 5. Disassemble the main board moudle. 6. Unscrew 2 screws (as green circle). Item male connector on main board the key feature figure d photo sensor compose of red/black/white wire and black wire tube (3 pi...

  • Page 31: 2-8  Disassemble Engine

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-7 note: circuit boards > 10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the circuit boards and follow local regulations for disposal. 7. Unscrew 4 hex screws (as blue circle). 8. Separate the main board an...

  • Page 32: 2-9  Disassemble Color

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2- note: circuit boards > 10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the circuit boards and follow local regulations for disposal. 2-9 disassemble color wheel module 1. Unscrew 2 screws (as red circle) t...

  • Page 33: 2-12 Disassemble Focus

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2- zoom ring zoom ring fixed holder 2-12 disassemble focus ring 1. Unscrew 3 screws (as red circle) to disassemble the focus ring. Focus ring 2-11 disassemble zoom ring 1. Unscrew 2 screws (as red circle) to disassemble the zoom ring and zoom ring fi...

  • Page 34: 2-13 Disassemble System

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-10 4. Unscrew 4 screws (as blue circle) to separate system fan and fan shielding. Note: - take the fan module as the right gesture. Fan shielding system fan 2-13 disassemble system fan module 1. Unscrew 3 screws (as red circle) to disassemble the f...

  • Page 35: 2-14 Disassemble Blower

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-11 2-14 disassemble blower 1. Unscrew 3 screws (as red circle). 2. Disassemble the blower. 2-15 disassemble lvps module 1. Unplug 2 connectors (as yellow square). 2. Unscrew 6 screws (as red circle). 3. Disassemble the lvps module and the ac inlet ...

  • Page 36: 2-16 Disassemble Lamp

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-12 2-16 disassemble lamp driver module 1. Unscrew 1 screw (as red circle) to disassemble the lamp driver module. 2. Unscrew 2 screws (as blue circle). 3. Unplug 3 connectors (as green square) to disassemble the cables from lamp driver module. 4. Un...

  • Page 37: 2-17 Disassemble Interrupt

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-13 2-17 disassemble interrupt switch 1. Unfasten 2 tenons (as green square) to disassemble the interrupt switch. 2-18 disassemble bottom shielding 1. Tear off the emi tapes (as yellow square). 1. Unscrew 2 screws (as red cricle) to disassemble the ...

  • Page 38: 2-19 Disassemble Speaker

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-1 2-19 disassemble speaker (for x1261/h5360) 1. Unfasten 2 tenons (as green square) as blue arrows point to disassemble the speaker. 2-20 rod adjustment 1. Environment adjustment - the distance between the engine and the screen is 2.38 m. - this pr...

  • Page 39: 2-21  Re-Write System and

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-15 2-21 re-write system and lamp usage hour 1. Get into service mode - press "power", "left", "left" and "menu" buttons sequentially to get into service mode. 2. Get into other settings mode - use "up" or "down" buttons to select "other settings", ...

  • Page 40: 2-22  Assemble Speaker

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-16 4. Re-write lamp hours (full power mode) - select "lamp hours adjust" and use "left" or "right" buttons to re-write the "lamp hours (full)". 5. Re-write lamp hours (eco mode) - select "lamp hours" and use "left" or "right" buttons to re-write th...

  • Page 41: 2-23 Assemble Bottom

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-17 2-23 assemble bottom shielding 1. Screw 2 screws (as red circle) to assemble the bottom shielding. 2. Stick the emi tapes (as yellow square). 2-24 assemble interrupt switch 1. Fasten 2 tenons (as green square) to assemble the interrupt switch..

  • Page 42: 2-25 Assemble Lamp Driver

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-1 2-25 assemble lamp driver module 1. Screw 4 screw (as yellow circle) to assemble the lamp driver module and lamp driver holder. 2. Plug 3 connectors (as green square) to assemble the cables on lamp driver module. 3. Screw 2 screws (as blue circle...

  • Page 43: 2-26 Assemble Lvps Module

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-1 2-26 assemble lvps module 1. Plug 1 connector (as green square). 2. Assemble the lvps module and the ac inlet bracket. 3. Screw 6 screws (as red circle). 4. Plug 2 connectors (as yellow square). 2-27 assemble blower 1. Assemble the blower. 2. Scr...

  • Page 44: 2-28 Assemble System

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-20 2-28 assemble system fan module 1. Screw 4 screws (as blue circle) to assemble system fan and fan shielding. 2. Assemble the system fan module. 3. Stick the emi tape (as green square). 4. Screw 3 screws (as red circle) to assemble the fan module...

