1. DL manuals
  2. AirLive
  3. Switch
  4. SNMP-24MGB
  5. User Manual

AirLive SNMP-24MGB User Manual

Manual is about: 24+8 Combo Pure Gigabit SNMP Managed Switch

Summary of SNMP-24MGB

  • Page 1

    Snmp-24mgb 24+8 combo pure gigabit snmp managed switch user’s manual.

  • Page 2: Copyright & Disclaimer

    Copyright and disclaimer airlive snmp-24mgb user’s manual copyright & disclaimer no part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of ovislink corp. Ovislink corp. Has made the best effort...

  • Page 4: Table of Contents

    Table of contents i airlive snmp-24mgb user’s manual table of contents 1. Introduction ................................................................................................1 1.1 overview..............................................................................................1 1.2 how...

  • Page 5

    Table of contents airlive snmp-24mgb user’s manual ii 4.3 port ....................................................................................................34 4.3.1 port configuration......................................................................................34 4.3.2 port status ......

  • Page 6

    Table of contents iii airlive snmp-24mgb user’s manual 4.11.2 port configuration ..................................................................................135 4.11.3 802.1x status.........................................................................................137 4.11.4 802.1x statis...

  • Page 7

    Table of contents airlive snmp-24mgb user’s manual iv 4.21.1 diag .......................................................................................................179 4.21.2 ping .......................................................................................................180 4.22 mai...

  • Page 8: Introduction

    1. Introduction 1 a irlive snmp-24mgb user’s manual 1 1. Introduction 1.1 overview the snmp-24mgb is a 24-port gigabit l2+ managed switch with 8-port gigabit tp/sfp slots and 16-port gigabit sfp slots. This switch can be used to build high-performance switched workgroup networks. The switch can be m...

  • Page 9

    1. Introduction airlive snmp-24mgb user’s manual 2 ip, username, and password. 3.3 management interface: this section introduces web management, and console management. 3.4 introduction to web management: this section tells you how to get into the webui using http. Chapter 4 : this chapter explains ...

  • Page 10: 1.4 Features

    1. Introduction 3 a irlive snmp-24mgb user’s manual 1.4 features confirms to ieee802.3 10base-t, 802.3u 100base-tx, 802.3ab 1000base-t, 802.3z gigabit fiber 16 x mini-gbic ports + 8 x 1000base-t/mini-gbic ports (combo) for optional fiber connection high back-plane bandwidth 48gbps 8k entry mac addre...

  • Page 11

    1. Introduction airlive snmp-24mgb user’s manual 4 supports default configuration which can be restored to overwrite the current configuration which is working on via web browser and cli supports on-line plug/unplug sfp modules supports quality of service (qos) for real time applications based on th...

  • Page 12: Installing The

    2. Installing the snmp-24mgb 5 airlive snmp-24mgb user’s manual 2 2. Installing the snmp-24mgb this chapter describes the hardware features and the hardware installation procedure for the snmp-24mgb. For software configuration, please go to chapter 3 for more details. 2.2 before you start it is impo...

  • Page 13: 2.4 Optional  Accessories

    2. Installing the snmp-24mgb airlive snmp-24mgb v2 user’s manual 6 rs-232 cable user guide (cd-rom) quick installation guide rack-mounted kit compare the contents of your snmp-24mgb package with the standard checklist above. If any item is missing or damaged, please contact your local dealer for ser...

  • Page 14: 2.6 Hardware  Installation

    2. Installing the snmp-24mgb 7 airlive snmp-24mgb user’s manual 2.5 knowing your snmp-24mgb below are descriptions and diagrams of the product: 2.6 hardware installation set the snmp-24mgb on a sufficiently large flat space with a power outlet nearby. The surface where you put your snmp-24mgb should...

  • Page 15

    2. Installing the snmp-24mgb airlive snmp-24mgb v2 user’s manual 8 2.6.2 rack-mounted installation the snmp-24mgb comes with a rack-mounted kid and can be mounted in an eia standard size, 19-inch rack. The snmp-24mgb can be placed in a wiring closet with other equipment. Perform the following steps ...

  • Page 16: 2.7 Led  Table

    2. Installing the snmp-24mgb 9 airlive snmp-24mgb user’s manual note: for proper ventilation, allow about at least 4 inches (10 cm) of clearance on the front and 3.4 inches (8 cm) on the back of the switch. This is especially important for enclosed rack installation. 2.6.3 power on connect the power...

  • Page 17

    2. Installing the snmp-24mgb airlive snmp-24mgb v2 user’s manual 10 led status description green power on power off power is not connected green the port is connecting with the device. Blink the port is receiving or transmitting data. Lnk/act off no device attached. Green in 1000mbps connection spee...

  • Page 18: 3.1 Important  Information

    3. Configuring the snmp-24mgb 11 airlive snmp-24mgb user’s manual the snmp-24mgb offers many different types of management interface. You can configure through web browser (http), console (terminal), cli. In this chapter, we will explain snmp-24mgb’s available management interfaces and how to get in...

  • Page 19: 3.3 Management Interface

    3. Configuring the snmp-24mgb airlive snmp-24mgb v2 user’s manual 12 you are ready now to configure the snmp-24mgb by using your pc. 3.3 management interface the snmp-24mgb can be configured using on the management interfaces below: web management (http): you can manage your snmp-24mgb by simply typ...

  • Page 20

    3. Configuring the snmp-24mgb 13 airlive snmp-24mgb user’s manual after finishing the parameter settings, click “ok“. When the blank screen shows up, press enter key to bring out the login prompt. Key in the “admin“(default value) for the user name and “airlive” for the password (use enter key to sw...

  • Page 21

    3. Configuring the snmp-24mgb airlive snmp-24mgb v2 user’s manual 14 use the telnet, please open the command line windows. Then type “telnet 192.168.1.1” to start. When asking for username and password, please enter “admin” as username and “airlive” as password. After you login successfully, the pro...

  • Page 22

    3. Configuring the snmp-24mgb 15 airlive snmp-24mgb user’s manual 3.4 introduction to web management the snmp-24mgb offers web management interfaces for users. Users can easily access and control snmp-24mgb via web browsers. The web-based management supports internet explorer 5.0. It is based on jav...

  • Page 23

    3. Configuring the snmp-24mgb airlive snmp-24mgb v2 user’s manual 16 3. The login screen appears. 4. Key in the user name and password. The default user name is “admin” and password is “airlive”. 5. Click “enter” or ”login”, then the home screen of the web-based management appears..

  • Page 24: Web Management In

    4. Web management in snmp-24mgb 17 airlive snmp-24mgb user’s manual in this chapter, we will explain all settings in web management interface. Please be sure to read through chapter 3’s “introduction to web management” first. 4.1 menu structure of snmp-24mgb the web management menu of snmp-24mgb is ...

  • Page 25

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 18 function and the system will be logged out automatically when no action on the device 3 minutes later. If off is chosen, the screen will keep as it is. Default is on. Side menu: all management functions will show in side menu, yo...

  • Page 26: 4.2 System

    4. Web management in snmp-24mgb 19 airlive snmp-24mgb user’s manual 4.2 system 4.2.1 ip configuration function name: system information function description: port mac qos acl root 802.1x stp mirroring alarm save/restore diagnostics logout vlan system gvrp snmp ip mac binding trunk mstp multicast dhc...

  • Page 27

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 20 show the basic system information. Parameter description: model name: the product name of this device. System description: the product description of this device. Location: basically, it is the location where this switch is put. ...

  • Page 28

    4. Web management in snmp-24mgb 21 airlive snmp-24mgb user’s manual current time: show the system time of the switch. Its format is day of week, month, day, hours : minutes : seconds, year. For instance, mon, march. 03, 14:54:07, 2008. Bios version: the version of the bios in this switch. Firmware v...

  • Page 29

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 22 up to 4 guest accounts can be created. The default setting for user account is: username: admin password: airlive 4.2.3 time configuration the switch provides manual and automatic ways to set the system time via ntp. Manual setti...

  • Page 30

    4. Web management in snmp-24mgb 23 airlive snmp-24mgb user’s manual parameter description: current time: show the current time of the system. Manual: this is the function to adjust the time manually. Filling the valid figures in the fields of year, month, day, hour, minute and second respectively an...

  • Page 31

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 24 daylight saving is adopted in some countries. If set, it will adjust the time lag or in advance in unit of hours, according to the starting date and the ending date. For example, if you set the day light saving to be 1 hour. When...

  • Page 32

    4. Web management in snmp-24mgb 25 airlive snmp-24mgb user’s manual ip configuration function description: set ip address, subnet mask, default gateway and dns for the switch. Parameter description: dhcp setting: the switch supports dhcp client used to get an ip address automatically if you set this...

  • Page 33

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 26 ip address: users can configure the ip settings and fill in new values if users set the dhcp function “disable”. Then, click button to update. When dhcp is disabled, default: 192.168.1.1 if dhcp is enabled, this field is filled b...

  • Page 34

    4. Web management in snmp-24mgb 27 airlive snmp-24mgb user’s manual dns: it is domain name server used to serve the translation between ip address and name address. The switch supports dns client function to re-route the mnemonic name address to dns server to get its associated ip address for access...

  • Page 35

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 28 parameter description: port no: display the port number. The number is 1 – 24. Detection port - enable: when port no. Is chosen, and enable port's loop detection, the port can detect loop happens. When loop happen, port will be l...

  • Page 36

    4. Web management in snmp-24mgb 29 airlive snmp-24mgb user’s manual rule 1: when no list exists, then it will accept all connections. Rule 2: when only “accept lists” exist, then it will deny all connections, excluding the connection inside of the accepting range. Rule 3: when only “deny lists” exis...

  • Page 37

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 30 the mode, users can be classified into two types: those who are able to connect to the switch (accept) and those who are unable to connect to the switch (deny). Some restrictions also can be placed on the mode that the user conne...

  • Page 38

    4. Web management in snmp-24mgb 31 airlive snmp-24mgb user’s manual incoming port: the switch supports two kinds of options for managed valid port range, including “any” and “custom”. Default is “any”. You can select the ports that you would like them to be worked and restricted in the management se...

  • Page 39

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 32 parameter description: no: display the order number that the trap happened. Time: display the time that the trap happened. Desc: display a description event recorded in the system log. Clear: clear log data. 4.2.8 virtual stack f...

