1. DL manuals
  2. AirLive
  3. Adapter
  4. WMM-3000PCI
  5. User Manual

AirLive WMM-3000PCI User Manual

Manual is about: MIMO-G Wireless LAN Adapter

Summary of WMM-3000PCI

  • Page 1

    Wmm-3000pcm/pci mimo-g wireless lan adapter user’s manual.

  • Page 2

    Production component this wireless production should contain the following items: 1. One piece of cardbus or pci adapter mimo wireless lan card 2. One piece of cd which contain drivers, user’s manual, and utility quick installation 1. Insert the product’s cd into cd-rom. 2. Exit all application prog...

  • Page 3

    Fcc rf radiation exposure statement: 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with fcc rf radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operat...

  • Page 4: Contents

    Contents chapter 1 system requirements ___________________________ 5 1-1 hardware _______________________________________________________________ 5 1-2 software ________________________________________________________________ 5 chapter 2 install driver for windows series_________________ 6 2-1 set u...

  • Page 5

    5-5 configure connection with wpa2-psk ___________________________________ 38 5-6 configure connection with wpa by 802.1x setting _________________________ 41 5-7 configure connection with wpa2 by 802.1x setting________________________ 50 - 4 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 6: 1-1   Hardware

    Chapter 1 system requirements before installing the adapter and related software, make sure the computer system meets the minimum requirements described below. 1-1 hardware the adapter can be installed in any recent-model ibm-type microcomputer with a pcmcia on notebook or pci slot on desktop which ...

  • Page 7

    Chapter 2 install driver for windows series this section describes the installation of the 11b/g mimo wireless lan card driver for the windows98/me/2000 and windows xp operating systems. 2-1 set up mimo wireless lan card for windows series step 1: after inserting the mimo wireless lan card into the ...

  • Page 8

    Step 3: after installing the driver, you can check if your device is active in the device management as follows - 7 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 9: Lan Card

    Chapter 3 configure mimo wireless lan card this chapter will show you how to configure your mimo wireless lan card by using utility in the product cd package under windows series operation system 3-1 install utility 1. After finishing the install process, you can execute the utility as follows 3. Yo...

  • Page 10

    4. If your operation system belong to windows xp and have update to sp1, click the right button on the icon. You will see the frame below. If you want to configure your mimo wireless lan card with “wireless zero configure” supported by xp, you should choose “use zero configuration as configuration u...

  • Page 11

    3-2 configure mimo wireless lan card with zero configure after installing mimo wireless lan card, the windows xp will display a “wireless network connection ” message. Click on the message and the “automatic wireless network configuration” will then appear automatically and allow users to connect to...

  • Page 12

    2. Click properties to continue 3. Click wireless networks to reconfigure the wireless network connection. 4. If you need a key(wep) to connect the wireless network, you should keyin the key that supported by the wireless network router or access point - 11 - airlive mimo-g wireless lan adapter user...

  • Page 13

    Note: under the windows xp, it is recommend to use the “automatic wireless network configuration” to configure your mimo-g wireless lan card. The wireless lan utility comes with the wireless lan card is not support the windows xp. - 12 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 14: Chapter 4   Configure With

    Chapter 4 configure with “airlive mimo wireless utility” for windows 98/me/2000/xp 4-1 site survey page 1 . The means of item z ssid : name of ap z bssid : mac address of ap z signal : signal strength of ap z channel : ap used channel z encryption : what encrypted mechanism does ap used, the encrypt...

  • Page 15

    2 . The connected ap z the system will choose the suitable ap when you start up utility in the first time z if you want to connect with another ap, double click mouse’s left button in the ssid of ap. Z indicate connect successful. 3 . If the connect is success, it will show the ssid of the connected...

  • Page 16

    1. Profile name: different ap can be set up into different profile name 2. Ssid: the drop-down menu can select which ap is detected by system 3. Power save mode: can select［cam（constantly awake mode）］ or ［power saving mode］ mode. Selecting the” cam when ac power” means the power saving mode can auto...