  • Page 45: 2-29 Assemble Focus Ring

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-21 2-29 assemble focus ring 1. Screw 3 screws (as red circle) to assemble the focus ring. 2-30 assemble zoom ring 1. Screw 2 screws (as red circle) to assemble the zoom ring and zoom ring fixed holder..

  • Page 46: 2-31 Assemble Dmd Chip

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-22 2-31 assemble dmd chip and dmd board 1. Rotate the screw (as yellow circle) 180° clockwise to assemble the dmd board and dmd chip. 2. Screw 2 screws (as red circle) to assemble the heat sink and dmd module. Note: - avoid touching the dmd chip. -...

  • Page 47: 2-33 Assemble Engine

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-23 2-33 assemble engine module 1. Screw 4 screws (as yellow circle) to assemble the engine module. 2. Stick the emi gasket (as green square). 2-34 assemble io cover and main board module 1. Assemble the io cover and main board module. 2. Screw 4 he...

  • Page 48

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-2 3. Screw 2 screws (as green circle). 4. Assemble the main board module. 5. Plug 1 connector (as blue square). 6. Screw 2 screws (as red circle). 7. Plug 6 connectors (as yellow square). 8. Stick 3m tape (as green square) on the main boad module..

  • Page 49: 2-35 Assemble Ir Sensor

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-25 2-35 assemble ir sensor board and front cover 1. Assemble the ir sensor board and ir cap. 2. Screw 2 screws (as red circle). 3. Stick the mylar (as blue square). 4. Assemble the front cover. 5. Press two sides (as red arrows point) to fasten 2 t...

  • Page 50: 2-37 Assemble Top Cover

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-26 2-36 assemble top shielding 1. Screw 5 screws (as red circle) to assemble the top shielding. Note: avoid pressuring the speaker cable (as yellow square) when you assemble the top shielding. (for x1261/h5360) 2-37 assemble top cover moudle 1. Ass...

  • Page 51: 2-38 Assemble Lamp

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 2-27 2-38 assemble lamp moudle 1. Assemble the lamp module. 2. Tighten 2 screws (as red circle) on the lamp module. 2-39 assemble lamp cover module 1. Assemble the lamp cover module. 2. Tighten 2 screws (as red circle) on the lamp cover..

  • Page 52: Troubleshooting

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 3-1 chapter 3 troubleshooting 3-1 led lighting message message power led red blue input power plug flash on to off 100ms -- standby v -- power button on -- v lamp retry -- 0.5 second h(on), 0.5 second l(off) flashing power off (cooling state) 0.5 sec...

  • Page 53: 3-2 Main Procedure

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 3-2 3-2 main procedure no symptom procedure 1 no power - ensure the power cord and ac power outlet are securely connected - ensure all connectors are securely connected and aren’t broken - check lvps - check lamp driver - check main board 2 auto shut...

  • Page 54

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 3-3 no symptom procedure 4 no image - ensure the signal cable and source work (if you connect multiple sources at the same time, use the " source " button switch) - ensure all connectors are securely connected and aren’t broken - check main board - c...

  • Page 55

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 3-4 no symptom procedure 9 poor uniformity/ shadow - ensure the projection screen without dirt - ensure the projection lens is clean - ensure the brightness is within spec - check rod alignment - check engine module 10 dead pixel/dust (out of spec.) ...

  • Page 56

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 3-5 no symptom procedure 15 forgetting password (administrator password) - an unique universal password which is printed on the security card. This unique password is a back door of administrator password which will be accepted by projector anytime n...

  • Page 57: 4-1 Test Equipment Needed

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 4-1 chapter 4 function test & alignment procedure 4-1 test equipment needed - ibm pc with svga/xga resolution - dvd player with multi-system, equipped "component", "s-video","composite" and "hdmi". - hdtv source (480p, 720p, 1080i, 1080p) - minolta c...

  • Page 58: 4-4 Test Condition

    Confidential 4-2 x1161/x1261/x1161a/x1161n/x110/h5360 4-4 test condition - circumstance brightness: dark room less than 2.0 lux. - inspection distance: 1.8 m~2.5 m functional inspection. - screen size: 60 inches diagonal. - after repairing each unit, it should be run-in (refer to the below table). S...

  • Page 59: Defect Specification Table

    Confidential 4-3 x1161/x1261/x1161a/x1161n/x110/h5360 4-5 test inspection procedure update change parts main board firmware color wheel lamp module engine module edid lamp driver version update v v color wheel index v v pc calibration v v video calibration v v g sensor calibration v v reset lamp hou...

