1. DL manuals
  2. AirLive
  3. Switch
  4. SNMP-FSH2602MG
  5. User Manual

AirLive SNMP-FSH2602MG User Manual

Manual is about: 26+2-port SNMP/Web Management Switch

Summary of SNMP-FSH2602MG

  • Page 1

    Airlive snmp-fsh2602mg user’s manual 1 snmp-fsh2602mg 26+2-port snmp/web management switch user’s manual.

  • Page 2: Declaration of Conformity

    Declaration of conformity we, manufacturer/importer declare that the product 26+2-port snmp/web management switch snmp-fsh2602mg is in conformity with in accordance with 89/336 eec-emc directive and 1999/5 ec-r & tte directive clause description limits and methods of measurement of radio disturbance...

  • Page 3

    Snmp-fsh2602mg ce declaration statement country declaration country declaration cs Česky [czech] ovislink corp. Tímto prohlašuje, že tento snmp- fsh2602mg je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/es. Lt lietuvių [lithuanian] Šiuo ovislink corp. Deklaruoj...

  • Page 4: About This User’S Manual

    Trademarks all rights reserved. Airlive logo is a registered trademarks of ovislink corp., taiwan. Other product names and company names are trademarks or registered trademarks of their respective owners. Fcc warning this equipment has been tested and found to comply with the requirements for a clas...

  • Page 5

    Airlive snmp-fsh2602mg user’s manual i table of contents 1 product overview ..................................................................................... 1 introduction ....................................................................................................................... 1 g...

  • Page 6

    Airlive snmp-fsh2602mg user’s manual ii comprehensive leds ..................................................................................................... 12 system leds .................................................................................................................... 12 fan1...

  • Page 7

    Airlive snmp-fsh2602mg user’s manual iii max bridge transit delay bound control ............................................................ 26 broadcast storm filter ...................................................................................... 26 priority queue service settings ..............

  • Page 8

    Airlive snmp-fsh2602mg user’s manual iv per port configuration .................................................................................................. 49 misc configuration ....................................................................................................... 49 ping .......

  • Page 9

    Airlive snmp-fsh2602mg user’s manual v misc configuration ......................................................................................................... 72 mac age interval ........................................................................................................ 72 broadcas...

  • Page 10: Figures

    Airlive snmp-fsh2602mg user’s manual vi application examples ................................................................................................... 110 benefit of vans ......................................................................................................... 111 trunking ...

  • Page 11

    Airlive snmp-fsh2602mg user’s manual vii figure 5-1 manual ip setting ........................................................................................ 55 figure 5-2 remote management through direct internet ............................................ 56 figure 5-3 remote management through ...

  • Page 12: Tables

    Airlive snmp-fsh2602mg user’s manual viii tables table 2-1 module specification table ........................................................................... 7 table 2-2 cabling type for 10/100base-tx and 1000base-t .................................... 10 table 3-1 led table .......................

  • Page 13: Product Overview

    Airlive snmp-fsh2602mg user’s manual 1 1 product overview introduction the snmp-fsh2602mg features 24 fast ethernet ports with auto mdi/mdi-x function to eliminate the need for cross-over cables. Snmp-2602mg have 2 1000base-t/-sx/-lx, mini-gbic ports onboard with auto-detection .All this power is co...

  • Page 14

    Airlive snmp-fsh2602mg user’s manual 2 quick setup this section provides the essential information for experienced users to operate the switch immediately. For detailed installation instruction, please see chapter 2 for more information. Power-on the switch the snmp-fsh2602mg has a built-in power su...

  • Page 15

    Airlive snmp-fsh2602mg user’s manual 3 “192.168.223.100 in web browser or telnet program to manage the switch. If users can’t find the switch at the default ip address, please connect the switch to the console port. Use the console port management to change the switch’s ip configuration. Console por...

  • Page 16: Installation of The Switch

    Airlive snmp-fsh2602mg user’s manual 4 2 installation of the switch this chapter provides the detailed instructions for installation of the switch. For concise installation instruction, the previous chapter’s “quick setup” section provides all the important information including ip address, password...

  • Page 17

    Airlive snmp-fsh2602mg user’s manual 5 unpack the package before you begin the installation of snmp-fsh2602mg, make sure that you have all the necessary accessories that come with your package. Follow the steps below to unpack your package contents: 1. Clear out an adequate space to unpack the packa...

  • Page 18

    Airlive snmp-fsh2602mg user’s manual 6 hardware overview front panel the front panel is where you can find the twenty-four 10/100mbps station ports, the module slot, console port, and the led indicators. For the technical specifications of the ports, please refer to appendix a, product specification...

