Airlinkplus AML001 Quick Installation Manual
PCI Modem Card
Quick Installation
Note：
：
：
：
If you encounter any problem during the installation
process, please refer to Manual in the provided CD. For safety,
before installing and uninstalling your modem, please make sure
the telephone line is UNPLUGGED from your modem.
1. Hardware Installation
System Requirements
Before installation, please check the following requirements with
your equipment.
!
Pentium
®
III or above
!
32MB RAM or more
!
One available PCI slot
!
CD-ROM drive
!
Windows 95
®
/ 98
®
/ Me
®
/ NT4.0
®
/ 2000
®
/ XP
®
Installing the Card
1. With the power to your PC disconnected, remove the PC's
casing.
2. Press the modem card firmly into the PCI slot, and secure it
with screws to your PC.
3. Reinstall the casing on your PC.
Connecting Your Modem
1. Plug one end of the phone cord into LINE jack and the other
end to the wall phone jack.
2. When you are not using the modem, you can use a telephone
on the modem’s phone line. Plug your telephone’s cord into
the modem’s PHONE jack.
The figure below illustrates the typical connection of internal
modem card.
2. Driver Installation
Once the hardware installation is finished, turn on your computer
and the system should detect the modem upon startup. Insert the
provided CD into your CD-ROM drive to start driver installation.
For Windows 95
1. Start Windows 95. When Update Device Driver Wizard
screen appears, click Next.
2. Click Other Locations.
3. Click Browse to locate the path of the driver:
X:\Driver\Win9x (where X is your CD-ROM drive letter) and
click OK.
4. Windows will find the location of driver; click Finish.
5. When Insert Disk window appears, click OK.
6. Click Browse to locate the path of the driver:
X:\Driver\Win9x (where X is your CD-ROM drive letter) and
click OK.
7. Windows will continue to detect another device. Click Next.
8. Repeat steps 2-4 to complete installation.
For Windows 98
1. Start Windows 98. When Add New Hardware Wizard screen
appears, click Next.
2. Select Search for the best driver for your device and click
Next.
3. Check Specify a location. Click Browse to locate the path of
the driver: X:\Driver\Win9x (where X is your CD-ROM
drive letter) and click OK. Click Next.
4. Windows will find the location of driver; click Next.
5. Click Finish.
6. Windows will continue to detect another device. Click Next.
7. Repeat steps 2-5 to complete installation.
For Windows Me
1. Start Windows Me. When Add New Hardware Wizard
screen appears, select Specify the location of the driver and
click Next.
2. Select Search for the best driver for your device and then
check only the Specify a location box. Click Browse to locate
the path of the driver: X:\Driver\WinME (where X is your
CD-ROM drive letter) and click Next.
3. Windows will find the driver file for the device. Click Next.
4. Click Finish.
5. Windows will continue to detect another device. Repeat Steps
1-4.
6. When New Hardware Found message appears, wait for
Windows to complete the installation.
For Windows NT4.0
1. Click Start menu and then click Run. Click Browse to open
the file Setup.exe from X:\Driver\NT40 where X is your CD-
ROM drive letter and click OK.
2. When confirm message appears, click OK.
3. When prompted to restart your computer, click OK.
For Windows 2000
1. Start Windows 2000. Windows will detect a new hardware
device, click Next to continue.
2. Select Search for a suitable driver… and click Next.
3. Check ONLY Specify a location and click Next.
4. Click Browse to locate the path of the driver: X:\Driver\W2K
(where X is your CD-ROM drive letter) and click OK.
5. When Windows finds the location of the driver, click Next.
6. If Digital Signature Not Found window appears, click Yes to
continue.
7. Click Finish. When Found New Hardware window appears,
wait for Windows to complete the installation.