  • Page 60: 4-6 Pc Mode

    Confidential 4-4 x1161/x1261/x1161a/x1161n/x110/h5360 4-6 pc mode note: - when getting into function test, adjust the zoom ring and focus ring to guarantee the image maximum and clearest, then start to test. - test signal: analog 800 x 600 @60hz (for x1161); analog 1024 x 768 @60hz (for x1261); anal...

  • Page 61

    Confidential 4-5 x1161/x1261/x1161a/x1161n/x110/h5360 - test signal: 1024 x 768 @60hz - test pattern: gray 10 inspection item - bright pixel check criteria - bright pixel should be no more than 1 under bright pixel should be no more than 1 under gray 10 pattern. - adjacent pixels are unacceptable. -...

  • Page 62

    Confidential 4-6 x1161/x1261/x1161a/x1161n/x110/h5360 - ref. Defect specification table 6. Focus test procedure - test equipment: video generator - test signal: analog 1024 x 768 @60hz - test pattern: full screen inspection item - focus check criteria - from screen 2.38 m via visual to check the foc...

  • Page 63: 4-7 Calibration

    Confidential 4-7 x1161/x1261/x1161a/x1161n/x110/h5360 include support format with frequency and auto detected functional will be workable. 4-7 calibration 1. Pc calibration procedure - test equipment: video generator - once main board is changed. Pc calibration should be done as well. (1) test signa...

  • Page 64

    Confidential 4-8 x1161/x1261/x1161a/x1161n/x110/h5360 (1) calibration pattern should be in full screen mode. (2) please press "power", "left", "left" and "menu" buttons sequentially to get into service mode. (3) choose "analog settings", press “menu” button to access "video calibration for" correcti...

  • Page 65: 4-8 Video Performance

    Confidential 4- x1161/x1261/x1161a/x1161n/x110/h5360 4-8 video performance 1. Cvbs procedure - test equipment: dvd player - test signal: cvbs inspection item - video performance test inspection distance - 1.8 m ~2.5 m criteria - check any abnormal color, line distortion or any noise on the screen. 2...

  • Page 66

    Confidential 4-10 x1161/x1261/x1161a/x1161n/x110/h5360 - adjust the volume to maximum by using the remote controller. - check the sound from speaker. - check if the "mute" is normal. 5. Hdmi test (for h5360) procedure - test signal : 720p,1080i - test pattern : any pattern - equipment: dvd player wi...

  • Page 67

    Confidential 4-11 x1161/x1261/x1161a/x1161n/x110/h5360 2. Brightness procedure - full white pattern - use cl100 to measure brightness values of p1~p9. - follow the brightness formula to calculate brightness values. ☼ brightness formula avg. (p1~p9)*1.1m 2 criteria ● 1100 ansi lumen 3. Full on/full o...

  • Page 68: 4-10 Others

    Confidential 4-12 x1161/x1261/x1161a/x1161n/x110/h5360 4-10 others 1. Function inspection general - all osd functions must be checked for functionality. When osd menu is displayed, there shall be no visible peaking, ringing, streaking, or smearing artifacts on the screen. Factory default - the facto...

  • Page 69: Firmware Upgrade

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 5-1 chapter 5 firmware upgrade 5-1 equipment needed software: (ddp 2430 for x1161/x1261/x1161a/x1161n/x110) (ddp 2431 for h5360) - dlp composer lite 9.2 - firmware (*.Img) - library file (x1161 x1261 flashdeviceparameters) (library file has to put in...

  • Page 70: Procedure

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 5-2 5-2 dlp composer lite setup procedure 1. Choose "dlp composer lite v9.2 setup" program. 2. Click "next". 3. Read "license agreement". - choose "i accept and agree to be bound by all the terms and conditions of this license agreement". - click "ne...

  • Page 71

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 5-3 5. Click "next". 6. Click "next". 7. The program is executing "installing" status. 8. Click "finish"..

  • Page 72: 5-3 Usb Driver Upgrade

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 5-4 5-3 usb driver upgrade procedure (for x1161/ x1161a/x1161n/x110) 1. Set-up - hold on "power" button and plug in the power cord. - the power led lights red and blue simultaneously after 5 seconds, then loosen "power" button. - connect projector wi...

  • Page 73

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 5-5 5-4 firmware upgrade procedure 1. Set-up - hold on "power" button and plug in the power cord. - the power led lights red and blue simultaneously after 5 seconds, then loosen "power" button. - connect projector with pc by rs232 cable. (for x1261/h...

  • Page 74

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 5-6 5. Click "communications". - select "serial port". (for x1261/h5360) - select "usb". (for x1161/x1161a/x1161n/ x110) - select the com port which you are using. (for x1261/h5360) - click "configure". (for x1261/h5360) 6. For x1261/h5360: "serial p...