  • Page 19

    Airlive snmp-fsh2602mg user’s manual 7 cooling fans : the snmp-fsh2602mg is equipped with 2 cooling fans located on the sides of the switch. When facing front, the left cooling fan is designated as fan 1 and the right cooling fan is designated as fan2. When a fan has failed, the fan status led on th...

  • Page 20

    Airlive snmp-fsh2602mg user’s manual 8 switch has to comply with the following requirements: • the surface where you want to mount the switch must be able to sustain at least 2.5kg. • do not place heavy objects (more than 3kg) on top of the switch. • the location must preferably be free from excessi...

  • Page 21

    Airlive snmp-fsh2602mg user’s manual 9 fig. 2-5 attaching the switch to a 19-inch rack desktop installation snmp-fsh2602mg has four rubber pads attached on each corner of its underside. These pads serve as cushioning against vibration and prevent the switch from sliding off its position. They also a...

  • Page 22

    Airlive snmp-fsh2602mg user’s manual 10 the following table summarizes the cable requirement for 10/100/1000base-tx connection: 10base-t 100 ohm category 3, 4, 5 utp/stp cable 100base-tx 100 ohm category 5 utp/stp cable 1000base-t 100 ohm category 5 utp/stp cable or better (cat 5e recommended) auto ...

  • Page 23

    Airlive snmp-fsh2602mg user’s manual 11 connecting to power snmp-fsh2602mg features a universal auto-select power supply unit, which allows a power connection to a wide range of input voltages from 90 to 260v ac @ 50 ~ 60hz. To establish its power connection, simply plug the female end of the power ...

  • Page 24: Led Indicators

    Airlive snmp-fsh2602mg user’s manual 12 3 led indicators before connecting any network device to snmp-fsh2602mg, you should take a few minutes to look over this chapter and get familiar with the front panel led indicators of your switch. Comprehensive leds the front-panel led indicators of snmp-fsh2...

  • Page 25

    Airlive snmp-fsh2602mg user’s manual 13 station port leds for port 1 ~ 24 the snmp-fsh2602mg is equipped with 2 leds on the sides of each rj-45 station port. This design allows users to view the status of each port quickly. The left led indicates the link/action status. The right led indicates wheth...

  • Page 26: Web Management

    Airlive snmp-fsh2602mg user’s manual 14 4 web management the snmp-fsh2602mg supports in-band management through web browser. In this session, you will learn how to access the switch’s powerful management functions through the web browser. You will also learn how to manage the switch remotely through...

  • Page 27

    Airlive snmp-fsh2602mg user’s manual 15 configure your computer’s ip before accessing the switch through web browse, please follow the instruction below to configure your computer’s ip to the same subnet as the switch. If your switch’s ip has not been changed, it should have the following factory de...

  • Page 28

    Airlive snmp-fsh2602mg user’s manual 16 click on “use the following ip address” button and enter the computer’s address manually. This ip address must be on the same subnet as the switch but different from the switch’s ip. Please make sure the ip is not used by other network device. If the switch’s ...

  • Page 29

    Airlive snmp-fsh2602mg user’s manual 17 cable modem : if your cable service provider uses dhcp for ip assignment, please turn on the dhcp function under ip configuration. Make sure there is no dhcp server in the network. Then the cable provider will assign the switch with an ip and gateway. Go to th...

  • Page 30

    Airlive snmp-fsh2602mg user’s manual 18 step 2 : enter the switch’s ip address in the address field and press enter. Step 3 : when prompt for user’s name and password, enter the following information: user’s name: admin password: 123 you should see the following welcome screen after the process is c...

  • Page 31

    Airlive snmp-fsh2602mg user’s manual 19 port status all port status click on “port status” of the left menu bar will bring up the general status for all the ports and modules. Figure 4-3 all port status state: display port statuses: disable or enable. “unlink” will be treated as “off ”. Link status:...

  • Page 32

    Airlive snmp-fsh2602mg user’s manual 20 atual: display the negotiation result. Single port status user can also click the any port directly on the front panel of home page to get single port status which is shown below. Figure 4-4 single port status the state shows whether the port has been installe...

  • Page 33

    Airlive snmp-fsh2602mg user’s manual 21 figure 4-5 port statistics txgoodpkt – number of good packets sent txbadpkt – number of bad packets sent rxgoodpkt – number of good packets received rxbadpkt – number of bad packets received txabort – number of aborted packets collison - number of collisions d...

  • Page 34

    Airlive snmp-fsh2602mg user’s manual 22.

  • Page 35

    Airlive snmp-fsh2602mg user’s manual 23 show mac table the following information provides a table of the current mac addresses that the switch has learned. Press “prev” or “next” button will browse previous 50 or next 50 items. The “top” button will re-list the table from the first mac. A sorting fu...

