1. DL manuals
  2. AirLive
  3. Wireless Router
  4. WT-2000R
  5. User Manual

AirLive WT-2000R User Manual

Other manuals for WT-2000R: Spec Sheet
Manual is about: Turbo-G Wireless Broadband Router

Summary of WT-2000R

  • Page 1

    Wt-2000r turbo-g wireless broadband router user’s manual airlive wt-200r user’s manual 1.

  • Page 2

    Copyright the contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise,...

  • Page 3

    Table of contents chapter 1 introduction .............................................................................. 4 functions and features......................................................................... 4 packing list.......................................................................

  • Page 4

    C c c h h h a a a p p p t t t e e e r r r 1 1 1 i i i n n n t t t r r r o o o d d d u u u c c c t t t i i i o o o n n n congratulations on your purchase of this outstanding wireless broadband router. This product is specifically designed for small office and home office needs. It provides a complete...

  • Page 5

    Wireless functions z high speed for wireless lan connection up to 54mbps data rate by incorporating orthogonal frequency division multiplexing (ofdm). Z roaming provides seamless roaming within the ieee 802.11b (11m) and ieee 802.11g (54m) wlan infrastructure. Z ieee 802.11b compatible (11m) allowin...

  • Page 6

    Advanced functions z system time supported allow you to synchronize system time with network time server. Z e-mail alert supported the router can send its info by mail. Z dynamic dns supported at present,the router has 3 ddns.Dyndns,tzo.Com and dhs.Org. Z snmp supported the router supports basic snm...

  • Page 7

    C c c h h h a a a p p p t t t e e e r r r 2 2 2 h h h a a a r r r d d d w w w a a a r r r e e e i i i n n n s s s t t t a a a l l l l l l a a a t t t i i i o o o n n n 2.1 panel layout 2.1.1. Front panel figure 2-1 front panel led: ports: port description pwr power inlet wan the port where you will ...

  • Page 8

    2.1.2. Rear panel figure 2-2 rear panel led: led function color status description power power indication green on power is being applied to this product. Status system status green blinking status is flashed once per second to indicate system is alive. Wan wan port activity green on the wan port is...

  • Page 9

    2.2 procedure for hardware installation 2. Decide where to place your wireless broadband router you can place your wireless broadband router on a desk or other flat surface, or you can mount it on a wall. For optimal performance, place your wireless broadband router in the center of your office (or ...

  • Page 10

    C c c h h h a a a p p p t t t e e e r r r 3 3 3 n n n e e e t t t w w w o o o r r r k k k s s s e e e t t t t t t i i i n n n g g g s s s a a a n n n d d d s s s o o o f f f t t t w w w a a a r r r e e e i i i n n n s s s t t t a a a l l l l l l a a a t t t i i i o o o n n n to use this product corr...

  • Page 11

    C c c h h h a a a p p p t t t e e e r r r 4 4 4 c c c o o o n n n f f f i i i g g g u u u r r r i i i n n n g g g w w w i i i r r r e e e l l l e e e s s s s s s b b b r r r o o o a a a d d d b b b a a a n n n d d d r r r o o o u u u t t t e e e r r r this product provides web based configuration sc...

  • Page 12

    4.1 start-up and log in activate your browser, and disable the proxy or add the ip address of this product into the exceptions. Then, type this product’s ip address in the location (for netscape) or address (for ie) field and press enter. For example: http://192.168.1.254. After the connection is es...

  • Page 13

    4.2 status this option provides the function for observing this product’s working status: a. Wan port status. If the wan port is assigned a dynamic ip, there may appear a “renew” or “release” button on the sidenote column. You can click this button to renew or release ip manually. B. Statistics of w...

  • Page 14

    4.3 wizard setup wizard will guide you through a basic configuration procedure step by step.Press ”next >” setup wizard - select wan type: for detail settings, please refer to 4.4.1 primary setup. Airlive wt-200r user’s manual 14.

  • Page 15

    4.4 basic setting 4.4.1 primary setup – wan type, virtual computers press “change” airlive wt-200r user’s manual 15.

  • Page 16

    This option is primary to enable this product to work properly. The setting items and the web appearance depend on the wan type. Choose correct wan type before you start. 1. Lan ip address:the local ip address of this device. The computers on your network must use the lan ip address of your product ...

  • Page 17

    4.4.1.3 dynamic ip address with road runner session management.(e.G. Telstra bigpond) 1. Lan ip address is the ip address of this product. It must be the default gateway of your computers. 2. Wan type is dynamic ip address. If the wan type is not correct, change it! 3. Host name: optional. Required ...