  • Page 17

    4-2 authentication & security as shown in picture . When the encryption feature is enabled, the other setups are same as the said wep setting. 1. Authentication type: there are three type of authentication modes supported by utility . They are open, shared, wpa-psk and wpa system. 2. 802.1x setting:...

  • Page 18

    Iii. Ascii、40bits：5 ascii characters. Iv. Ascii、128bits：13 ascii characters. 4-2-1 802.1x setting 802.1x is a authentication for 『wpa』and 『wpa2』certificate to server. Show as figure 1. Authentication type: i. Peap: protect extensible authentication protocol. Peap transport securely authentication da...

  • Page 19

    Encrypted channel. Unlike eap-tls, eap-ttls requires only server-side certificates. Iv. Leap: light extensible authentication protocol. It is an eap authentication type used primarily in cisco aironet wlans. It encrypts data transmissions using dynamically generated wep keys, and supports mutual aut...

  • Page 20

    - 19 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 21: 4-3 Profile Page

    4-3 profile page profile can book keeping your favorite wireless setting among your home, office, and other public hotspot. You may save multiple profiles, and activate the correct one at your preference. 1. Definition of each field: i. Profile: name of profile, preset to prof* (* indicate 1, 2, 3,)...

  • Page 22: 4-4   Link Status Page

    4-4 link status page show the information of linking status. As show in picture 20, the description of each session is said as following: 1. Status: current connection status. If no connection, if will show disconnected. Otherwise, the ssid and bssid will show here. 2. Extra info: display link statu...

  • Page 23: 4-5 Statistics Page

    4-5 statistics page statistics page displays the detail counter information based on 802.11 mib counters. This page translates that mib counters into a format easier for user to understand. 1. Transmit statistics: i. Frames transmitted successfully: frames successfully sent. Ii. Frames transmitted s...

  • Page 24

    Advance page the advance setting is shown as follows. The description of each session is said as following: 1. Wireless mode: select wireless mode. 802.11b only, 802.11 b/g mixed 802.11a only, 802.11 a/b/g mixed and 802.11g only modes are supported. 2. 11b/g protection: erp protection mode of 802.11...

  • Page 25: 4-6   About Page

    4-6 about page about page display the wireless card and driver version information shown as follow figure . 1. Connect to airlive website: www.Airlive.Com 2. Display configuration utility, driver, - 24 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 26: Chapter 5 Example

    Chapter 5 example 5-1 adding profile in site survey page 1. Select the indented network from site survey list. 2. Click add profile. 3. System will pop up add profile windows - 25 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 27

    4. Change profile name from prof1 to favorite. 5. Click ok without changing other value. - 26 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 28

    - 27 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 29

    5-2 add profile in profile page 1. Click add in profile page 2. Add profile page will pop up 3. Change profile name to test. - 28 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 30

    4. Pull down ssid and select one intended ap. The ap list is the result of last site survey. 5. Set power saving mode. - 29 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 31

    6. Click authentication & security page 7. Click ok. Then we can find the profile name appears in the grid. - 30 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 32

    8. Click activate. Activate the profile setting. - 31 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 33: 5-3   Wep Encryption

    5-3 wep encryption 1. Select ap with wep encryption. 2. Click connect or doucle click intended network. 3. Authentication & security page pop up. - 32 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 34

    4. Enter 0123456789 at key#1 which is same as our intended ap’s setting. 5. Click ok. The result will look like the below figure. - 33 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 35

    - 34 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 36

    5-4 configure connection with wpa-psk 1. Select the ap with wpa-psk authentication mode. 2. Click connect or double click the intended network. 3. Authentication & security page will pop up. - 35 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 37

    *if ap setup security to 〝both 〞(tkip + aes), system define is aes that security is severely. 4. Authentication type is wpa-psk. Select correct encryption (tkip or aes).Enter wpa pre-shared keysecret as 01234567. 5. Click ok. Be careful, if the wpa pre-shared key entered is not correct, even though ...