  • Page 36

    Airlive snmp-fsh2602mg user’s manual 24 administrator there are many management functions can be set or performed if you click the administrator on home page, including: ip and management mode switch settings console port information port controls trunking filter database vlan configuration rapid sp...

  • Page 37

    Airlive snmp-fsh2602mg user’s manual 25 figure 4-6 ip configuration note3: we do not recommend turning on the dhcp client because the dhcp server assign the ip randomly. Therefore, users will need to use the console port to find the ip address after assignment. The dhcp client should be used only wh...

  • Page 38

    Airlive snmp-fsh2602mg user’s manual 26 mac address age-out time type the number of seconds that an inactive mac address remains in the switch's address table. The valid range is 300~765 seconds. Default is 300 seconds. Max bridge transit delay bound control limit the packets queuing time in switch....

  • Page 39

    Airlive snmp-fsh2602mg user’s manual 27 802.1p priority first come first service: the sequence of packets sent is depending on arrive orders. All high before low: the high priority packets sent before low priority packets. Wrr: weighted round robin. Select the preference given to packets in the swit...

  • Page 40

    Airlive snmp-fsh2602mg user’s manual 28 console port information (administrator menu) console is a standard uart interface to communicate with serial port. User can use windows hyperterminal program to link the switch. Connect to -> configure: bits per seconds: 57600 data bits: 8 parity: none stop b...

  • Page 41

    Airlive snmp-fsh2602mg user’s manual 29 state: user can disable or enable this port. Auto negotiation: user can set auto negotiation mode is auto, nway (specify the speed/duplex on this port and enable auto-negotiation), force of per port. Speed: user can set 100mbps or 10mbps speed on port1~port24;...

  • Page 42

    Airlive snmp-fsh2602mg user’s manual 30 type of control is called “bandwidth management.” separate bandwidth management for incoming and outgoing traffic is important because broadband connection such as adsl has different upstream and downstream speed. Application hotel : for hotels that provide in...

  • Page 43

    Airlive snmp-fsh2602mg user’s manual 31 how to setup step 1: under the web configuration, choose administrator->port control s t e p 2 : p l e a s e s e l ect the port where you want to control the rate step 3 : under the field “rate control”, enter values in the ingr(ingress) and egr(egress) field ...

  • Page 44

    Airlive snmp-fsh2602mg user’s manual 32 aggregator setting figure 4-12 trunking system priority: a value used to identify the active lacp. The switch with the lowest value has the highest priority and is selected as the active lacp. Group id: there are seven trunk groups to provided configure. Choos...

  • Page 45

    Airlive snmp-fsh2602mg user’s manual 33 1 11 . .. If following screen is shown, it indicates no group is active. Lacp is not working. 2 22 . .. If the following screen is shown, this indicates static trunking groups has been made. 3 33 . .. If the following page is shown, it indicates lacp trunking ...

  • Page 46

    Airlive snmp-fsh2602mg user’s manual 34 figure 4-13 trunking state activity active (select): the port automatically sends lacp protocol packets. N/a (no select): the port does not automatically sends lacp protocol packets, and responds only if it receives lacp protocol packets from the opposite devi...

  • Page 47

    Airlive snmp-fsh2602mg user’s manual 35 figure 4-14 igmp snooping the internet group management protocol (igmp) is an internal protocol of the internet protocol (ip) suite. Ip manages multicast traffic by using switches, routers, and hosts that support igmp. Enabling igmp allows the ports to detect ...

  • Page 48

    Airlive snmp-fsh2602mg user’s manual 36 figure 4-15 static mac address at the main menu, click administrator filter database static mac address. In the mac address box, enter the mac address to and from which the port should permanently forward traffic, regardless of the device’s network activity. I...

  • Page 49

    Airlive snmp-fsh2602mg user’s manual 37 figure 4-16 mac filtering in the mac address box, enter the mac address that wants to filter. If tag-based (802.1q) vlan are set up on the switch, in the vlan id box, type the vid to associate with the mac address. Click the add. Choose the mac address that yo...

  • Page 50

    Airlive snmp-fsh2602mg user’s manual 38 port-based vlan in port-based vlan, users group member ports into different vlan groups. Packets can only be broadcast among only members of the same vlan group. However, overlapping ports between different vlan groups can be used for device sharing purpose. I...

  • Page 51

    Airlive snmp-fsh2602mg user’s manual 39 configuring port based vlan figre 4-17 configure port-based vlan click add to create a new vlan group. Enter the vlan name, group id and select the members for the new vlan. Click apply. If there are many groups that over the limit of one page, you can click t...