  • Page 40

    4. Web management in snmp-24mgb 33 airlive snmp-24mgb user’s manual the most top-left button is only for master device. The background color of the button you press will be changed to represent that the device is under your management. Note: it will remove the grouping temporarily in case that you l...

  • Page 41: 4.3 Port

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 34 4.3 port port configuration , port status, simple counter and detail counter are contained in this function folder for port monitor and management. Each of them will be described in detail orderly in the following sections. 4.3.1...

  • Page 42

    4. Web management in snmp-24mgb 35 airlive snmp-24mgb user’s manual parameter description: port: to display the port index media: to display the port media type with utp or sfp speed: set the speed and duplex of the port. In speed, if the media is 1gbps fiber, it is always 1000mbps and the duplex is...

  • Page 43

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 36 media supports. Media type nway speed duplex 1000m tp on/off 10/100/1000m full for all, half for 10/100 1000m fiber on/off 1000m full in auto-negotiation mode, no default value. In forced mode, default value depends on your setti...

  • Page 44

    4. Web management in snmp-24mgb 37 airlive snmp-24mgb user’s manual function name: port status function description: report the latest updated status of all ports in this switch. When any one of the ports in the switch changes its parameter displayed in the page, it will be automatically refreshed t...

  • Page 45

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 38 parameter description: port: display the port number. The number is 1 – 24. Link: show that if the link on the port is active or not. If the link is connected to a working-well device, the link will show the link “up”; otherwise,...

  • Page 46

    4. Web management in snmp-24mgb 39 airlive snmp-24mgb user’s manual parameter description of port 1 ~ port 24: connector type: display the connector type, for instance, utp, sc, st, lc and so on. Fiber type: display the fiber mode, for instance, multi-mode, single-mode. Tx central wavelength: displa...

  • Page 47

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 40 4.3.3 simple counter the function of simple counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad. In below figure, the window can show all ports’ counter in...

  • Page 48

    4. Web management in snmp-24mgb 41 airlive snmp-24mgb user’s manual parameters description: packet: transmit: the counting number of the packet transmitted. Receive: the counting number of the packet received. Bytes: transmit: total transmitted bytes. Receive: total received bytes. Error: transmit: ...

  • Page 49

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 42 4.3.4 detail counter the function of detail counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad. In below figure, the window can show only one port counter...

  • Page 50

    4. Web management in snmp-24mgb 43 airlive snmp-24mgb user’s manual rx high priority packets: number of rx packets classified as high priority. Rx low priority packets: number of rx packets classified as low priority. Rx broadcast: show the counting number of the received broadcast packet. Rx multic...

  • Page 51

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 44 tx 65-127 bytes: number of 65 ~ 126-byte frames in good and bad packets transmitted. Tx 128-255 bytes: number of 127 ~ 255-byte frames in good and bad packets transmitted. Tx 256-511 bytes: number of 256 ~ 511-byte frames in good...

  • Page 52

    4. Web management in snmp-24mgb 45 airlive snmp-24mgb user’s manual the detail counts will be refreshed manually when user use mouse to click on “refresh” button. Clear: the detail counts will be reset to zero when user use mouse to click on “clear” button. 4.3.5 power saving this function provides ...

  • Page 53: 4.4 Vlan

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 46 parameter description: power saving: the parameter will enable or disable to verify switches have the ability to consider the length of any ethernet cable connected for adjustment of power usage accordingly. Shorter lengths requi...

  • Page 54

    4. Web management in snmp-24mgb 47 airlive snmp-24mgb user’s manual port-based: port-based vlan is defined by port. Any packet coming in or outgoing from any one port of a port-based vlan will be accepted. No filtering criterion applies in port-based vlan. The only criterion is the physical port you...

  • Page 55

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 48 the name defined by administrator is associated with a vlan group. Valid letters are a-z, a-z, 0-9, “ - “ and “_”. The maximal length is 15 characters. Vlan id: vlan identifier. Each tag-based vlan group has a unique vid. It appe...

  • Page 56

    4. Web management in snmp-24mgb 49 airlive snmp-24mgb user’s manual delete group: just press the button to remove the selected group entry from the tag-based group table. Note: if you need to use pvlan( private vlan) function on switch, you need follow the process as below: a. Create a vlan as prima...

  • Page 57

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 50 parameter description: vlan name: the name defined by administrator is associated with a vlan group. Valid letters are a-z, a-z, 0-9, “ - “ and “_” . The maximal length is 15 characters. Member port: this is used to enable or dis...

  • Page 58

    4. Web management in snmp-24mgb 51 airlive snmp-24mgb user’s manual 4.4.4 ports function name: vlan port configuration function description: in vlan tag rule setting, user can input vid number to each port. The range of vid number is from 1 to 4095. User also can choose ingress filtering rules to ea...

  • Page 59

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 52 port number. Vlan aware: based on ieee 802.1q vlan tag to forward packet ingress filtering: discard other vlan group packets, only forward this port joined vlan group packets frame type: all: forward all tagged and untagged packe...

  • Page 60

    4. Web management in snmp-24mgb 53 airlive snmp-24mgb user’s manual switches on the same vlan to restrict traffic flow. The apparatus comprises a switch having said plurality of ports, each port configured as a protected port or a non-protected port. An address table memory stores an address table h...

  • Page 61: 4.5 Mac

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 54 parameter description: vid: specific management vlan id. 4.5 mac mac table configuration gathers many functions, including mac table information, mac table maintenance, static forward, static filter and mac alias, which cannot be...

  • Page 62

    4. Web management in snmp-24mgb 55 airlive snmp-24mgb user’s manual parameter description: aging time: delete a mac address idling for a period of time from the mac table, which will not affect static mac address. Range of mac address aging time is 10-1000000 seconds. The default aging time is 300 s...

  • Page 63

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 56 4.5.2 static filter function name: static filter function description: static filter is a function that denies the packet forwarding if the packet’s mac address is listed in the filtering static filter table. User can very easily...

  • Page 64

    4. Web management in snmp-24mgb 57 airlive snmp-24mgb user’s manual specified port of the switch. Static forward table associated with a specified port of a switch is set up by manually inputting mac address and its alias name. When a mac address is assigned to a specific port, all of the switch’s t...

  • Page 65

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 58 there are three mac alias functions in this function folder, including mac alias add, mac alias edit and mac alias delete. You can click button to add/modify a new or an existed alias name for a specified mac address, or mark an ...

  • Page 66: 4.6 Gvrp

    4. Web management in snmp-24mgb 59 airlive snmp-24mgb user’s manual parameter description: type: dynamic or static. Vlan: vlan identifier. This will be filled only when tagged vlan is applied. Valid range is 1 ~ 4094. Mac address: display the mac address of one entry you selected from the searched m...

  • Page 67

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 60 ports associated with their attribute database and garp information propagation (gip) to communicate among switches and end stations. With gid information and gip, gvrp state machine maintain the contents of dynamic vlan registra...

  • Page 68

    4. Web management in snmp-24mgb 61 airlive snmp-24mgb user’s manual parameter description: gvrp state: this function is simply to let you enable or disable gvrp function. You can pull down the list and click the arrow key to choose “enable” or “disable”. Then, click the button, the system will take ...

  • Page 69

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 62 the mode here means the type of participant. There are two modes, normal participant and non-participant, provided for the user’s choice. Normal: it is normal participant. In this mode, the switch participates normally in garp pr...

  • Page 70

    4. Web management in snmp-24mgb 63 airlive snmp-24mgb user’s manual function name: gvrp counter function description: all gvrp counters are mainly divided into received and transmitted two categories to let you monitor the gvrp actions. Actually, they are garp packets. Parameter description: receive...

  • Page 71

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 64 transmitted: total gvrp packets: total garp bpdu is transmitted by the gvrp application. Invalid gvrp packets: number of invalid garp bpdu is transmitted by the gvrp application. Leaveall message packets: number of garp bpdu with...

  • Page 72: 4.7 Qos

    4. Web management in snmp-24mgb 65 airlive snmp-24mgb user’s manual parameter description: vid: vlan identifier. When gvrp group creates, each dynamic vlan group owns its vid. Valid range is 1 ~ 4094. Member port: those are the members belonging to the same dynamic vlan group. Edit administrative co...

  • Page 73

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 66 function name: port qos configuration function description: to configure each port qos behavior. Four qos queue per port with strict or weighted fair queuing scheduling. There are 24 qos control lists (qcl) for advance programmab...

  • Page 74

    4. Web management in snmp-24mgb 67 airlive snmp-24mgb user’s manual there are two scheduling method, strict priority and weighted fair. Default is strict priority. After you choose any of scheduling method, please click apply button to be in operation. Queue weighted: there are four queues per port ...

  • Page 75

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 68 qce configuration: the qcl consists of 12 qos control entries (qces) that are searched from the top of the list to the bottom of the list for a match. The first matching qce determines the qos classification of the frame. The qce...

  • Page 76

    4. Web management in snmp-24mgb 69 airlive snmp-24mgb user’s manual.

  • Page 77

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 70 parameter description: qcl#: qcl number : 1~24 qce type: ethernet type / vlan id / udp/tcp port / dscp / tos / tag priority ethernet type value: the configurable range is 0x600~0xffff. Well known protocols already assigned.

  • Page 78

    4. Web management in snmp-24mgb 71 airlive snmp-24mgb user’s manual ethertype values. The commonly used values in the ethertype field and corresponding protocols are listed below: ethertype (hexadecimal) protocol 0x0800 ip, internet protocol 0x0801 x.75 internet 0x0802 nbs internet 0x0803 ecma inter...

  • Page 79

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 72 dscp value: the configurable dscp value: 0~63 traffic class: low / normal / medium / high 4.7.3 rate limiters function name: rate limit configuration function description: each port includes an ingress policer, and an egress shap...

  • Page 80

    4. Web management in snmp-24mgb 73 airlive snmp-24mgb user’s manual parameter description: port #: port number. Ingress enabled: enable to limit ingress bandwidth by ingress rate. Ingress rate: the configurable ingress rate range is 500 kbps ~ 1000000 kbps or 1 mbps ~ 1000 mbps egress unit: there ar...

  • Page 81

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 74 the configurable egress rate range is 500 kbps ~ 1000000 kbps or 1 mbps ~ 1000 mbps shaper unit: there are two units for egress rate limit: kbps / mbps. 4.7.4 storm control function name: storm control configuration function desc...