  • Page 18

    2. Server ip address: the ip address of the pptp server. 3. Pptp account and password: the account and password your isp assigned to you. If you don't want to change the password, keep it empty. 3. Connection id: optional. Input the connection id if your isp requires it. 4. Maximum idle time: the ti...

  • Page 19

    4.4.1.6 l2tp first,please check your isp assigned and select static ip address or dynamic ip address. For example:use static 1. My ip address and my subnet mask: the private ip address and subnet mask your isp assigned to you. 2. Server ip address: the ip address of the pptp server. 3. Pptp account ...

  • Page 20

    4.4.1.7 virtual computers(only for static and dynamic ip address wan type) virtual computer enables you to use the original nat feature, and allows you to setup the one-to-one mapping of multiple global ip address and local ip address. Airlive wt-200r user’s manual 20

  • Page 21

    • global ip: enter the global ip address assigned by your isp. • local ip: enter the local ip address of your lan pc corresponding to the global ip address. • enable: check this item to enable the virtual computer feature. 4.4.2 dhcp server press “more>>” the settings of a tcp/ip environment include...

  • Page 22

    This function enables you to assign another gateway to your pc, when dhcp server offers an ip to your pc. 4.4.3 wireless setting, 802.1x setting and wds wireless settings allow you to set the wireless configuration items. 1. Wireless : the user can enable or disalbe wireless function. 2. Network id ...

  • Page 23

    5. Wep key 1, 2, 3 & 4: when you enable the 128 or 64 bit wep key security, please select one wep key to be used and input 26 or 10 hexadecimal (0, 1, 2…8, 9, a, b…f) digits. 6. Pass-phrase generator: since hexadecimal characters are not easily remembered, this device offers a conversion utility to ...

  • Page 24

    If you select hex,you have to fill in 64 hexadecimal (0, 1, 2…8, 9, a, b…f) digits if ascii,the length of preshare key is from 8 to 63. 2. Fill in the key, ex 12345678 wpa check box was used to switch the function of the wpa. When the wpa function is enabled, the wireless user must authenticate to t...

  • Page 25

    Wpa2-psk(aes) 1. Select pre-share key mode if you select hex, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, a, b…f) digits if ascii, the length of pre-share key is from 8 to 63. 2. Fill in the key, ex 12345678 airlive wt-200r user’s manual 25.

  • Page 26

    Wpa2(aes) check box was used to switch the function of the wpa. When the wpa function is enabled, the wireless user must authenticate to this router first to use the network service. Radius server ip address or the 802.1x server’s domain-name. Select radius shared key if you select hex, you have to ...

  • Page 27

    Wpa-psk /wpa2-psk the router will detect automatically which security type(wpa-psk version 1 or 2) the client uses to encrypt. 1. Select pre-share key mode if you select hex, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, a, b…f) digits if ascii, the length of pre-share key is from 8 to 63. 2. Fi...

  • Page 28

    Wpa/wpa2 check box was used to switch the function of the wpa. When the wpa function is enabled, the wireless user must authenticate to this router first to use the network service. Radius server the router will detect automatically which security type(wpa-psk version 1 or 2) the client uses to encr...

  • Page 29

    Wds(wireless distribution system) wds operation as defined bythe ieee802.11 standard has been made available. Using wds it is possible to wirelessly connect access points, and in doing so extend a wired infrastructure to locations where cabling is not possible or inefficient to implement. Airlive wt...

  • Page 30

    4.5 port forwarding 4.5.1 virtual server airlive wt-200r user’s manual 30

  • Page 31

    This product’s nat firewall filters out unrecognized packets to protect your intranet, so all hosts behind this product are invisible to the outside world. If you wish, you can make some of them accessible by enabling the virtual server mapping. A virtual server is defined as a service port, and all...

  • Page 32

    4.5.2 special ap some applications require multiple connections, like internet games, video conferencing, internet telephony, etc. Because of the firewall function, these applications cannot work with a pure nat router. The special applications feature allows some of these applications to work with ...

  • Page 33

    4.5.3 miscellaneous items ip address of dmz host dmz (demilitarized zone) host is a host without the protection of firewall. It allows a computer to be exposed to unrestricted 2-way communication for internet games, video conferencing, internet telephony and other special applications. Note: this fe...

  • Page 34

    4.6 security settings airlive wt-200r user’s manual 34.

  • Page 35

    4.6.1 packet filter packet filter enables you to control what packets are allowed to pass the router. Outbound filter applies on all outbound packets. However, inbound filter applies on packets that destined to virtual servers or dmz host only. You can select one of the two filtering policies: 1. Al...

  • Page 36

    For source or destination port, you can define a single port (80) or a range of ports (1000-1999). Add prefix "t" or "u" to specify tcp or udp protocol. For example, t80, u53, u2000-2999. No prefix indicates both tcp and udp are defined. An empty implies all port addresses. Packet filter can work wi...