  • Page 52

    Airlive snmp-fsh2602mg user’s manual 40 configuring 802.1q and 802.1v vlan this page, user can create tag-based vlan, and enable or disable gvrp protocol. There are 4093 vlan groups to provide configure. Enable 802.1q vlan, the all ports on the switch belong to default vlan, vid is 1. The default vl...

  • Page 53

    Airlive snmp-fsh2602mg user’s manual 41 type a name for the new vlan. Type a vid (between 2 to 4094). The default is 1. Choose the protocol type. We support 802.1v with the implementation of port-and-protocol-based vlan classification. User can combine the field “protocol vlan” and the field of the ...

  • Page 54

    Airlive snmp-fsh2602mg user’s manual 42 port vid (pvid) set the port vlan id that will be assigned to untagged traffic on a given port. This feature is useful for accommodating devices that you want to participate in the vlan but that don’t support tagging. Each port of snmp-fsh2602mg allows user to...

  • Page 55

    Airlive snmp-fsh2602mg user’s manual 43 the spanning tree status about the switch is shown in the following screen. Setting spanning tree figure 4-19 set spanning tree please change the parameter according to the parameter table description below : parameter description priority you can change prior...

  • Page 56

    Airlive snmp-fsh2602mg user’s manual 44 a number 1 through 10. Forward delay time you can change forward delay time, the number of seconds a port waits before changing from its spanning-tree protocol learning and listening states to the forwarding state. Enter a number 4 through 30. Table 4-2 spanni...

  • Page 57

    Airlive snmp-fsh2602mg user’s manual 45 figre 4-21 port mirror roving analysis mode: press space key to set sniffer mode: disable \rx \tx \both. Analysis port: it means that this port can be used to see all monitors port traffic. You can connect analysis port to lan analyzer or netxray. Monitored po...

  • Page 58

    Airlive snmp-fsh2602mg user’s manual 46 community strings serve as passwords and can be entered as one of the following: ro: read only. Enables requests accompanied by this string to display mib-object information. Rw : read write. Enables requests accompanied by this string to display mib-object in...

  • Page 59

    Airlive snmp-fsh2602mg user’s manual 47 user name: type the new user name. Password: type the new password. Reconfirm password: retype the new password. Click apply. Introduction to 802.1x authentication protocol function : the 802.1x protocol allow authentication and authorization information to be...

  • Page 60

    Airlive snmp-fsh2602mg user’s manual 48 authenticator : the authenticator is the device between the client and the radius server. It is typically an ap or switch. When a client needs to access certain service, the authenticator will forward the request to the authentication server and wait for the a...

  • Page 61

    Airlive snmp-fsh2602mg user’s manual 49 radius server ip address : the ip address of the authentication server. Server port : the udp port number used by the authentication server to authenticate. Accounting port : the udp port number used by the authentication server to retrieve accounting informat...

  • Page 62

    Airlive snmp-fsh2602mg user’s manual 50 quiet period ： used to define periods of time during which it will not attempt to acquire a supplicant (default time is 60 seconds). Tx period ： used to determine when an eapol pdu is to be transmitted (default value is 30 seconds). Supplicant timeout ： used t...

  • Page 63

    Airlive snmp-fsh2602mg user’s manual 51 this page will display the result of the pinging ip. It continues updating the “reply counts” when the ping packets are sending. User can interrupt the progress by clicking “stop” button. If the reply counts remain zero after webpage reload stops, it could mea...

  • Page 64

    Airlive snmp-fsh2602mg user’s manual 52 configuration backup tftp restore configuration use this page to set ftp server address. You can restore eeprom value from here, but you must put back image in ftp server, switch will download back flash image. Tftp backup configuration use this page to set tf...

  • Page 65

    Airlive snmp-fsh2602mg user’s manual 53 reset system reset switch to the default configuration reboot reboot the switch in software reset event logging a history log is provided here to give a track about events that the switch had happened. There are 100 loggings for maximum capacity of this switch...

  • Page 66: Terminal Management

    Airlive snmp-fsh2602mg user’s manual 54 5 terminal management the snmp-fsh2602mg supports terminal management through telnet or console port. Console port management allows out-of-band management and serves as a backup when web/telnet management fails. For station that does not have internet explore...

  • Page 67

    Airlive snmp-fsh2602mg user’s manual 55 your computer’s ip to the same subnet as the switch. If your switch’s ip has not been changed, it should have the following factory default value: the switch’s default ip ip address: 192.168.223.100 subnet mask: 255.255.248.0 gateway: 192.168.223.254 now if yo...

  • Page 68

    Airlive snmp-fsh2602mg user’s manual 56 of factory’s default value. We recommend enter the following for computer’s ip: ip address: 192.168.223.101 subnet mask: 255.255.248.0 gateway: 192.168.223.254 click “okay” after finish entering the ip. *note: an alternative method is to change the switch’s ip...