  • Page 82

    4. Web management in snmp-24mgb 75 airlive snmp-24mgb user’s manual status: enable/disable selection: means enabled; means disabled rate(pps): refer to the following rate configurable value list, the unit is packet per second (pps). 1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1k / 2k / 4k / 8k ...

  • Page 83

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 76 finish qcl configuration: set up port policies set up typical network application rules set up tos precedence mapping set up vlan tag priority mapping next: go to next step. Cancel: abort current configuration back to previous st...

  • Page 84

    4. Web management in snmp-24mgb 77 airlive snmp-24mgb user’s manual parameter description: wizard again: click on the , back to qcl configuration wizard. Finish: when you click on finish>, the parameters will be set according to the wizard configuration and shown on the screen, then ask you to click...

  • Page 85

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 78 parameter description: audio and video: quicktime 4 server / msn messenger phone / yahoo messenger phone / napster / real audio games: blizzard battlenet (diablo2 and starcraft) / fighter ace ii / quake2 / quake3 /.

  • Page 86

    4. Web management in snmp-24mgb 79 airlive snmp-24mgb user’s manual msn game zone user definition: ethernet type / vlan id / udp/tcp port / dscp ethernet type value: type range: 0x600~0xffff vlan id: vlan id range: 1~4094 udp/tcp port: two mode: range / specific udp/tcp port range: port range: 0~655...

  • Page 87

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 80

  • Page 88

    4. Web management in snmp-24mgb 81 airlive snmp-24mgb user’s manual parameter description: qcl #: qos control list (qcl): 1~24.

  • Page 89

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 82 parameter description: qcl id: qos control list (qcl): 1~24 tos precedence 0~7 class: low / normal / medium / high.

  • Page 90

    4. Web management in snmp-24mgb 83 airlive snmp-24mgb user’s manual parameter description: qcl id: qos control list (qcl): 1~24 tag priority 0~7 class: low / normal / medium / high.

  • Page 91: 4.8 Snmp

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 84 4.8 snmp any network management system (nms) running the simple network management protocol (snmp) can manage the managed devices equipped with snmp agent, provided that the management information base (mib) is installed correctl...

  • Page 92

    4. Web management in snmp-24mgb 85 airlive snmp-24mgb user’s manual snmp configuration function description: this function is used to configure snmp settings, community name, trap host and public traps as well as the throttle of snmp. A snmp manager must pass the authentication by identifying both c...

  • Page 93: 4.9 Acl

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 86 own community name. Say, the community name for get only works for get function and can’t be applied to other function such as set and trap. Default snmp function: enable default community name for get: public default community n...

  • Page 94

    4. Web management in snmp-24mgb 87 airlive snmp-24mgb user’s manual function name: acl port configuration function description: the switch acl function support up to 128 access control entries (aces), using the shared 128 aces for ingress classification. You can create an ace and assign this ace for...

  • Page 95

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 88 rate limiter id range: 1~16. To select one of rate limiter id for this port, it will limit met acl packets by rate limiter id configuration. Port copy: disabled: disable to copy the met acl packets to specific port port number: 1...

  • Page 96

    4. Web management in snmp-24mgb 89 airlive snmp-24mgb user’s manual rate limiter id: id range: 1~16 rate(pps): 1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1k / 2k / 4k / 8k / 16k / 32k / 64k / 128k / 256k / 512k / 1024k 4.9.3 access control list function name: access control list function descr...

  • Page 97

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 90 insert an entry edit this entry move up this entry move down this entry.

  • Page 98

    4. Web management in snmp-24mgb 91 airlive snmp-24mgb user’s manual parameter description: frame type: range: any / ethernet type / arp / ipv4 any: it is including all frame type ethernet type: it is including all ethernet frame type arp: it is including all arp protocol frame type ipv4: it is inclu...

  • Page 99

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 92.

  • Page 100

    4. Web management in snmp-24mgb 93 airlive snmp-24mgb user’s manual.

  • Page 101

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 94.

  • Page 102

    4. Web management in snmp-24mgb 95 airlive snmp-24mgb user’s manual.

  • Page 103

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 96.

  • Page 104

    4. Web management in snmp-24mgb 97 airlive snmp-24mgb user’s manual.

  • Page 105

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 98.

  • Page 106

    4. Web management in snmp-24mgb 99 airlive snmp-24mgb user’s manual.

  • Page 107

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 100

  • Page 108

    4. Web management in snmp-24mgb 101 airlive snmp-24mgb user’s manual.

  • Page 109

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 102.

  • Page 110

    4. Web management in snmp-24mgb 103 airlive snmp-24mgb user’s manual.

  • Page 111

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 104.

  • Page 112

    4. Web management in snmp-24mgb 105 airlive snmp-24mgb user’s manual.

  • Page 113

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 106.

  • Page 114

    4. Web management in snmp-24mgb 107 airlive snmp-24mgb user’s manual.

  • Page 115

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 108 function name: ace configuration function description: the switch acl function support up to 128 access control entries (aces), using the shared 128 aces for ingress classification. You can create an ace and assign this ace for ...

  • Page 116

    4. Web management in snmp-24mgb 109 airlive snmp-24mgb user’s manual dmac filter: range: any / mc / bc / uc / specific any: it is including all destination mac address mc: it is including all multicast mac address bc: it is including all broadcast mac address uc: it is including all unicast mac addr...

  • Page 117

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 110 range: any / arp / rarp / other any: including all arp/rarp protocol frame types arp: including all arp protocol frame types rarp: including all rarp frame types other: including other frame types except arp/rarp protocol reques...

  • Page 118

    4. Web management in snmp-24mgb 111 airlive snmp-24mgb user’s manual the ingress arp frames where the source mac address is not equal smac under mac parameter setting 1: the ingress arp frames where the source mac address is equal smac address under mac parameter setting rarp dmac match: range: any ...

  • Page 119

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 112 ethernet: range: any / 0 / 1 any: both 0 and 1 0: the ingress arp/parp frames where hardware type is not equal to “0x100”. 1: the ingress arp/parp frames where hardware type is equal “0x100”. Ip parameters: (when frame type = ip...

  • Page 120

    4. Web management in snmp-24mgb 113 airlive snmp-24mgb user’s manual range: any / host / network any: including all source ip address host: only one specific source host ip address network: a specific ip subnet segment under the source ip mask sip address: default: 192.168.1.1 sip mask: default: 255...

  • Page 121

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 114 range: any / specific / range any: including all udp source ports specific: according to following source port no. Setting for ingress classification range: according to following source port range setting for ingress classifica...

  • Page 122

    4. Web management in snmp-24mgb 115 airlive snmp-24mgb user’s manual range: 0-65535 dest. Port filter: range: any / specific / range any: including all tcp destination ports specific: according to following dest. Port no. Setting for ingress classification range: according to following dest. Port ra...

  • Page 123

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 116 any: including all tcp psh case 0: the tcp control bit psh is 0 1: the tcp control bit psh is 1 tcp ack: tcp control bit ack: means acknowledgment field significant range: any / 0 / 1 any: including all tcp ack case 0: the tcp c...

  • Page 124

    4. Web management in snmp-24mgb 117 airlive snmp-24mgb user’s manual non-zero: including ipttl is non-zero zero: including ipttl is zero ip fragment: (ip fragmentation flag) controls datagram fragmentation together with the identification field. The flags indicate whether the datagram may be fragmen...

  • Page 125

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 118 vlan parameters: vlan id filter: range: any / specific any: including all vlan ids specific: according to following vlan id and tag priority setting for ingress classification vlan id: range: 1-4094 tag priority: range: any / 0-...

  • Page 126

    4. Web management in snmp-24mgb 119 airlive snmp-24mgb user’s manual 4.9.4 wizard function name: wizard function description: the wizard function provides 4 type of typical application for user easy to configure their application with acl function. Parameter description: please select an action: set...

  • Page 127

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 120

  • Page 128

    4. Web management in snmp-24mgb 121 airlive snmp-24mgb user’s manual.

  • Page 129

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 122.

  • Page 130

    4. Web management in snmp-24mgb 123 airlive snmp-24mgb user’s manual.

  • Page 131

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 124.

  • Page 132

    4. Web management in snmp-24mgb 125 airlive snmp-24mgb user’s manual parameter description: common server: dhcp / dns / ftp / http / imap / nfs / pop3 / samba / smtp / telnet / tftp instant messaging: google talk / msn messenger / yahoo messenger user definition: ethernet type / udp port / tcp port ...

  • Page 133

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 126.

  • Page 134: 4.10 Ip Mac Binding

    4. Web management in snmp-24mgb 127 airlive snmp-24mgb user’s manual parameter description: port # : 1-24 binding enabled: use the switch acl function to support ip/mac binding function, the maximum is up to 128 entries. Source mac address: xx-xx-xx-xx-xx-xx. For example: 00-40-c7-00-00-01 source ip...

  • Page 135

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 128 function description: the switch has ip-mac binding table. The maximum number of ip-mac binding table is 1024 entries. The creation of authorized users can be manually. User can enable or disable the function for all ports on th...

  • Page 136: 4.11 802.1X Configuration

    4. Web management in snmp-24mgb 129 airlive snmp-24mgb user’s manual parameters description: no: the index to display the ip mac binding dynamic entry mac: six-byte mac address : xx-xx-xx-xx-xx-xx. For example: 00-40-c7-00-00-01 ip: four-byte ip address: xxx.Xxx.Xxx.Xxx. For example: 192.168.1.100 p...

  • Page 137

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 130 according to ieee802.1x, there are three components implemented. They are authenticator, supplicant and authentication server shown in below figure. Supplicant: it is an entity being authenticated by an authenticator. It is used...

  • Page 138

    4. Web management in snmp-24mgb 131 airlive snmp-24mgb user’s manual in below figure, this is the typical configuration, a single supplicant, an authenticator and an authentication server. B and c is in the internal network, d is authentication server running radius, switch at the central location a...

  • Page 139

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 132 authenticator pae and authenticator will immediately respond eap-request/identity packet. 3. The authenticator always periodically sends eap-request/identity to the supplicant for requesting the identity it wants to be authentic...

  • Page 140

    4. Web management in snmp-24mgb 133 airlive snmp-24mgb user’s manual only multihost 802.1x is the type of authentication supported in the switch. In this mode, for the devices connected to this port, once a supplicant is authorized, the devices connected to this port can access the network resource ...

  • Page 141

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 134 this function is used to configure the global parameters for radius authentication in 802.1x port security application. Parameter description: authentication server server ip server: server ip address for authentication. Default...