  • Page 38

    Can be connected, but you won’t be able to exchange any data frames. - 37 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 39

    5-5 configure connection with wpa2-psk 1. Select the ap with wpa2-psk authentication mode. 2. Click connect or double click the intended network. 3. Authentication & security page will pop up. Tkip, aes and both (tkip+aes) security are - 38 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 40

    Support. *if ap setup security to 〝both 〞(tkip + aes), system define is aes that security is severely. 4. Authentication type is wpa-psk. Select correct encryption (tkip or aes). Enter wpa pre-shared keysecret as 12345678. 5. Click ok. Be careful, if the wpa pre-shared key entered is not correct, ev...

  • Page 41

    Can be connected, but you won’t be able to exchange any data frames. - 40 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 42

    5-6 configure connection with wpa by 802.1x setting 1. Select a.P with wpa authentication mode. 2. Click connect or double click the intended network 3. Authentication & security page will pop up. Tkip, aes and both (tkip+aes) security are - 41 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 43

    Support. *if ap setup security to 〝both 〞(tkip + aes), system define is aes that security is severely. 4. Click 802.1x setting. 5. 802.1x setting page will pop up. - 42 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 44

    6. Authentication type and setting method: 1. Peap: i. Authentication type chooses peap, key identity into wpatest2. Protocol chooses eap-mschap v2 for tunnel authentication, tunnel identity is wpatest2 and tunnel password is test2. Those setting are same as our intended ap’s setting. - 43 - airlive...

  • Page 45

    Ii. Click ok. The result will look like the below figure. 2. Tls / smart card: - 44 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 46

    I. Authentication type chooses tls / smart card, tls only need identity that is wpatest2 for server authentication. Ii. Tls must use client certicate. Click more to choose certicate. Iii. Certicate page will pop up; choose a certicate for server authentication. - 45 - airlive mimo-g wireless lan ada...

  • Page 47

    Iv. Display certicate information in use client certicate page. V. Click ok. The result will look like the below figure. - 46 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 48

    3. Ttls: i. Authentication type chooses ttls, identity is wpatest2. Protocol chooses chap for tunnel authentication, tunnel identity is wpatest2 and tunnel password is test2. Those setting are same as our intended ap’s setting. - 47 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 49

    Ii. Click ok. The result will look like the below figure. - 48 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 50

    4. Md5: i. Authentication type chooses md5, md5 only need identity and password that are wpatest2 and test2 for server authentication. Ii. Click ok. The result will look like the below figure. - 49 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 51

    5-7 configure connection with wpa2 by 802.1x setting 1. Select a.P with wpa2 authentication mode. 2. Click connect or double click the intended network. 3. Authentication & security page will pop up. Tkip, aes and both (tkip+aes) security are - 50 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 52

    Support. *if ap setup security to 〝both 〞(tkip + aes), system define is aes that security is severely. 4. Click 802.1x setting. 5. 802.1x setting page will pop up. - 51 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 53

    6. Authentication type and setting method: 1. Peap: i. Authentication type chooses peap, key identity into wpatest2. Protocol chooses eap-mschap v2 for tunnel authentication, tunnel identity is wpatest2 and tunnel password is test2. Those setting are same as our intended ap’s setting. - 52 - airlive...

  • Page 54

    Ii. Click ok. The result will look like the below figure. 2. Tls / smart card: - 53 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 55

    I. Authentication type chooses tls / smart card, tls only need identity that is wpatest2 for server authentication. Ii. Tls must use client certicate. Click more to choose certicate. Iii. Certicate page will pop up; choose a certicate for server authentication. - 54 - airlive mimo-g wireless lan ada...

  • Page 56

    Iv. Display certicate information in use client certicate page. V. Click ok. The result will look like the below figure. - 55 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 57

    3. Ttls: i. Authentication type chooses ttls, identity is wpatest2. Protocol chooses chap for tunnel authentication, tunnel identity is wpatest2 and tunnel password is test2. Those setting are same as our intended ap’s setting. Ii. Click ok. The result will look like the below figure. - 56 - airlive...

  • Page 58

    4. Md5: i. Authentication type chooses md5, md5 only need identity and password that are wpatest2 and test2 for server authentication. - 57 - airlive mimo-g wireless lan adapter user’s manual.

  • Page 59

    Ii. Click ok. The result will look like the below figure. - 58 - airlive mimo-g wireless lan adapter user’s manual.