  • Page 69

    Airlive snmp-fsh2602mg user’s manual 57 network. Then the cable provider will assign the switch with a ip and gateway. Go to the console port management to find out what ip has been assigned to the switch. When the configuration is finished, the remote pc can access the switch by typing the switch’s...

  • Page 70

    Airlive snmp-fsh2602mg user’s manual 58 you should see the following welcome screen after the process is completed: console port management snmp-fsh2602mg offers you a secure way to configure your switch through a rs-232 cable that connects its console port and the host pc. Using windows hypertermin...

  • Page 71

    Airlive snmp-fsh2602mg user’s manual 59 fig. 5-5 console port fig. 6-3 rs-232 cable note: after you have established a rs-232 cable connection between snmp-fsh2602mg and your host pc, if your snmp-fsh2602mg or the host pc is not powered on, you should power them up before you can configure smart con...

  • Page 72

    Airlive snmp-fsh2602mg user’s manual 60 step 3: ether any name you would like to have for this connection (in this example, we use snmp-fsh2602mg as name for the connection) and choose an icon. Click ok. Step 4: the connect to dialog box appear. Since the hyperterminal connection is made through con...

  • Page 73

    Airlive snmp-fsh2602mg user’s manual 61 step 5: the com port properties dialog box (in this case, com1 properties dialog box) appears. Configure the various port settings such as followings: bits per second: 57600 data bits: 8 parity: none stop bits: 1 flow control: none click ok. Step 6: press when...

  • Page 74

    Airlive snmp-fsh2602mg user’s manual 62 step 7: when prompted for user’s name and password. Enter “ admin ” as username and “ 123 ” as password. After the host pc has successfully connected to snmp-fsh2602mg, you will see the switch setup main menu appears. Main menu once getting into the terminal m...

  • Page 75

    Airlive snmp-fsh2602mg user’s manual 63 switch configuration you can press the key of tab or backspace to choose item, and press enter key to select item the action menu line as follow provided in later configure page. Actions-> : exit the page of port configuration and return to previous menu. : co...

  • Page 76

    Airlive snmp-fsh2602mg user’s manual 64 port configuration this page can change every port status. Press space key to change configures of per item. Inrate (100k/unit): user can set input rate control, per unit is 100k. The valid range is 0~1000. 0: disable rate control. 1~1000: valid rate value. Ou...

  • Page 77

    Airlive snmp-fsh2602mg user’s manual 65 trunk configuration this page can create max seven trunk groups. User can arbitrarily select up to four ports from port 1~port 26 to build a trunking group. Actions-> select on actions menu press space key to configure the member port of trunk group. Besides, ...

  • Page 78

    Airlive snmp-fsh2602mg user’s manual 66 vlan configuration vlan configure this page can set vlan mode to port-based vlan or 802.1q vlan or disable vlan function. Note: change the vlan mode for every time, user have to restart the switch for valid value. If set 802.1q vlan, you can set pvid, ingress ...

  • Page 79

    Airlive snmp-fsh2602mg user’s manual 67 actions-> pvid (port vid: 1~255): type the pvid. Nonmember drop: it matches that ingress filtering rule 1 on web. Forwarding only packets with vid matching this port’s configured vid. Press space key to choose “forward” or “drop” the frame that vid not matchin...

  • Page 80

    Airlive snmp-fsh2602mg user’s manual 68 note: if the trunk groups exist, you can see it (ex: trk1, trk2…) after port26, and you can configure it is the member of the vlan or not. Create 802.1q vlan create an 802.1q vlan and add tagged /untagged member ports to it. Select . Vlan name: type a name for...

  • Page 81

    Airlive snmp-fsh2602mg user’s manual 69 note: if the trunk groups exist, you can see it (ex: trk1, trk2…) after port 26, and you can configure it is the member of the vlan or not. Edit / delete a vlan group in this page, user can edit or delete a vlan group. Press or item. Choose the vlan group that...

  • Page 82

    Airlive snmp-fsh2602mg user’s manual 70 note ： when pressing once will complete deletion on delete mode. The vlan name and vlan id cannot be modified. The default vlan can’t be deleted. Groups sorted mode in this page, user can select vlan groups sorted mode: sorted by name sorted by vid. The edit/d...

  • Page 83

    Airlive snmp-fsh2602mg user’s manual 71 in the edit/delete a vlan group page, the result of sorted by vid..

  • Page 84

    Airlive snmp-fsh2602mg user’s manual 72 misc configuration mac age interval type the number of seconds that an inactive mac address remains in the switch’s address table. The valid range is 300~765 seconds. Default is 300 seconds..