  • Page 142

    4. Web management in snmp-24mgb 135 airlive snmp-24mgb user’s manual udp port: default port number is 1812 . Secret key: the secret key between authentication server and authenticator. It is a string with the length 1 – 31 characters. The character string may contain upper case, lower case and 0-9. ...

  • Page 143

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 136 parameters which are port control, reauthmax, txperiod, quiet period, reauthenabled, reauthperiod, max. Request, supptimeout, servertimeout and controlled direction. Mode: range: disable / normal / advanced / clientless disable:...

  • Page 144

    4. Web management in snmp-24mgb 137 airlive snmp-24mgb user’s manual quiet period(0-65535 s): a period of time during which we will not attempt to access the supplicant. Deafult: 60 seconds reauthenabled: choose whether regular authentication will take place in this port. Default: on reauthperiod(1-...

  • Page 145

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 138 show this port ieee 802.1x security current status: authorized or unauthorized 4.11.4 802.1x statistics function name: 802.1x port statistics port1 function description: show the ieee 802.1x authentication related counters for m...

  • Page 146: 4.12 Trunking Configuration

    4. Web management in snmp-24mgb 139 airlive snmp-24mgb user’s manual 4.12 trunking configuration the port trunking configuration is used to configure the settings of link aggregation. You can bundle more than one port with the same speed, full duplex and the same mac to be a single logical port, thu...

  • Page 147

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 140 groupid (also 1~8, this static groupid can be the same with another lacp groupid) to form a logic “trunked port”. The benefit of using static trunk method is that a port can immediately become a member of a trunk group without a...

  • Page 148

    4. Web management in snmp-24mgb 141 airlive snmp-24mgb user’s manual parameter description: port: port number: 1-24 method: this determines the method a port uses to aggregate with other ports. None: a port does not want to aggregate with any other port should choose this default setting. Lacp: a po...

  • Page 149

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 142 active lacp: this field is only referenced when a port’s trunking method is lacp. Active: an active lacp port begins to send lacpdu to its link partner right after the lacp protocol entity started to take control of this port. P...

  • Page 150

    4. Web management in snmp-24mgb 143 airlive snmp-24mgb user’s manual parameter description: aggregator: it shows the aggregator id (from 1 to 24) of every port. In fact, every port is also an aggregator, and its own aggregator id is the same as its own port no. Method: show the method a port uses to...

  • Page 151: 4.13 Stp Configuration

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 144 together the ports whose peer link partners are all on a single system. Each system supports lacp will be assigned a globally unique system identifier for this purpose. A system id is a 64-bit field comprising a 48-bit mac addre...

  • Page 152

    4. Web management in snmp-24mgb 145 airlive snmp-24mgb user’s manual parameter description: stp state: show the current stp enabled / disabled status. Default is “disabled”. Bridge id: show switch’s bridge id which stands for the mac address of this switch. Bridge priority: show this switch’s curren...

  • Page 153

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 146 current forward delay: show the current root bridge forward delay time. The value of forward delay time is set by root. The forward delay time is defined as the time spent from listening state moved to learning state or from lea...

  • Page 154

    4. Web management in snmp-24mgb 147 airlive snmp-24mgb user’s manual parameter description: spanning tree protocol: set 802.1w rapid stp function enable / disable. Default is “disable” bridge priority: the lower the bridge priority is, the higher priority it has. Usually, the bridge with the highest...

  • Page 155

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 148 forward delay: you can set the root bridge forward delay time. This figure is set by root bridge only. The forward delay time is defined as the time spent from listening state moved to learning state and also from learning state...

  • Page 156

    4. Web management in snmp-24mgb 149 airlive snmp-24mgb user’s manual parameter description: port status: it displays the current state of a port. We cannot manually set it because it displays the status only. There are three possible states. (according to 802.1w specification) z discarding state ind...

  • Page 157

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 150 path cost status. 802.1w rstp recommended value: (valid range: 1 – 200,000,000) 10 mbps: 2,000,000; 100 mbps: 200,000; 1 gbps: 20,000 default: 0 priority: priority here means port priority. Port priority and port number are mixe...

  • Page 158: 4.14 Mstp

    4. Web management in snmp-24mgb 151 airlive snmp-24mgb user’s manual 4.14 mstp the implementation of mstp is according to ieee 802.1q 2005 clause 13 – multiple spanning tree protocol. Mstp allows frames assigned to different vlans to follow separate paths, each based on an independent multiple spann...

  • Page 159

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 152 4.14.2 mstp region config function name: mstp region config function description: to configure the basic identification of a mstp bridge. Bridges participating in a common mst region must have the same region name and revision l...

  • Page 160

    4. Web management in snmp-24mgb 153 airlive snmp-24mgb user’s manual parameter description: instance id: every spanning tree instance need to have a unique instance id within 0~4095. Instance 0 (cist) always exists and can not be deleted. Additional spanning instances (mstis) can be added or deleted...

  • Page 161

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 154 instance configuration: fig. 3-157 to provision spanning tree performance parameters per instance. Port config: fig. 3-158 to provision spanning tree performance parameters per instance per port. Instance status: fig. 3-159 to s...

  • Page 162

    4. Web management in snmp-24mgb 155 airlive snmp-24mgb user’s manual max. Hops: 6-40sec. It’s a new parameter for the multiple spanning tree protocol. It is used in the internal spanning tree instances. “cist remaining hops” or “msti remaining hops” in the spanning tree protocol message would decrea...

  • Page 163

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 156 the same definition as in the rstp specification for the cist ports. Admin p2p: (auto/ true/ false) the same definition as in the rstp specification for the cist ports. Restricted role: (yes/ no) if “yes” causes the port not to ...

  • Page 164

    4. Web management in snmp-24mgb 157 airlive snmp-24mgb user’s manual force version: it shows the current spanning tree protocol version configured. Bridge max age: it shows the max age setting of the bridge itself. Bridge forward delay: it shows the forward delay setting of the bridge itself. Bridge...

  • Page 165

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 158 root path cost value from the point of view of the bridges inside the ist. Cist current max age: max age of the cist root bridge. Cist current forward delay: forward delay of the cist root bridge. Time since last topology change...

  • Page 166: 4.15 Mirror

    4. Web management in snmp-24mgb 159 airlive snmp-24mgb user’s manual “dsbl”(disable port), ”alt”(alternate port), “bkup”(backup port), “root”(root port) , “dsgn”(designated port), “mstr”(master port). The last 3 are possible port roles for a port to transit to forwarding state path cost: display cur...

  • Page 167

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 160 parameter description: port to mirror to: range: disabled / port 1-24 set the monitoring port. Port #: range: 1-24 select the monitored ports. Source enable: the source enable means the monitored port ingress traffic will be cop...

  • Page 168: 4.16 Multicast

    4. Web management in snmp-24mgb 161 airlive snmp-24mgb user’s manual the destination enable means the monitored port egress traffic will be copied to monitoring port. 4.16 multicast the function, multicast, is used to establish the multicast groups to forward the multicast packet to the member ports...

  • Page 169

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 162 parameter description: disable: to disable the igmp service on the switch. Proxy : to select and enable the igmp mode with a proxy on the switch. Snooping: to select and enable the igmp mode with a snooping on the switch. 4.16.2...

  • Page 170

    4. Web management in snmp-24mgb 163 airlive snmp-24mgb user’s manual the general query interval is the amount of time in seconds between igmp general query messages sent by the router (if the router is the querier on this subnet). Available value: 1-3600 sec general query response timeout : the gene...

  • Page 171

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 164 parameter description: host time out: the igmp snooping host query timeout field is the amount of time in seconds. Available value: 1-65535 sec fast leave : to evoke the port to become a fast leave port in igmp snooping service....

  • Page 172

    4. Web management in snmp-24mgb 165 airlive snmp-24mgb user’s manual parameter description: index: to display the igmp group membership index information. Group address: the switch supports managed valid igmp group membership ip address range, it will show effective ip range. The valid range is 224....

  • Page 173

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 166 multicast vlan registration (mvr) routes packets received in a multicast source vlan to one or more receive vlans. Clients are in the receive vlans and the multicast server is in the source vlan. Multicast routing has to be disa...

  • Page 174

    4. Web management in snmp-24mgb 167 airlive snmp-24mgb user’s manual parameter description: mvid: the switch supports two kinds of options for managed valid vlan vid, including “client” and “router”. Default is “disable”. When you choose “client”, you can fill in mvid number. The valid vid range is ...

  • Page 175

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 168 parameter description: mvid: the switch supports two kinds of options for managed valid vlan vid, including “client” and “router”. Default is “disable”. When you choose “custom”, you can fill in vid number. The valid vid range i...

  • Page 176: 4.17 Alarm Configuration

    4. Web management in snmp-24mgb 169 airlive snmp-24mgb user’s manual for igmp groups and members in the web user interface. Parameter description: index: to display the mvr group membership index information. Group address: the switch supports managed valid mvr group membership ip address range, it ...

  • Page 177

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 170 function name: events configuration function description: the trap events configuration function is used to enable the switch to send out the trap information while pre-defined trap events occurred. The switch offers 24 differen...

  • Page 178

    4. Web management in snmp-24mgb 171 airlive snmp-24mgb user’s manual 4.17.2 email parameter description: email: mail server: the ip address of the server transferring your email. Username: your username on the mail server. Password: your password on the mail server. Email address 1 – 6: email addres...

  • Page 179: 4.18 Dhcp Snooping

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 172 4.18 dhcp snooping 4.18.1 dhcp snooping state function name: dhcp snooping state function description: the addresses assigned to dhcp clients on unsecure ports can be carefully controlled using the dynamic bindings registered wi...

  • Page 180

    4. Web management in snmp-24mgb 173 airlive snmp-24mgb user’s manual parameter description: dhcp snooping state: the parameter which set to disabled or enabled the dhcp snooping function on the switch, the default is disabled. Note: to click apply > when you finish the configuration. 4.18.2 dhcp sno...

  • Page 181

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 174 trust port 2: it set a trust port 2 available port from 0 to 24. 0 is disabled. Trust vid: it set a trust vlan id available vid from 1 to 4094. Server ip: it set a trust dhcp server ip address for dhcp snooping. Option 82: it se...

  • Page 182: 4.19 Save / Store

    4. Web management in snmp-24mgb 175 airlive snmp-24mgb user’s manual parameter description: mac: to show the dhcp snooping client’s mac address. Vid: to show the dhcp snooping client’s vlan id. Port: to show the dhcp snooping client’s port. Ip: to show the dhcp snooping client’s ip address. Lease: t...