  • Page 37

    Others are all blocked. Example 2: (1.2.3.100-1.2.3.119) they can do everything except read net news (port 119) and transfer files via ftp (port 21) others are all allowed. After inbound packet filter setting is configured, click the save button. Outbound filter: to enable outbound packet filter cli...

  • Page 38

    (192.168.1.100-192.168.1.149) they are allowed to send mail (port 25), receive mail (port 110), and browse internet (port 80); port 53 (dns) is necessary to resolve the domain name. (192.168.1.10-192.168.1.20) they can do everything (block nothing) others are all blocked. Airlive wt-200r user’s manu...

  • Page 39

    Example 2: (192.168.1.100-192.168.1.119) they can do everything except read net news (port 119) and transfer files via ftp (port 21) others are allowed after outbound packet filter setting is configured, click the save button. Airlive wt-200r user’s manual 39.

  • Page 40

    4.6.2 domain filter domain filter let you prevent users under this device from accessing specific urls. Domain filter enable check if you want to enable domain filter. Log dns query check if you want to log the action when someone accesses the specific urls. Privilege ip addresses range setting a gr...

  • Page 41

    In this example: 1. Url include “www.Msn.Com” will be blocked, and the action will be record in log-file. 2. Url include “www.Sina.Com” will not be blocked, but the action will be record in log-file. 3. Url include “www.Google.Com” will be blocked, but the action will not be record in log-file. 4. I...

  • Page 42

    4.6.3 url blocking url blocking will block lan computers to connect to pre-defined websites. The major difference between “domain filter” and “url blocking” is domain filter require user to input suffix (like .Com or .Org, etc), while url blocking require user to input a keyword only. In other words...

  • Page 43

    In this example: 1. Url include “msn” will be blocked, and the action will be record in log-file. 2. Url include “sina” will be blocked, but the action will be record in log-file 3. Url include “cnnsi” will not be blocked, but the action will be record in log-file. 4. Url include “espn” will be bloc...

  • Page 44

    4.6.4 mac address control mac address control allows you to assign different access right for different users and to assign a specific ip address to a certain mac address. Mac address control check “enable” to enable the “mac address control”. All of the settings in this page will take effect only w...

  • Page 45

    Allow or deny the clients, whose mac addresses are not in the "control table", to associate to the wireless lan. Control table "control table" is the table at the bottom of the "mac address control" page. Each row of this table indicates the mac address and the expected ip address mapping of a clien...

  • Page 46

    Previous page and next page to make this setup page simple and clear, we have divided the “control table” into several pages. You can use these buttons to navigate to different pages. Airlive wt-200r user’s manual 46.

  • Page 47

    Example: in this scenario, there are three clients listed in the control table. Clients 1 and 2 are wireless, and client 3 is wired. 1.The "mac address control" function is enabled. 2."connection control" is enabled, and all of the wired and wireless clients not listed in the "control table" are "al...

  • Page 48

    6.Clients 1 and 2 are allowed to associate to the wireless lan, but a wireless client with a mac address not specified in the control table is denied to associate to the wireless lan. Client 3 is a wired client and so is not affected by association control. 4.6.5 miscellaneous items remote administr...

  • Page 49

    Port address, ack, seq number and so on. And the router will check every incoming packet to detect if this packet is valid. Dos attack detection when this feature is enabled, the router will detect and log the dos attack comes from the internet. Currently, the router can detect the following dos att...

  • Page 50

    4.7.1 system time get date and time by ntp protocol selected if you want to get date and time by ntp protocol. Time server select a ntp time server to consult utc time time zone select a time zone where this device locates. Set date and time manually selected if you want to set date and time manuall...

  • Page 51

    4.7.2 system log this page support two methods to export system logs to specific destination by means of syslog(udp) and smtp(tcp). The items you have to setup including: ip address for syslog host ip of destination where syslogs will be sent to. Check enable to enable this function. E-mail alert en...

  • Page 52

    4.7.3 dynamic dns to host your server on a changing ip address, you have to use dynamic domain name service (ddns). So that anyone wishing to reach your host only needs to know the name of it. Dynamic dns will map the name of your host to your current ip address, which changes each time you connect ...

  • Page 53

    Username/e-mail password/key you will get this information when you register an account on a dynamic dns server. Example: after dynamic dns setting is configured, click the save button. Airlive wt-200r user’s manual 53.

  • Page 54

    4.7.4 snmp setting in brief, snmp, the simple network management protocol, is a protocol designed to give a user the capability to remotely manage a computer network by polling and setting terminal values and monitoring network events. Enable snmp you must check either local or remote or both to ena...