  • Page 85

    Airlive snmp-fsh2602mg user’s manual 73 broadcast storm filtering this page is configuring broadcast storm control. Press to configure the broadcast storm filter mode. Press space key to choose the threshold value. The valid threshold value is 5%, 10%, 15%, 20%, 25% and no. Default is 5%. Max bridge...

  • Page 86

    Airlive snmp-fsh2602mg user’s manual 74 port security a port in security mode will be “locked” without permission of address learning. Only the incoming packets with smac already existing in the address table can be forwarded normally. User can disable the port from learning any new mac addresses, t...

  • Page 87

    Airlive snmp-fsh2602mg user’s manual 75 select to save all configure value. You can press to configure port9 ~ port26, press return to last page. Collision s retry forever collisions retry forever: disable – in half duplex, if happen collision will retry 48 times and then drop frame. Enable – in hal...

  • Page 88

    Airlive snmp-fsh2602mg user’s manual 76 ifg compensation enable or disable the inter-frame gap (ifg) compensation function administration configuration.

  • Page 89

    Airlive snmp-fsh2602mg user’s manual 77 change username use this page; user can change web management user name. Type the new user name, and then press item. Change password use this page; user can change web management login password..

  • Page 90

    Airlive snmp-fsh2602mg user’s manual 78 device information this page is provided to the user to configure the device information. Ip configuration user can configure the ip setting and fill in the new value..

  • Page 91

    Airlive snmp-fsh2602mg user’s manual 79 port mirror configuration the port mirroring is a method for monitor traffic in switched networks. Traffic through ports can be monitored by one specific port. That is traffic goes in or out monitored ports will be duplicated into monitoring port. Actions-> pr...

  • Page 92

    Airlive snmp-fsh2602mg user’s manual 80 priority configuration port static priority this static priority based on port, if you set the port is high priority, income frame from this port always high priority frame..

  • Page 93

    Airlive snmp-fsh2602mg user’s manual 81 802.1p priority configuration there are 0~7-priority level can map to high or low queue. Actions-> select . Press space key to select the priority level mapping to high or low queue. High/low queue service ration h：l: user can select the ratio of high priority...

  • Page 94

    Airlive snmp-fsh2602mg user’s manual 82 static mac address when you add a static mac address, it remains in the switch's address table, regardless of whether the device is physically connected to the switch. This saves the switch from having to re-learn a device's mac address when the disconnected o...

  • Page 95

    Airlive snmp-fsh2602mg user’s manual 83 add static mac address press --> key to add static mac address. Mac address: enter the mac address to and from which the port should permanently forward traffic, regardless of the device’s network activity. Port num: press key to select the port number. Vlan i...

  • Page 96

    Airlive snmp-fsh2602mg user’s manual 84 press ctrl +a to go back action menu line, and then select to save all configure value. Delete static mac address press key. Choose the mac address that you want to delete and then press enter. Pressing once will complete deletion on delete mode..

  • Page 97

    Airlive snmp-fsh2602mg user’s manual 85 filtering mac address mac address filtering allows the switch to drop unwanted traffic. Traffic is filtered based on the destination addresses. In this page user can add /modify /delete filter mac address. Add filter mac address press --> key to add a filter m...

  • Page 98

    Airlive snmp-fsh2602mg user’s manual 86 edit filter mac address press key. Choose the mac address that you want to modify and then press enter. Press key to modify all the items. Press ctrl+a to go back action menu line, and then select to save all configure value..

  • Page 99

    Airlive snmp-fsh2602mg user’s manual 87 delete filter mac address press key to delete a filter mac address. Choose the mac address that you want to delete and then press enter. When pressing once will complete deletion on delete mode. Protocol related configuration.

  • Page 100

    Airlive snmp-fsh2602mg user’s manual 88 stp: spanning tree protocol the spanning-tree protocol (stp) is a standardized method (ieee 802.1d) for avoiding loops in switched networks. When stp enabled, to ensure that only one path at a time is active between any two nodes on the network. Stp enable thi...

  • Page 101

    Airlive snmp-fsh2602mg user’s manual 89 stp system configuration you can view spanning tree information about the root bridge on the left. On the right, user can set new value for stp parameter. Note: all about the parameter description please see the sections web configuration’s explanation of span...

  • Page 102

    Airlive snmp-fsh2602mg user’s manual 90 portstate: display spanning tree status about the switch for per port is forwarding or blocking. Select . Pathcost: specifies the path cost of the port that switch uses to determine which port are the forwarding ports. Priority: this means priority port, you c...

  • Page 103

    Airlive snmp-fsh2602mg user’s manual 91 community strings use this page to add/ edit/ delete snmp community strings. Community name: the name of current strings. Write access: enable the rights is read only or read-write. Restricted: read only, enables requests accompanied by this string to display ...