  • Page 183

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 176 working configuration: it is the configuration you are using currently and can be changed any time. The configurations you are using are saved into this configuration file. This is updated each time as you press button. ƒ user c...

  • Page 184

    4. Web management in snmp-24mgb 177 airlive snmp-24mgb user’s manual function description: save the current configuration as a start configuration file in flash memory. 4.19.3 save user function name: save as user configuration function description: save the current configuration as a user configura...

  • Page 185: 4.20 Export / Import

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 178 completing to restore the configuration, the system’s start configuration is updated and will be changed its system settings after rebooting the system. 4.20 export / import function name: export/ import function description: wi...

  • Page 186: 4.21 Diagnostics

    4. Web management in snmp-24mgb 179 airlive snmp-24mgb user’s manual 4.21 diagnostics three functions, including diagnostics, loopback test and ping test are contained in this function folder for device self-diagnostics. Each of them will be described in detail orderly in the following sections. 4.2...

  • Page 187

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 180 4.21.2 ping function name: ping test function description: ping test function is a tool for detecting if the target device is alive or not through icmp protocol which abounds with report messages. The switch provides ping test f...

  • Page 188: 4.22 Maintenance

    4. Web management in snmp-24mgb 181 airlive snmp-24mgb user’s manual 4.22 maintenance this chapter will introduce the reset and firmware upgrade function for the firmware upgrade and key parameters change system maintenance requirements. 4.22.1 reset device function name: reset device function descr...

  • Page 189: 4.23 Logout

    4. Web management in snmp-24mgb airlive snmp-24mgb v2 user’s manual 182 4.23 logout you can manually logout by performing logout function. In the switch, it provides another way to logout. You can configure it to logout automatically. Function name: logout function description: the switch allows you...

  • Page 190: Cli Management In

    5. Cli management in snm-24mgb 183 airlive snmp-24mgb user’s manual in this chapter, we will explain features that are available through console. For detailed descriptions on the concept and application of the settings, please refer to chapter 4. 5.1 connecting to the console port the console port i...

  • Page 191

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 184 after you login successfully, the prompt will be shown as “#“ if you are the first login person and your authorization is administrator; otherwise it may show “$“. See the following two figures. The former means you behave as an ...

  • Page 192: 5.3 Command of Cli

    5. Cli management in snm-24mgb 185 airlive snmp-24mgb user’s manual 5.3 command of cli to see the commands of the mode, please input “?” after the prompt, then all commands will be listed in the screen. All commands can be divided into two categories, including global commands and local commands. Gl...

  • Page 193

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 186 5.3.1 global command of cli end syntax: end description: back to the top mode. When you enter this command, your current position would move to the top mode. If you use this command in the top mode, you are still in the position ...

  • Page 194

    5. Cli management in snm-24mgb 187 airlive snmp-24mgb user’s manual none. Example: snmp-24mgb# alarm snmp-24mgb (alarm)# events snmp-24mgb (alarm-events)# end snmp-24mgb# exit syntax : exit description : back to the previous mode. When you enter this command, your current position would move back to...

  • Page 195

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 188 argument: none. Possible value: none. Example: snmp-24mgb# ip snmp-24mgb(ip)# help commands available: ------------>------------ set ip set ip,subnet mask and gateway set dns set dns enable dhcp enable dhcp, and set dns auto or m...

  • Page 196

    5. Cli management in snm-24mgb 189 airlive snmp-24mgb user’s manual numbers of records, given by the argument. Argument: [#]: show last number of history records. (optional) possible value: [#]: 1, 2, 3, …., 256 example: snmp-24mgb (ip)# history command history: 0. Trunk 1. Exit 2. Snmp-24mgb# trunk...

  • Page 197

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 190 syntax: logout description: when you enter this command via telnet connection, you would logout the system and disconnect. If you connect the system through direct serial port with rs-232 cable, you would logout the system and be...

  • Page 198

    5. Cli management in snm-24mgb 191 airlive snmp-24mgb user’s manual restoring ... Restore default configuration successfully press any key to reboot system. Restore user syntax: restore user description: to restore the startup configuration as user defined configuration. If restoring default success...

  • Page 199

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 192 none. Possible value: none. Example: snmp-24mgb # save start saving start... Save successfully snmp-24mgb # save user syntax: save user description: to save the current configuration as the user-defined configuration. When you en...

  • Page 200

    5. Cli management in snm-24mgb 193 airlive snmp-24mgb user’s manual 5.3.2 local command of cli z 802.1x set maxreq syntax : set maxreq description : the maximum number of times that the state machine will retransmit an eap request packet to the supplicant before it times out the authentication sessi...

  • Page 201

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 194 possible value: : 1 to 24 : 0 or 1 example: snmp-24mgb(802.1x)# set mode 2 1 snmp-24mgb(802.1x)# set port-control syntax : set port-control description : to set up 802.1x status of each port. Argument : : syntax 1,5-7, available ...

  • Page 202

    5. Cli management in snm-24mgb 195 airlive snmp-24mgb user’s manual argument : : syntax 1,5-7, available from 1 to 24 : timer , range 0-65535 possible value: : 1 to 24 : 0-65535, default is 60 example: snmp-24mgb(802.1x)# set quietperiod 2 30 set reauthenabled syntax : set reauthenabled description ...

  • Page 203

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 196 the number of reauthentication attempts that are permitted before the port becomes unauthorized. Argument : : syntax 1,5-7, available from 1 to 24 : max. Value , range 1-10 possible value: : 1 to 24 : 1-10, default is 2 example: ...

  • Page 204

    5. Cli management in snm-24mgb 197 airlive snmp-24mgb user’s manual a timer used by the backend authentication state machine in order to determine timeout conditions in the exchanges between the authenticator and the supplicant or authentication server. The initial value of this timer is either supp...

  • Page 205

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 198 description : a timer used by the backend authentication state machine in order to determine timeout conditions in the exchanges between the authenticator and the supplicant or authentication server. The initial value of this tim...

  • Page 206

    5. Cli management in snm-24mgb 199 airlive snmp-24mgb user’s manual show status description : to display the mode of each port. Argument : none possible value: none example: snmp-24mgb(802.1x)# show status port mode ====== ============ 1 disable 2 multi-host 3 disable 4 disable 5 disable 6 disable s...

  • Page 207

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 200 reauthmax : 2 txperiod : 30 quiet period : 60 reauthenabled : on reauthperiod : 120 max. Request : 2 supptimeout : 30 servertimeout : 30 port 2) mode : disabled port control : auto reauthmax : 2 txperiod : 30 quiet period : 60 re...

  • Page 208

    5. Cli management in snm-24mgb 201 airlive snmp-24mgb user’s manual syntax : show server description : show the radius server configuration argument : none possible value: none example: snmp-24mgb(802.1x)# show server authentication server ________________________________________ ip address: 192.168...

  • Page 209

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 202 : new account name possible value: a string must be at least 5 characters. Example: snmp-24mgb(account)# add aaaaa password: confirm password: snmp-24mgb(account)# del syntax: del description: to delete an existing account. Argum...

  • Page 210

    5. Cli management in snm-24mgb 203 airlive snmp-24mgb user’s manual none. Example: snmp-24mgb(account)# modify aaaaa username/password: the length is from 5 to 15. Current username (aaaaa):bbbbb new password: confirm password: username changed successfully. Password changed successfully. Show syntax...

  • Page 211

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 204 ace description: to display the ace configuration. Argument: : the access control rule index value possible value: none. Example: snmp-24mgb(acl)# ace 2 index: 2 rule: switch vid: any tag_prio: any dmac: any frame type: arp arp t...

  • Page 212

    5. Cli management in snm-24mgb 205 airlive snmp-24mgb user’s manual argument: : 1-24 : permit: 1, deny: 0 : 0-16 (0:disable) : 0-24 (0:disable) possible value: : 1-24 : 0-1 : 0-16 : 0-24 example: snmp-24mgb(acl)# action 5 0 2 2 snmp-24mgb(acl)# show port policy id action rate limiter port copy count...

  • Page 213

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 206 delete description: to delete the ace ( access control entry) configuration on the switch. Argument: : the access control rule index value possible value: none. Example: snmp-24mgb(acl)# delete 1 snmp-24mgb(acl)# move syntax: mov...

  • Page 214

    5. Cli management in snm-24mgb 207 airlive snmp-24mgb user’s manual : 1-24 possible value: : 1-8 : 1-24 example: snmp-24mgb(acl)# policy 3 10 snmp-24mgb(acl)# ratelimiter syntax: ratelimiter description: to set access control rule with rate limiter on switch argument: : 1-16 : 1,2,4,8,16,32,64,128,2...

  • Page 216

    5. Cli management in snm-24mgb 209 airlive snmp-24mgb user’s manual argument: none possible value: none example: snmp-24mgb(acl)# show port policy id action rate limiter port copy counter a class map .. .. ……. …. … .. 5 1 deny 2 2 23 1 permit 0 0 0 24 1 permit 0 0 0 rate limiter rate(pps) ----------...

  • Page 217

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 210 possible value: : 1 to 6 example: snmp-24mgb(alarm-email)# del mail-address 2 del server-user syntax : del server-user description : to remove the configuration of server, user account and password. Argument : none. Possible valu...

  • Page 218

    5. Cli management in snm-24mgb 211 airlive snmp-24mgb user’s manual description : to set up the ip address of the email server. Argument : :email server ip address or domain name possible value: none. Example: snmp-24mgb(alarm-email)# set server 192.168.1.6 set user syntax : set user description : t...

  • Page 219

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 212 email address 1: abc@mail.Abc.Com email address 2: email address 3: email address 4: email address 5: email address 6: > del all syntax : del all description : to disable email and trap of events. Argument : :del the range of eve...

  • Page 220

    5. Cli management in snm-24mgb 213 airlive snmp-24mgb user’s manual del trap syntax : del trap description : to disable the trap of the events. Argument : :del the range of trap, syntax 1,5-7 possible value: : 1~24 example: snmp-24mgb(alarm-events)# del trap 1-3 set all syntax : set all description ...

  • Page 221

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 214 snmp-24mgb(alarm-events)# set email 1-3 set trap syntax : set trap description : to enable the trap of the events. Argument : :set the range of trap, syntax 1,5-7 possible value: : 1~24 example: snmp-24mgb(alarm-events)# set trap...

