1. DL manuals
  2. Airlink101
  3. Wireless Access Point
  4. APO1215
  5. Quick Installation Manual

Airlink101 APO1215 Quick Installation Manual

Other manuals for APO1215: Specifications, User Manual
Manual is about: Wireless N/A 5GHz 200mW Outdoor AP

Summary of APO1215

  • Page 1

    Wireless n/a 5ghz 200mw outdoor ap with 15dbi patch antenna model: apo1215 quick installation guide v.1.0

  • Page 2: 1. Before You Start

    1 1. Before you start 9 web browser : internet explorer (7.0 or above), firefox, safari 9 a computer with a network adapter properly installed 9 2 x rj-45 ethernet cable front panel rear panel 1. Reboot button : unscrew the screw and click reset button to restart system or reset to default configura...

  • Page 3

    2 apo1215 is a multiple mode system which can be configured either as a wireless gateway or an access point as desired. It also can be used as a wds link for ethernet network expansion. This section depicts different applications on router ap mode, ap mode, wds mode, cpe mode, bridge+universal repea...

  • Page 4: 2. Hardware Installation

    3 2. Hardware installation 2. Connect the opposite end of the rj-45 cable to the p+data out port on the power over ethernet injector 3. Connect one end of another rj-45 cable to the data in port on the power over ethernet injector 1. Connect one end of a rj-45 cable into the ap's poe connector 4. Co...

  • Page 5

    4 3. Configuring the access point note : 1. It is recommended that you configure the access point from a wired computer. Before the access point can be configured, if you connect the ap to your computer directly, you must manually assign a static ip address to your computer's network adapter in the ...

  • Page 6

    5 note : 1. To protect your network from any unauthorized access it is recommended to enable wireless encryption. 2. The examples below are for wpa2-psk. If you select wpa-psk or wpa2-psk, make sure your wireless adapters support wpa or wpa2. If your wireless adapters do not support wpa or wpa2, the...

  • Page 7: 4. Configuring For Wds Link

    6 4. Configuring for wds link note : 1. The system provides wds function on router ap mode, ap mode and wds mode. 2. Wds link requires at least 2 apo1215x. The two wire networks(lan) need the same subnet. 3. The wds link needs to be set at same channel and with same security type. 4. Please install ...

  • Page 8

    7 4. Click enable and enter the remote apo1215's mac address. Setting up the remote apo1215 (remote base station) 1. Copy down the 12 digit mac address of the main apo1215 (main base station). The mac address is on the device label or the overview page (status->overview) and wireless general setup p...

  • Page 9

    8 5. Configuring for client bridge note : 1. This section will walk you through the steps of sharing (bridging) an internet connection in one building, and extending that same internet to another building. 2. The “main base station” provide access point with ssid “main_ap” 3. The two wire networks(l...

  • Page 10

    9 setting up the client bridge (client station) 3. Click site survey button. The system will automatically scan and display the scan results of all ap existing near by the system 4. Use main_ap as an example here where the ap is encrypted via wpa2-psk/ aes security type. Click select button of the m...

  • Page 11

    10 note : 1. To verify wired network of client station can access main base station, use ping command to “192.168.2.254” 2. If you can not access main base station, verify the ip address of the wired client (pc or laptop) is in the same subnet with main base station. 8. Click status->remote ap, the ...

  • Page 12

    11 6. Configuring for universal wireless repeater note : 1. This section will walk you through the steps of sharing (bridging) an internet connection in one building, and extending that same internet to another building with repeat access point. 2. A repeater is just a very normal client which, at t...

  • Page 13

    12 note : 1. The channel of repeat ap should be the same with main base station. 2. To verify wireless clients can associate essid “repeater_main_ap” with wep key. 3. To verify wireless clients can use ping command to “192.168.2.254”. 4. If you can not access main base station, verify the ip address...

  • Page 14

    13 7. How to configure tcp/ip settings on your pc windows xp/2000 1. Go into the control panel, double-click the network connections icon and then right-click the local area connection icon and then click properties. 2. Click internet protocol (tcp/ip) and then click properties. Then click on use th...

  • Page 15: Technical Support

    14 technical support e-mail: support@airlink101.Com toll free: 1-888-746-3238 web site: www.Airlink101.Com *theoretical maximum wireless signal rate derived from ieee standard 802.11 specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of n...