  • Page 104

    Airlive snmp-fsh2602mg user’s manual 92 add community name press --> key. Community name: type the community name. Write access: press space key to select the right is restricted or unrestricted. Edit community name press key, choose the item that you want to modify and then press enter. Community n...

  • Page 105

    Airlive snmp-fsh2602mg user’s manual 93 delete community name press key. Choose the community name that you want to delete and then press enter. When pressing once will complete deletion on delete mode. Trap managers a trap manager is a management station that receives traps, the system alerts gener...

  • Page 106

    Airlive snmp-fsh2602mg user’s manual 94 add snmp trap manager press --> to add the trap manager. Ip: type the ip address. Community name: type the community name. Press ctrl +a go to actions line, press key to save all configure. Edit trap managers press key, and then choose the item that you want t...

  • Page 107

    Airlive snmp-fsh2602mg user’s manual 95 delete trap manager press key. Choose the trap manager that you want to delete and then press enter. When pressing once will complete deletion on delete mode. Gvrp gvrp (garp [generic attribute registration protocol] vlan registration protocol) gvrp allows aut...

  • Page 108

    Airlive snmp-fsh2602mg user’s manual 96 for example, if the switch is connected to a device with gvrp enabled, you can enable this setting to allow dynamic vlan configuration information to be processed by the switch. If a device sends a gvrp request using the vid of a vlan defined on the switch, th...

  • Page 109

    Airlive snmp-fsh2602mg user’s manual 97 this page you can enable / disable the igmp support . Select . Press space key to choose enabled / disabled. Press ctrl+a go back action menu line. Select to save configure value. Lacp (link aggregation control protocol) this page can configure and view all th...

  • Page 110

    Airlive snmp-fsh2602mg user’s manual 98 note: all ports support lacp dynamic trunking group. If connecting to the device that also supports lacp, the lacp dynamic trunking group will be created automatically. Working port setting this page can set the actually work ports in trunk group. Select . Gro...

  • Page 111

    Airlive snmp-fsh2602mg user’s manual 99 lacp status when you’re setting trunking group, you can see the relational information here. Static trunk group lacp trunk group : exit this page and return to previous menu. : return to previous page to view. : go to the next page to view..

  • Page 112

    Airlive snmp-fsh2602mg user’s manual 100 802.1x protocol this page can configure and view all the 802.1x status. 802.1x enable 1.Select . 2.Press space key to choose enabled / disabled. 3.Press ctrl+a go back action menu line. 4.Select to save configure value..

  • Page 113

    Airlive snmp-fsh2602mg user’s manual 101 802.1x system configuration 1. Press . 2. Radius server ip address: the ip address of the authentication server. 3. Shared key: a key shared between this switch and authentication server. 4. Nas, identifier: a string used to identify this switch. 5. Server po...

  • Page 114

    Airlive snmp-fsh2602mg user’s manual 102 6. Press ctrl+a go back action menu line. 7. Press to save configured value. Note: fu：force the specific port to be unauthorized. Fa：force the specific port to be authorized. Au：the state of the specific port was determined by the outcome of the authenticatio...

  • Page 115

    Airlive snmp-fsh2602mg user’s manual 103 quiet period： used to define periods of time during which it will not attempt to acquire a supplicant (default time is 60 seconds). Tx period： used to determine when an eapol pdu is to be transmitted (default value is 30 seconds). Supplicant timeout： used to ...

  • Page 116

    Airlive snmp-fsh2602mg user’s manual 104 status and counters you can press the key of tab or backspace to choose item, and press enter key to select item. Port status this page display every port status link status: display the port is link or no link. Inrate: display the input rate control (100k/un...

  • Page 117

    Airlive snmp-fsh2602mg user’s manual 105 auto: display the port is link on which nway mode: auto , nway_force , force. Spd/dpx: display the port speed and duplex. Flowctrl: in auto / nway force mode, display the flow control status is enable or not after negotiation. In force mode, display the flow ...

  • Page 118

    Airlive snmp-fsh2602mg user’s manual 106 module 2 information: display the information saved in eeprom of module2. Reboot switch default reset switch to default configuration. Restart reboot the switch in software reset..

  • Page 119

    Airlive snmp-fsh2602mg user’s manual 107 tftp update firmware this page provide user to update firmware or restore eeprom value or upload current eeprom value. Tftp update firmware this page provides user use tftp to update firmware. Start the tftp server, and copy firmware update version image file...

  • Page 120

    Airlive snmp-fsh2602mg user’s manual 108 restart switch. Restore configure file this page user can restore eeprom value, save image file before, form tftp server. Start the tftp server. Press on this page. Tftp server: type the ip of tftp server. Remote file name: type the image file name. Press ctr...