  • Page 222

    5. Cli management in snm-24mgb 215 airlive snmp-24mgb user’s manual 8 module inserted 9 module removed 10 dual media swapped 11 looping detected 12 stp disabled 13 stp enabled 14 stp topology changed 15 lacp disabled 16 lacp enabled 17 lacp member added 18 lacp aggregates port failure 19 gvrp disabl...

  • Page 223

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 216 z autologout autologout syntax : autologout description : to set up the timer of autologout. Argument : : range 1 to 3600 seconds, 0 for autologout off, current setting is 180 seconds. Possible value: : 0,1-3600 example: snmp-24m...

  • Page 224

    5. Cli management in snm-24mgb 217 airlive snmp-24mgb user’s manual export successful. Import syntax : import description : to run the import start function. Argument : none possible value: none example: snmp-24mgb(config-file)# import current 192.168.1.63 import successful. Z firmware upgrade synta...

  • Page 225

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 218 z gvrp set state syntax : set state description : to disable/ enable the gvrp function. Argument : 0 : disable the gvrp function 1 : enable the gvrp function possible value: 0 : disable the gvrp function 1 : enable the gvrp funct...

  • Page 226

    5. Cli management in snm-24mgb 219 airlive snmp-24mgb user’s manual : 1 to 24 example: snmp-24mgb(gvrp)# group applicant 2 5 0 gvrp group information current dynamic group number: 1 vid member port ---- -------------------------------------------------- 2 5.

  • Page 227

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 220 set applicant syntax : set applicant description : to set default applicant mode for each port. Argument : : port range, syntax 1,5-7, available from 1 to 24 : set applicant as normal mode : set applicant as non-participant mode ...

  • Page 228

    5. Cli management in snm-24mgb 221 airlive snmp-24mgb user’s manual set restricted syntax : set restricted description : to set the restricted mode for each port. Argument : : port range, syntax 1,5-7, available from 1 to 24 : set restricted normal : set restricted fixed : set restricted forbidden p...

  • Page 229

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 222 : 22 20 60 1000 normal normal disable 23 20 60 1000 normal normal disable 24 20 60 1000 normal normal disable set timer syntax : set timer description : to set gvrp join time, leave time, and leaveall time for each port. Argument...

  • Page 230

    5. Cli management in snm-24mgb 223 airlive snmp-24mgb user’s manual none possible value: none example: snmp-24mgb(gvrp)# show gvrp state: enable port join time leave time leaveall time applicant registrar restricted ---- --------- ---------- ------------- --------------- --------- ---------- 1 20 60...

  • Page 231

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 224 received total gvrp packets : 0 invalid gvrp packets : 0 leaveall message : 0 joinempty message : 0 joinin message : 0 leaveempty message : 0 empty message : 0 transmitted total gvrp packets : 0 invalid gvrp packets : 0 leaveall ...

  • Page 232

    5. Cli management in snm-24mgb 225 airlive snmp-24mgb user’s manual z hostname hostname syntax : hostname description : to set up the hostname of the switch. Argument : : hostname, max. 40 characters. Possible value: : hostname, max. 40 characters. Example: snmp-24mgb# hostname company company# z ig...

  • Page 233

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 226 syntax : set erp description : set router ports to enable argument : : syntax 1,5-7, available from 1 to 24 possible value: : 1 to 24 example: snmp-24mgb(igmp)# set erp 1 set flood syntax : set flood description : to set up disab...

  • Page 234

    5. Cli management in snm-24mgb 227 airlive snmp-24mgb user’s manual show igmpp syntax : show igmpp description : to display igmp proxy setting argument : none. Possible value: none. Example: snmp-24mgb(igmp)# show igmpp z ip disable dhcp syntax : disable dhcp description : to disable the dhcp functi...

  • Page 235

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 228 enable dhcp description : to enable the system dhcp function and set dns server via manual or auto mode. Argument : : set dhcp by using manual or auto mode. Possible value: : manual or auto example: snmp-24mgb(ip)# enable dhcp ma...

  • Page 236

    5. Cli management in snm-24mgb 229 airlive snmp-24mgb user’s manual : default gateway possible value: : 192.168.1.2 or others : 255.255.255.0 or others : 192.168.1.253 or others example: snmp-24mgb(ip)# set ip 192.168.1.2 255.255.255.0 192.168.1.253 show syntax : show description : to display the sy...

  • Page 237

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 230 set entry syntax : set entry description : to set ip mac binding entry argument : : 0 : client , 1: server : mac address : ip address : syntax 1,5-7, available from 1 to 24 : vlan id, 1 to 4094 possible value: : 0 : client , 1: s...

  • Page 238

    5. Cli management in snm-24mgb 231 airlive snmp-24mgb user’s manual none example: snmp-24mgb(ip_mac_binding)# delete ip 1 192.168.2.2 set state syntax : show description : to display the mac alias entry. Argument : none possible value: none example: snmp-24mgb(mac-table-alias)# show mac alias list m...

  • Page 239

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 232 :1 to 24 example: snmp-24mgb(loop-detection)# disable 1-24 snmp-24mgb(loop-detection)# show detection port locked port port status port status --------------------------------- 1 disable 1 normal 2 disable 2 normal 3 disable 3 no...

  • Page 240

    5. Cli management in snm-24mgb 233 airlive snmp-24mgb user’s manual 5 enable 5 normal 6 enable 6 normal 7 enable 7 normal 8 enable 8 normal …………. Resume syntax : resume description : to resume locked ports on switch. Argument : : set up the range of the ports to search for, syntax 1,5-7, available f...

  • Page 241

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 234 argument : none possible value: none example: snmp-24mgb(loop-detection)# show detection port locked port port status port status --------------------------------- 1 enable 1 normal 2 enable 2 normal 3 enable 3 normal 4 enable 4 ...

  • Page 242

    5. Cli management in snm-24mgb 235 airlive snmp-24mgb user’s manual snmp-24mgb(mac-alias)# set 23-56-r5-55-3f-03 test3 snmp-24mgb(mac-alias)# show mac alias no mac alias =========================================== 1 23-56-00-55-3f-03 test3 2 23-56-00-55-ef-03 test13 3 23-56-00-55-ef-33 test1 snmp-24...

  • Page 243

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 236 no mac alias =========================================== 1 23-56-00-55-3f-03 test3 2 23-56-00-55-ef-03 test13 3 23-56-00-55-ef-33 test1 show syntax : show description : to display mac alias entry. Argument : none possible value: ...

  • Page 244

    5. Cli management in snm-24mgb 237 airlive snmp-24mgb user’s manual to del dynamic mac entry. Argument : none possible value: none example: snmp-24mgb(mac-mac-table)# flush snmp-24mgb(mac-mac-table)# show no type vlan mac port members -----------------------------------------------------------------...

  • Page 245

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 238 set age-time syntax : set age-time description : to set mac table age out time of dynamic learning mac. Argument : : age-timer in seconds, 0, 10 1000000. The value zero disables aging possible value: : 0, 10 to 1000000. Example: ...

  • Page 246

    5. Cli management in snm-24mgb 239 airlive snmp-24mgb user’s manual 16 auto 17 auto 18 auto 19 auto 20 auto 21 auto 22 auto 23 auto 24 auto set learning syntax : set learning description : to set mac table learning. Argument : : 1,5-7, available from 1 to 24 : auto learning : disable learning : lear...

  • Page 247

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 240 mac table learning port learning mode- 2 auto 3 auto 4 auto 5 auto 6 auto 7 auto 8 auto 9 auto 10 auto 11 auto 12 auto 13 auto 14 auto 15 auto 16 auto 17 auto 18 auto 19 auto 20 auto 21 auto 22 auto 23 auto 24 auto show syntax : ...

  • Page 248

    5. Cli management in snm-24mgb 241 airlive snmp-24mgb user’s manual noneq possible value: none example: snmp-24mgb(mac-maintenance)# show 1 static aging configuration:ff 1,2,3,4,5,6,7,8,9 age time: 3004,15,16,17,1 mac table learning port learning mode 2 auto 3 auto 4 auto 5 auto 6 auto 7 auto 8 auto...

  • Page 249

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 242 > add syntax : add [alias] description : to add the static mac entry. Argument : : mac address, format: 00-02-03-04-05-06 : 0-24. The value “0” means this entry is filtering entry : vlan id. 0, 1-4094. Vid must be zero if vlan mo...

  • Page 250

    5. Cli management in snm-24mgb 243 airlive snmp-24mgb user’s manual : mac address, format: 00-02-03-04-05-06 : vlan id. 0, 1-4094. Vid must be zero if vlan mode is not tag-based possible value: : mac address : 0, 1-4094 example: snmp-24mgb(mac-static-mac)# del 00-02-03-04-05-06 0 snmp-24mgb(mac-stat...

  • Page 251

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 244 none possible value: none example: snmp-24mgb(mac-static-mac)# show forward static forwarding etnry: (total 1 item(s)) 1) mac: 00-02-03-04-05-06, port: 3, vid: -, alias: aaa snmp-24mgb(mac-static-mac)# z mirror set mirror syntax ...

  • Page 252

    5. Cli management in snm-24mgb 245 airlive snmp-24mgb user’s manual monitoring port. Argument : : the port that is chosen for monitored port of the mirror function, syntax 1,5-7, available from 1 to 24 possible value: : 1 to 24 example: snmp-24mgb(mirror)# set monitor-destination 2-15 snmp-24mgb(mir...

  • Page 253

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 246 to set up the monitoring port of the mirror function. User can observe the packets that the monitored port received via this port. Argument : : the monitoring port that is chosen for the mirror function. Only one port is allowed ...

  • Page 254

    5. Cli management in snm-24mgb 247 airlive snmp-24mgb user’s manual 22 23 24 snmp-24mgb(mirror)# show syntax : show description : to display the setting status of mirror configuration. Argument : none possible value: none example: snmp-24mgb(mirror)# show port to mirror to: 1 port source enable dest...

  • Page 255

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 248 14 v 15 v 16 17 18 v 19 20 21 22 23 24 snmp-24mgb(mirror)# z mstp disable syntax : disable description : to disable mstp function. Argument : none possible value: none example: snmp-24mgb(mstp)# disable enable syntax : enable.

  • Page 256

    5. Cli management in snm-24mgb 249 airlive snmp-24mgb user’s manual description : to enable mstp function. Argument : none possible value: none example: snmp-24mgb(mstp)# enable migrate-check syntax : migrate-check description : to force the port to transmit rst bpdus. Argument : usage: migrate-chec...