  • Page 75

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 5-7 9. Select "complete image download", then click "reset bus" to erase the flash memory. 10. If the fw is ready, click "start download" to execute the firmware upgrade. - click "yes". 11. It takes about several minutes, the firmware upgrade process...

  • Page 76: 5-5 Waveform Download

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 5-8 5-5 waveform download - hold on "power" button and plug in the power cord. - after 2 seconds, the power led will flash blue, then loosen "power" button. - after 5 seconds, the projector will automatically get into standby status. - waveform downl...

  • Page 77: Edid Upgrade

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 6-1 chapter 6 edid upgrade 6-1 edid introduction extended display identification data is a vesa standard data format that contains basic information about a display device and its capabilities, including vendor information, maximum image size, color ...

  • Page 78: 6-2 Equipment Needed

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 6-2 6-2 equipment needed software - edid program - edid file (*.Ini) hardware - projector - power cord for projector (42.53506g002) - vga cable (42.87305g102) - hdmi(m) to dvi(f) adapter (42.82b13g001) (for h5360) - dvi cable (42.83n06g001) (for h536...

  • Page 79: 6-3 Setup Procedure (Vga)

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 6-3 6-3 setup procedure (vga) 1. Connect all ports (1) connect p1 of fixture with com port of pc/laptop by rs232 cable. (2) connect p3 of fixture with vga port of projector by vga cable. (3) plug power adapter to jp1 of fixture. (4) plug power cord t...

  • Page 80: 6-4 Edid Key-In Procedure

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 6-4 6-4 edid key-in procedure 1. Execute edid program - double click "edid" to execute edid program. 2. Process (1) select the com port which you are using. (2) click "model". (3) select the source file (*.Ini). (4) click "open". (5) key in the seria...

  • Page 81

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 6-5 3. Change the cable to analog - when the message "please change the cable to analog" appear on the screen, click "ok". 4. When the edid program is completed, a message "ok" will appear on the screen. 5. Read edid "analog" information - in "read i...

  • Page 82

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential 6-6 6-5 un-lock snid and default language reset (1) hold on "power" button then plug in the power cord. Note: at this moment, power led flashes red or blue altemately about 2 seconds, then the power led flashes blue, then loosen "power" button. (2) a...

  • Page 83: D.C. X1161

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential appendix a (exploded image) d.C. X1161 note: this chapter is only designed to show the exploded image of the projector. For updated part numbers, please refer to rspl report. 25.

  • Page 84

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential item p/n description parts supply 1 70.8cp01g001 bottom module x1161 2 70.8cp08g001 engne module x1161 3 70.8cp07g001 fan shielding module x1161 4 70.8cp04g001 o module x1161 5 70.8cp03g001 front module x1161 sp.8cp01gc01 lamp module for projector x1...

  • Page 85: D.C. X1261

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential d.C. X1261 25.

  • Page 86

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential v item p/n description parts supply 1 70.8cq04g001 bottom module x1261 2 70.8cq03g001 engne module x1261 3 70.8cp07g001 fan shielding module x1161 4 70.8cq01g001 o module x1261 5 70.8cp03g001 front module x1161 sp.8cp01gc01 lamp module for projector ...

  • Page 87: I.D. X1161

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential v i.D. X1161.

  • Page 88

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential v item p/n description parts supply 70.8cp26gr01 assy bottom cover module x1161 (service) v 1 51.8cp02h001 bottom cover mn3600h x1161 2 52.88n07g001 adjustable foot rubber,ep721 3 86.0a123g024 hex nut m3*5.5*0.5p l2.4 ni 4 61.8cp06g001 bottom shieldi...

  • Page 89: Front Module

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential v front module item p/n description parts supply 1 51.88t24g001 front r cap for x1160e 2 80.8cp05g001 pcba ir sensor bd for x1161 v 3 51.8cp09h001 front cover mn3600h x1161 v 4 85.3a122g040 screw cap mech m2*4 ni 5 61.8cp14h001 acer logo for x1161 v ...

  • Page 90: Io Module X1161

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential v io module x1161.

  • Page 91

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential x item p/n description parts supply 1 61.8cp10g001 main shielding small tinplate x1161 70.8cp25gr01 assy main board module x1161 (service) v 2 80.8cp01g001 pcba man board for x1161 3 35.8cp01h001 label o x1161 4 51.8cp13g001 mylar main-bd to lvps x11...

  • Page 92: Io Module X1261

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential x io module x1261.

