1. DL manuals
  2. Airlink101
  3. Print Server
  4. APSUSB203
  5. Quick Installation Manual

Airlink101 APSUSB203 Quick Installation Manual

Other manuals for APSUSB203: User Manual
Manual is about: 3-Port Print Server

Summary of APSUSB203

  • Page 1

    Quick installation guide model # apsusb203 ver. 1a 3-port print server.

  • Page 2

    Connecting the print server section 1 warning: only a usb printer may be connected to the usb port of the print server. Connecting any other usb device to the print server may damage the print server. Note: do not plug the power cord to the print server until you have reached step 4 of this section....

  • Page 3

    Section 2 installing ps utility step 1 insert the provided cd and wait for the autorun screen to appear. Step 2 click on install ps utility. Step 3 click next. Note: if the autorun screen does not appear automatically, go to start, run, type d:\autorun.Exe (where d is the letter of your cd drive) an...

  • Page 4

    Step 4 click next. Step 5 click yes. Step 6 click finish..

  • Page 5

    Section 3 configuring network setting before configuring the print server’s network setting, please take note of your computer’s tcp/ip setting. Step 1 click on start, run, and type command (for windows 95/98/me) or cmd (for windows 2000/ xp) and click ok. Step 2 at the command prompt, type ipconfig...

  • Page 6

    Step 6 in the ip address field, enter a valid ip address, subnet mask, and default gateway that matches your local area network. For example: if your computer’s ip address is 192.168.1 .100, enter the same three numbers: 192.168.1 in the corresponding fields. Note: you can leave the last ip address ...

  • Page 7

    Verifying network connection section 4 step 1 run the ps utility by going to start, (all) programs, ps-utility, ps-utility v3.00. Step 2 make sure the print server is detected under the device name. Step 3 click on show web setup to display the print server’s web configuration utility. Step 4 verify...

  • Page 8

    Step 5 click on the tools link, select the port you want to test and click the test button. The print server will perform a low-level print test, bypassing the operating system layer. Note: your printer should print out a test page. If not, verify that the printer is powered on and all cables are se...

  • Page 9

    Section 5 running ps wizard warning: make sure you have installed the printer driver locally on every computer that will use the print server in your network before running the ps wizard. Otherwise, the ps wizard will not run properly. Be sure to run the ps wizard on all the computers that will use ...

  • Page 10

    Section 4 step 3 click next. Step 4 select the printer that is connected to the print server and click next..

  • Page 11

    Step 5 double-click on the print server, select the printer port that the printer is connected to and click next. Step 6 click finish and ok. (for windows 95/98/me, you’ll need to reboot the computer). Step 7 re-run the ps wizard and setup any remaining printer(s) that are connected to the print ser...

  • Page 12

    Section 6 performing operating system print test the final step in setting up the print server is to perform an operating system print test. Please note that the instructions below are for windows xp, but the steps are similar for all the other windows operating systems. Step 1 click on start, setti...

  • Page 13

    Section 7 technical support e-mail: support@airlink101.Com toll free: 1-888-746-3238 web site: www.Airlink101.Com you have successfully configured the print server for printing. For more information on how to use the web configuration utility or setup for mac os, please refer to the user’s manual in...

  • Page 14

    Copyright © 2006 airlink101. All rights reserved. Airlink101, the stylized airlink101 logo, specific product designations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of airlink101. All other produ...