  • Page 257

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 250 : available from 6 to 40. Recommended value is 20 : available from 4 to 30. Recommended value is 15 : available from 6 to 40. Recommended value is 20 possible value: : available from 6 to 40. Recommended value is 20 : available f...

  • Page 258

    5. Cli management in snm-24mgb 251 airlive snmp-24mgb user’s manual description : to set port path cost per instance argument : syntax: 1,5-7, available from 1 to 24 : 0, 1-200000000. The value zero means auto status possible value: : available from 1 to 24 : the value zero means auto status, 0-2000...

  • Page 259

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 252 description : to set per port hello time argument : : syntax: 1,5-7, available from 1 to 24 : only 1~2 are valid values possible value: : syntax: 1,5-7, available from 1 to 24 : only 1~2 are valid values example: snmp-24mgb(mstp)...

  • Page 260

    5. Cli management in snm-24mgb 253 airlive snmp-24mgb user’s manual description : to set instance priority argument : : 0->cist; 1-4095->msti : must be a multiple of 4096,available from 0 to 61440 possible value: : 0->cist; 1-4095->msti : 0 to 61440 example: snmp-24mgb(mstp)# set priority 0 4096 snm...

  • Page 261

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 254 set r-role syntax : set r-role description : to set per port restricted role argument : syntax: 1,5-7, available from 1 to 24 : 0->false,1->true possible value: : 1 to 24 : 0->false,1->true example: snmp-24mgb(mstp)# set r-role 8...

  • Page 262

    5. Cli management in snm-24mgb 255 airlive snmp-24mgb user’s manual 16 discarding dsbl 2000000 128 2/2 v 17 discarding dsbl 2000000 128 2/2 v 18 discarding dsbl 2000000 128 2/2 v 19 discarding dsbl 2000000 128 2/2 v 20 discarding dsbl 2000000 128 2/2 v 21 discarding dsbl 2000000 128 2/2 v 22 discard...

  • Page 263

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 256 5 0 128 2 true auto false false 6 0 128 2 true auto false false 7 0 128 2 true auto false false 8 0 128 2 true auto true false 9 0 128 2 true auto true true 10 0 128 2 true auto true true 11 0 128 2 true auto true false 12 0 128 ...

  • Page 264

    5. Cli management in snm-24mgb 257 airlive snmp-24mgb user’s manual snmp-24mgb(mstp)# set region-name test2 snmp-24mgb(mstp)# show region-info name : test2 revision : 0 instances : 0 snmp-24mgb(mstp)# set revision-level syntax : set rev description : to set mstp revision-level(0~65535) argument : :0...

  • Page 265

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 258 argument : :0~65535 possible value: :0~65535 example: snmp-24mgb(mstp)# set version mstp show instance syntax : show instance description : to show instance status argument : :0->cist;1-4095->msti possible value: :0->cist;1-4095-...

  • Page 266

    5. Cli management in snm-24mgb 259 airlive snmp-24mgb user’s manual cist internal root path cost : 0 cist current max age : 20 cist current forward delay : 15 time since last topology change(secs) : 2569 topology change count(secs) : 0 snmp-24mgb(mstp)# show pconf syntax : show pconf description : t...

  • Page 267

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 260 15 0 128 2 true auto false true 16 0 128 2 true auto false true 17 0 128 2 true auto true true 18 0 128 2 true auto true true 19 0 128 2 true auto true true 20 0 128 2 true auto true true 21 0 128 2 true auto true false 22 0 128 ...

  • Page 268

    5. Cli management in snm-24mgb 261 airlive snmp-24mgb user’s manual none possible value: none example: snmp-24mgb(mstp)# show region-info name : test2 revision : 30000 instances : 0 snmp-24mgb(mstp)# show vlan-map syntax : show vlan-map description : to show vlan mapping of an instance argument : :0...

  • Page 269

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 262 add [name ] [ip ] [port ] [type ] action description : to add a new management policy entry. Argument : synopsis: add name george ip 192.168.1.1-192.168.1.90 port 2-5,8 type h,s action a synopsis: add name mary ip 192.168.2.1-192...

  • Page 270

    5. Cli management in snm-24mgb 263 airlive snmp-24mgb user’s manual : a specific or range management policy entry(s) e.G. Delete 2,3,8-12 possible value: : a specific or range management policy entry(s) example: snmp-24mgb(policy)# add name rule2 ip 192.168.4.23-192.168.4.33 port 6-8 type s,t action...

  • Page 271

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 264 none example: snmp-24mgb(policy)# show 1) name : rule1 ip range : 192.168.4.5-192.168.4.22 action : deny access type : http telent snmp port : 2 3 4 5 2) name : rule2 ip range : 192.168.4.23-192.168.4.33 action : deny access type...

  • Page 272

    5. Cli management in snm-24mgb 265 airlive snmp-24mgb user’s manual argument : syntax : 1,5-7, available from 1 to 24 : set port description, max 47 characters possible value: : 1 to 24 : max 47 characters example: snmp-24mgb(port)# set description 3-8 salesdepartment snmp-24mgb(port)# show config s...

  • Page 273

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 266 snmp-24mgb(port)# show config speed/ flow maximum excessive port duplex control frame collision description a list of previously run command set priority ---- --------- -------- ------- --------- --------------------------------d...

  • Page 274

    5. Cli management in snm-24mgb 267 airlive snmp-24mgb user’s manual 6 auto enabled 9600 restart salesdepartment 7 auto enabled 9600 restart salesdepartment 8 auto enabled 9600 restart salesdepartment 9 auto enabled 9600 restart 10 auto enabled 9600 restart 11 auto disabled 9600 discard 12 auto disab...

  • Page 275

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 268 10 auto enabled 9600 restart 11 auto disabled 9600 discard set speed syntax : set speed description : to set port capability. Argument : :syntax 1,5-7, available from 1 to 24 : auto: set auto-negotiation mode 10half: set speed/du...

  • Page 276

    5. Cli management in snm-24mgb 269 airlive snmp-24mgb user’s manual 7 up 1g/full disabled disabled 8 down down disabled disabled 9 down down disabled disabled set powersaving syntax : set set powersaving description : to set power saving. Argument : port: 1,5-7, available from 1 to 8 0: disable, 1: ...

  • Page 277

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 270 snmp-24mgb(port)# show config speed/ flow maximum excessive port duplex control frame collision description ---- --------- -------- ------- --------- -------------------------------- 1 auto disabled 9600 discard 2 1g/full disable...

  • Page 278

    5. Cli management in snm-24mgb 271 airlive snmp-24mgb user’s manual receive size counters transmit size counters ------------------------------- ------------------------------------ rx 64 bytes 7381 tx 64 bytes 4351 rx 65-127 bytes 291 tx 65-127 bytes 2342 rx 128-255 bytes 118 tx 128-255 bytes 605 r...

  • Page 279

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 272 --------------------------------------------------------------------- connector type : sfp - unknown or unspecified fiber type : reserved tx central wavelength : 0 baud rate : 1g vendor oui : 00:00:00 vendor name : fiberxon inc. ...

  • Page 280

    5. Cli management in snm-24mgb 273 airlive snmp-24mgb user’s manual show simple-counter syntax : show simple-counter description : to display the summary counting of each port’s traffic. Argument : none. Possible value: none. Example: snmp-24mgb(port)# show simple-counter set max-frame set per-port ...

  • Page 281

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 274 syntax : show status description : to display the port’s current status. Argument : none. Possible value: none. Example: snmp-24mgb(port)# show status speed/1g/full disable port link duplex rx pause tx pause description 3 auto di...

  • Page 282

    5. Cli management in snm-24mgb 275 airlive snmp-24mgb user’s manual snmp-24mgb(port)# show powersaving port power saving ---- ------------ 1 disabled 2 disabled 3 disabled 4 disabled 5 disabled 6 disabled 7 disabled 8 disabled snmp-24mgb(port)# z qos > set class syntax : set class description : to s...

  • Page 284

    5. Cli management in snm-24mgb 277 airlive snmp-24mgb user’s manual 5 low 1 0 strict priority 1 / 2 / 4 / 8 6 low 1 0 strict priority 1 / 2 / 4 / 8 7 low 1 0 strict priority 1 / 2 / 4 / 8 8 low 1 0 strict priority 1 / 2 / 4 / 8 9 low 1 0 strict priority 1 / 2 / 4 / 8 10 low 1 0 strict priority 1 / 2...

  • Page 285

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 278 10 low 1 0 strict priority 1 / 2 / 4 / 8 > set syntax : set description : to add the qce entry in the specific qcl argument : : dscp field, syntax 1,5-7, available from 0 to 63 : tos priority , available from 1 to 8 : tag priorit...

  • Page 286

    5. Cli management in snm-24mgb 279 airlive snmp-24mgb user’s manual move syntax : move description : to move up the specific qce entry in the specific qcl argument : : the qcl number, available from 1 to 24. : the original qce number, available from 1 to 12. : the new qce number, available from 1 to...

  • Page 287

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 280 > set syntax : set description : to set rate limit configuration argument : : 1,5-7, available from 1 to 24 : 1 means enable and 0 means disable : allowed values are 500kbps-1gkps : 'k' means kbps and 'm' means mbps : 1 means ena...

  • Page 288

    5. Cli management in snm-24mgb 281 airlive snmp-24mgb user’s manual 7 500 kbps 500 kbps 8 500 kbps 500 kbps 9 500 kbps 500 kbps 10 500 kbps 500 kbps > set broadcast syntax : set broadcast description : to set broadcast storm control configuration argument : : 1 means enable and 0 means disable : 1, ...

  • Page 289

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 282 syntax : set multicast description : to set multicast storm control configuration argument : : 1 means enable and 0 means disable : 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1k, 2k, 4k, 8k, 16k, 32k, 64k, 128k , 256k, 512k possible ...

  • Page 290

    5. Cli management in snm-24mgb 283 airlive snmp-24mgb user’s manual possible value: : 1 means enable and 0 means disable : 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1k, 2k, 4k, 8k, 16k, 32k, 64k, 128k , 256k, 512k example: snmp-24mgb(qos-storm)# set unicast 1 128 snmp-24mgb(qos-storm)# show frame type ...

  • Page 291

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 284 z reboot reboot syntax: reboot description: to reboot the system. Argument: none. Possible value: none. Example: snmp-24mgb# reboot z snmp disable syntax : disable set-ability disable snmp description : the disable here is used f...