  • Page 121

    Airlive snmp-fsh2602mg user’s manual 109 backup configure file this page user can save current eeprom value to image file. Then go to the update configure page to restore the eeprom value. Start the tftp server. Press on this page. Tftp server: type the ip of tftp server. Remote file name: type the ...

  • Page 122

    Airlive snmp-fsh2602mg user’s manual 110 application examples vlan application used with switch vlan is a simple solution to protect your network against broadcast storming by creating segments based on layer2 ethernet information and avoiding the complexity and the heavy processing requirements of ...

  • Page 123

    Airlive snmp-fsh2602mg user’s manual 111 benefit of vans grouping users into logical networks for performance enhancement. Provides effective broadcasts containment between segmented ports, which prevents flooding of a network. Offers security by completely isolating from each other the different br...

  • Page 124

    Airlive snmp-fsh2602mg user’s manual 112 trunking application used with switch trucking allows you to increase the available bandwidth between switches by grouping ports into a trunk. Trunk can also be used to connect server to switches for higher bandwidth service required. You can use trucking to ...

  • Page 125

    Airlive snmp-fsh2602mg user’s manual 113 single ip – agent mode” application used with switch single ip is a management utility of network devices for administrator to access private ip devices through a single ip (real ip or private ip). By this utility, administrator can manage much more network d...

  • Page 126

    Airlive snmp-fsh2602mg user’s manual 114 no up-link limitation through gigabit port. Unlike stacking mode, up-link in agent mode can be achieved through any port rather than gigabit port only. This provides great flexibility as long as network administrator can access them, and hence gigabit ports c...

  • Page 127

    Airlive snmp-fsh2602mg user’s manual 115 2. Master and slave switches in different lan domain. In this example, master will manage 2 slave switches and 1 router in other ip domain. The differences from example1 are that administrator and master switch ip are in the other ip domain (192.168.1.0). Swi...

  • Page 128

    Airlive snmp-fsh2602mg user’s manual 116 switch ip: 192.168.223.101 gateway: 192.168.223.254 switch ip: 192.168.223.102 gateway: 192.168.223.254 master in wan domain and slaves in lan domain. This example gives the practice application for remote management. The differences from example 2 are that m...

  • Page 129

    Airlive snmp-fsh2602mg user’s manual 117 “single ip - stacking mode” application used with switch used with switch this switch provides traditional stacking mode to stack with maximum 16 switches by cascading their gigabit ports . This feature helps network administrator to easily use one switch ass...

  • Page 130

    Airlive snmp-fsh2602mg user’s manual 118 the significant characteristics of this switch are: 1. No redundant hardware required: unlike special requirement of connecting cable among “hardware stacking” switches, this switch provides the least demand as a gigabit module to build up a stacking set. The...

  • Page 131

    Airlive snmp-fsh2602mg user’s manual 119 an example of port-base stacking vlan port-base stacking vlan setting: switch: master (192.168.223.100) slaves (192.168.223.110, 192.168.223.120, 192.168.223.130, 192.168.223.140, 192.168.223.150) pc: pc-0(192.168.223.99) on port 22 of master (192.168.223.100...

  • Page 132

    Airlive snmp-fsh2602mg user’s manual 120 result: 1. Pc-0 can access both pc-01 and pc-02..

  • Page 133

    Airlive snmp-fsh2602mg user’s manual 121 2. Pc-0 can only access pc-02 only. Pc-01 will not reply.

  • Page 134

    Airlive snmp-fsh2602mg user’s manual 122 snmp-fsh2602mg management switch appendix a product specifications • hardware o 24 x 10/100base-tx nway, auto-sensing ports o auto mdi/mdi-x to eliminate needs for cross-over cabling o single module slot for optional 1-port or 2-port 1000base-t(copper), 1000b...

  • Page 135

    Airlive snmp-fsh2602mg user’s manual 123 o ieee 802.1p priority control o ieee 802.1q tag vlan o ieee 802.3ad link aggregation o ieee 802.1v protocol based vlan classification o rfc1213(rmon groups 1, 2, 3, 9), rfc1493 (bridge mib), and rfc1643(ether-like mib) • management interface o web o snmp man...

  • Page 136

    Airlive snmp-fsh2602mg user’s manual 124 o igmp o support 802.1p 2-level priority queuing o port-trunking flexible load distribution control and fail-over functions provide 7 trunk groups of up to 4 member ports within 26 ports lacp trunking o ingress port security mode o rmon group 1,2,3,9 o auto a...

  • Page 137

    Airlive snmp-fsh2602mg user’s manual 125 appendix b troubleshooting this appendix contains specific information to help you identify and solve problems. If your switch does not function properly, please make sure it is set up according to the instructions on the manual. If you suspect your switch is...