  • Page 93

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential x item p/n description parts supply 1 61.8cp09g001 main shielding tinplate x1161 70.8cq09gr01 assy main board module x1261 (service) v 2 80.8cq01g001 pcba man board for x1261 3 35.8cq02h001 label io base x1261 4 51.8cp13g001 mylar main-bd to lvps x11...

  • Page 94: Bottom Shielding Module

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential x bottom shielding module item p/n description parts supply 1 61.8cp06g001 bottom shielding secc x1161 2 61.8cp08g001 speaker brkt sus301 x1161 3 49.8cq01g001 speaker 2w 16ohm dab128 90mm x1261 v 4 52.8cp05g001 sponge speaker x1161.

  • Page 95: One- Fan Module

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential x one- fan module.

  • Page 96

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential xv item p/n description parts supply 1 49.8cp02g001 sunon 70*70*20mm axial fan, kde1207pkv1. Ms.B3001.Af.Gn v 2 61.88t05g041 shielding two fan pdg-dsu30 3 61.8an01g002 lamp blower duct x15 generic 4 85.1f123g260 screw pan mech e/sf m3*26 ni 5 85.1a12...

  • Page 97: Engine Module

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential xv engine module item p/n description parts supply 1 70.8cp09g001 assy optical engine module z15 (s450) (for x1161) 1 70.8cq02g001 assy optical engine module (for x1261) 2 51.8cp04h001 focus ring mn3600h x1161 v 3 51.8cp08h001 zoom ring mn3600h x1161...

  • Page 98: Assy Engine Module

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential xv assy engine module.

  • Page 99

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential xv item p/n description parts supply 1 23.8cp01g001 yo ym39 projection lens 1.1x zoom 2 70.8cp15g001 assy relay module z15 3 23.8ah20g001 condenser1 for a15w 70.8cp22gr01 assy engine module x1161 (service) v 70.8cq07gr01 assy engine module x1261 (ser...

  • Page 100: Assy Color Wheel Module Z15

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential xv assy color wheel module z15 item p/n description parts supply 1 61.8cp03g001 cw bracket secc x1161 2 80.8cp04g001 pcba photo sensor board for x1161 v 3 23.8ef19g001 yo 6s r81y41g84c31w52b71_he3 cw 4 85.1a126g040 screw pan mech m2.6*4 ni 5 51.82y29...

  • Page 101: Assy Lamp Driver Module

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential xx assy lamp driver module item p/n description parts supply 1 51.88t11g003 holder lamp drver for h5350 2 75.8ba01g002 assy osram lamp driver o6 mic 180w (gen5_panyu+e20.8) v 3 85.1a123g060 screw pan mech m3*6 ni 4 85.3a122g040 screw cap mech m2*4 ni...

  • Page 102: A.K.

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential xx a.K..

  • Page 103

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential xx item p/n description parts supply 1 42.87205g001 cable composite video 1.8m 3200mp 2 42.00200g002 cable vga 15p 1.8m blk ep739 3 42.00110g011 cable power cord 1.8m sp-60/is-14 uk dis- warning label 4 42.00120g011 cable power cord 1.8m sp-023/is-14...

  • Page 104: Appendix B

    Confidential x1161/x1261/x1161a/x1161n/x110/h5360 i appendix b i. Serial number system definition serial number format for projector (take x1261 for example) eyk0201001 915 00000 59 0 1 1 2 3 4 5 6 1 : eyk0201001 = part number 2 : 915 = date code (ex:2009 = 9, the fifteenth week of the year = 15) 3 ...

  • Page 105: II. Pcba Code Definition

    X1161/x1261/x1161a/x1161n/x110/h5360 confidential ii ii. Pcba code definition pcba code for projector a b xxx xxxxxxxxx cc xxx eeee 1 2 3 4 5 6 7 1 : id 2 : vendor code 3 : firmware version 4 : p/n 5 : mb version 6 : date code 7 : s/n.

  • Page 106: Appendix C

    Confidential x1161/x1261/x1161a/x1161n/x110/h5360 i appendix c rs232 function command summary table (for x1261/h5360) general command type (projector “receives” commands) no code (character) function feature 1 okokokokok\r power on 2 * 0 ir 001\r power on 3 * 0 ir 002\r power off 4 * 0 ir 004\r keys...

  • Page 107

    Confidential ii x1161/x1261/x1161a/x1161n/x110 no code (character) function feature 30 * 0 ir 036\r query native display resolution 31 * 0 ir 037\r query company name 32 * 0 ir 042\r keystone up 33 * 0 ir 043\r keystone down 34 * 0 ir 046\r zoom 35 * 0 ir 047\r e-key 36 * 0 ir 048\r color rgb 37 * 0...