  • Page 292

    5. Cli management in snm-24mgb 285 airlive snmp-24mgb user’s manual enable syntax : enable set-ability enable snmp description : the enable here is used for the activation snmp or set-community. Argument : none. Possible value: none. Example: snmp-24mgb(snmp)# enable snmp snmp-24mgb(snmp)# enable se...

  • Page 293

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 286 show syntax : show description : the show here is to display the configuration of snmp. Argument : none. Possible value: none. Example: snmp-24mgb(snmp)# show snmp : enable get community: public set community: private [enable] tr...

  • Page 294

    5. Cli management in snm-24mgb 287 airlive snmp-24mgb user’s manual example: snmp-24mgb(stp)# mcheck 1-8 disable syntax : disable description : to disable the stp function. Argument : none. Possible value: none. Example: snmp-24mgb(stp)# disable enable syntax : enable description : to enable the stp...

  • Page 295

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 288 syntax : set config description : to set up the parameters of stp. Argument : :priority must be a multiple of 4096, available from 0 to 61440. : available from 1 to 10. : available from 6 to 40. : available from 4 to 30. Note: 2*...

  • Page 296

    5. Cli management in snm-24mgb 289 airlive snmp-24mgb user’s manual :1 to 24 : 0, 1-200000000 : 0 to 240 : yes / no : auto / true / false example: snmp-24mgb(stp)# set port 1-16 0 128 yes auto set version syntax : set version description : to set up the version of stp. Argument : :stp / rstp possibl...

  • Page 297

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 290 example: snmp-24mgb(stp)# show config stp state configuration : spanning tree protocol : enabled bridge priority (0-61440) : 61440 hello time (1-10 sec) : 2 max. Age (6-40 sec) : 20 forward delay (4-30 sec) : 15 force version : r...

  • Page 298

    5. Cli management in snm-24mgb 291 airlive snmp-24mgb user’s manual 9 discarding 2000000 128 no auto 10 discarding 2000000 128 no auto 11 discarding 2000000 128 no auto 12 discarding 2000000 128 no auto 13 discarding 2000000 128 no auto 14 discarding 2000000 128 no auto 15 discarding 2000000 128 no ...

  • Page 299

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 292 bridge id : 00:40:c7:d8:09:1d bridge priority : 61440 designated root : 00:40:c7:d8:09:1d designated priority : 61440 root port : 0 root path cost : 0 current max. Age(sec) : 20 current forward delay(sec) : 15 hello time(sec) : 2...

  • Page 300

    5. Cli management in snm-24mgb 293 airlive snmp-24mgb user’s manual : string length up to 40 characters. Possible value: : a, b, c, d, ... ,z and 1, 2, 3, …. Etc. Example: snmp-24mgb (system)# set device-name cr-2600 set location syntax : set location description : to set the location description of...

  • Page 301

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 294 ---- --------------------------- ------------------------------------ show syntax : show description : to display the trap log. Argument : none. Possible value: none. Example: snmp-24mgb(tftp)# show 2 mon mar 17 15:18:38 2008gvrp...

  • Page 302

    5. Cli management in snm-24mgb 295 airlive snmp-24mgb user’s manual snmp-24mgb(system)# show model name : snmp-24mgb system description : 24+8 combo pure gigabit snmp managed switch location : contact : device name : snmp-24mgb system up time : 0 days 0 hours 4 mins 14 secs current time : tue jan 17...

  • Page 303

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 296 mm : (01-12) dd : (01-31) hh : (00-23) mm : (01-12) dd : (01-31) hh : (00-23) example: snmp-24mgb(time)# set daylightsaving 3 10/12/01 11/12/01 save successfully set manual syntax: set manual description: to set up the current ti...

  • Page 304

    5. Cli management in snm-24mgb 297 airlive snmp-24mgb user’s manual : -12,-11…,0,1…,13 example: snmp-24mgb(time)# set ntp clock.Via.Net 8 synchronizing...(1) synchronization success show syntax: show description: to show the time configuration, including “current time”, “ntp server”,” timezone”, ” d...

  • Page 305

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 298 argument : : port range, syntax 1,5-7, available from 1 to 24 possible value: : 1 to 24 example: snmp-24mgb(trunk)# del trunk 1 set priority syntax : set priority description : to set up the lacp system priority. Argument : : ava...

  • Page 306

    5. Cli management in snm-24mgb 299 airlive snmp-24mgb user’s manual : static / lacp : 1-8. : active / passive example: snmp-24mgb(trunk)# set trunk 1-4 lacp 1 active show aggtr-view syntax : show aggtr-view description : to display the aggregator list. Argument : none. Possible value: none. Example:...

  • Page 307

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 300 : 1 to 24 example: snmp-24mgb(trunk)# show lacp-detail 2 aggregator 2 information: actor partner --------------------------------- --------------------------------- system priority mac address system priority mac address --------...

  • Page 308

    5. Cli management in snm-24mgb 301 airlive snmp-24mgb user’s manual possible value: none. Example: snmp-24mgb(trunk)# show status trunk port setting trunk port status ------------------------------------- ---------------------- port method group active lacp aggtregator status ====== ======== =======...

  • Page 309

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 302 : port-vlan name example: snmp-24mgb(vlan)# del port-group vlan-2 del tag-group syntax: del tag-group description: to delete the tag-based vlan group. Argument: : which vlan group you want to delete, available from 1 to 4094 poss...

  • Page 310

    5. Cli management in snm-24mgb 303 airlive snmp-24mgb user’s manual disable sym-vlan syntax: disable sym-vlan description: to drop frames from the non-member port. Argument: : which port(s) you want to set, syntax 1,5-7, available from 1 to 24 possible value: : 1 to 24 example: snmp-24mgb(vlan)# dis...

  • Page 311

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 304 to drop frames from the non-member port. Argument: : which port(s) you want to set, syntax 1,5-7, available from 1 to 24 possible value: : 1 to 24 example: snmp-24mgb(vlan)# enable sym-vlan 5-10 set mode syntax: set mode [up-link...

  • Page 312

    5. Cli management in snm-24mgb 305 airlive snmp-24mgb user’s manual argument: : 1,5-7, available from 1 to 24 0: disable 1: service provider port 2: customer port possible value: : 1 to 24 example: snmp-24mgb(vlan)#set double-tag 3 1 snmp-24mgb(vlan)# set port-group syntax: set port-group descriptio...

  • Page 313

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 306 :which port(s) you want to set, syntax 1,5-7, available from 1 to 24 : do not tag frames : tag all frames : tag all frames except a specific vid : untag-vid for hybrid port possible value: : 1 to 24 : 1 to 4094 example: snmp-24mg...

  • Page 314

    5. Cli management in snm-24mgb 307 airlive snmp-24mgb user’s manual to add or edit the tag-based vlan group. Argument: : vlan id, range from 1 to 4094 : tag-vlan name : vlan group members, syntax 1,5-7, available from 1 to 24 : sym/asym vlan setting. 1: symmetric vlan, 0: asymmetric vlan possible va...

  • Page 315

    5. Cli management in snm-24mgb airlive snmp-24mgb v2 user’s manual 308 vlan id : 2 sym-vlan : disable member : 2 3 4 5 6 13 14 15 show port syntax: show port description: to display pvid, ingress/egress rule. Argument: none. Possible value: none. Example: snmp-24mgb(vlan)# show pvid port pvid rule1 ...

  • Page 316: 6.1 Incorrect Connections

    6. Troubleshooting 309 airlive snmp-24mgb user’s manual this section is intended to help you solve the most common problems on the snmp-24mgb. 6.1 incorrect connections the switch port can auto detect straight or crossover cable when you link switch with other ethernet device. For the rj-45 connecto...

  • Page 317: 6.3 Cabling

    6. Troubleshooting airlive snmp-24mgb v2 user’s manual 310 6.2 diagnosing led indicators the snmp-24mgb can be easily monitored through panel indicators to assist in identifying problems, which describes common problems you may encounter and where you can find possible solutions. Please refer to cha...

  • Page 318: Specifications

    7. Specifications 311 airlive snmp-24mgb user’s manual this section provides the specifications of snmp-24mgb, and the following table lists these specifications. Standard z ieee802.3 10base-t z ieee802.3u 100base-tx/100base-fx z ieee802.3z gigabit sx/lx z ieee802.3ab gigabit 1000t z ieee802.3x flow...

  • Page 319

    7. Specifications airlive snmp-24mgb v2 user’s manual 312 z rfc standard snmp agent : mib-2 (rfc 1213) bridge mib (rfc 1493) rmon mib (rfc 1757)-statistics ethernet-like mib (rfc 1643) enterprise mib z snmp trap trap station up to 6. Z tftp and console firmware upgradeable z port trunk support ieee8...

  • Page 320

    7. Specifications 313 airlive snmp-24mgb user’s manual z supports port mirroring z supports flooded unicast / multicast / broadcast storm control z supports ingress and egress per port bandwidth control, per level 500 kbps ~ 1000000 kbps or 1 mbps ~ 1000 mbps z supports 802.1x access control for por...

  • Page 321: Network Glossary

    8. Network glossary airlive snmp-24mgb v2 user’s manual 314 the network glossary contains explanation or information about common terms used in wireless networking products. Some of information in this glossary might be outdated, please use with caution. 100base-fx the ieee standard defines how to t...

  • Page 322

    8. Network glossary 315 airlive snmp-24mgb user’s manual speed, and is backward compatible with 10/100base-tx standard. 802.1d stp spanning tree protocol. It is an algorithm to prevent network from loop topology. Spanning tree allows a network design to include spare (redundant) links to provide aut...

  • Page 323

    8. Network glossary airlive snmp-24mgb v2 user’s manual 316 firmware the program that runs inside embedded device such as ap or switch. Many network devices are firmware upgradeable through web interface or utility program. Ftp file transfer protocol. A standard protocol for sending files between co...

  • Page 324

    8. Network glossary 317 airlive snmp-24mgb user’s manual media access control. Mac address provides layer-2 identification for network devices. Each ethernet device has its own unique address. The first 6 digits are unique for each device manufacturers. When a network device has mac access control f...

  • Page 325

    8. Network glossary airlive snmp-24mgb v2 user’s manual 318 an address code mask that determines the size of the network. An ip subnet are determined by performing a bit-wise and operation between the ip address and the subnet mask. By changing the subnet mask, you can change the scope and size of a...