  • Page 55

    4.7.5 routing routing tables allow you to determine which physical interface address to use for outgoing ip data grams. If you have more than one routers and subnets, you will need to enable routing table to allow packets to find proper routing path and allow different subnets to communicate with ea...

  • Page 56

    Example: configuration on nat router destination subnetmask gateway hop enabled 192.168.1.0 255.255.255.0 192.168.1.216 1 ˇ 192.168.0.0 255.255.255.0 192.168.1.103 1 ˇ so if, for example, the client3 wanted to send an ip data gram to 192.168.0.2, it would use the above table to determine that it had...

  • Page 57

    4.7.6 schedule rule you can set the schedule time to decide which service will be turned on or off. Select the “enable” item. Press “add new rule” airlive wt-200r user’s manual 57.

  • Page 58

    You can write a rule name and set which day and what time to schedule from “start time” to “end time”. The following example configure “ftp time” as everyday 14:10 to 16:20 after configure rule 1Æ airlive wt-200r user’s manual 58.

  • Page 59

    Schedule enable selected if you want to enable the scheduler. Edit to edit the schedule rule. Delete to delete the schedule rule, and the rule# of the rules behind the deleted one will decrease one automatically. Schedule rule can be apply to virtual server and packet filter, for example: exanple1: ...

  • Page 60

    4.8 maintenance airlive wt-200r user’s manual 60

  • Page 61

    4.8.1 change password you can change password here. We strongly recommend you to change the system password for security reason. Airlive wt-200r user’s manual 61.

  • Page 62

    4.8.2 system log you can view system log by clicking the view log button airlive wt-200r user’s manual 62.

  • Page 63

    4.8.3 firmware upgrade you can upgrade firmware by clicking firmware upgrade button. 4.8.4 backup setting you can backup your settings by clicking the backup setting button and save it as a bin file. Once you want to restore these settings, please click firmware upgrade button and use the bin file y...

  • Page 64

    You can also reset this product to factory default by clicking the reset to default button. 4.8.6 reboot you can also reboot this product by clicking the reboot button. 4.8.7 miscellaneous items airlive wt-200r user’s manual 64.

  • Page 65

    Mac address for wake-on-lan wake-on-lan is a technology that enables you to power up a networked device remotely. In order to enjoy this feature, the target device must be wake-on-lan enabled and you have to know the mac address of this device, say 00-11-22-33-44-55. Clicking "wake up" button will m...

  • Page 66

    A a a p p p p p p e e e n n n d d d i i i x x x a a a t t t c c c p p p / / / i i i p p p c c c o o o n n n f f f i i i g g g u u u r r r a a a t t t i i i o o o n n n f f f o o o r r r w w w i i i n n n d d d o o o w w w s s s 9 9 9 5 5 5 / / / 9 9 9 8 8 8 this section introduces you how to install...

  • Page 67

    6. The tcp/ip protocol shall be listed in the network window. Click ok to complete the install procedure and restart your pc to enable the tcp/ip protocol. A.2 set tcp/ip protocol for working with nat router 1. Click start button and choose settings, then click control panel. 2. Double click network...

  • Page 68

    A. Select obtain an ip address automatically in the ip address tab. B. Don’t input any value in the gateway tab. Airlive wt-200r user’s manual 68.

  • Page 69

    C. Choose disable dns in the dns configuration tab. B. Configure ip manually a. Select specify an ip address in the ip address tab. The default ip address of this product is 192.168.1.254. So please use 192.168.1.Xxx (xxx is between 1 and 253) for ip address field and 255.255.255.0 for subnet mask f...

  • Page 70

    B. In the gateway tab, add the ip address of this product (default ip is 192.168.1.254) in the new gateway field and click add button. C. In the dns configuration tab, add the dns values which are provided by the isp into dns server search order field and click add button. Airlive wt-200r user’s man...

  • Page 71

    A a a p p p p p p e e e n n n d d d i i i x x x b b b 8 8 8 0 0 0 2 2 2 . . . 1 1 1 x x x s s s e e e t t t t t t i i i n n n g g g figure 1: testing environment (use windows 2000 radius server) 1 equipment details pc1: microsoft windows xp professional without service pack 1. Amit 531c wireless car...

  • Page 72

    5.Set radius server shared key. 6.Configure wep key and 802.1x setting. The following test will use the inbuilt 802.1x authentication method such as ,eap_tls, peap_chapv2(windows xp with sp1 only), and peap_tls(windows xp with sp1 only) using the smart card or other certificate of the windows xp pro...

  • Page 73

    Figure 2: enable ieee 802.1x access control airlive wt-200r user’s manual 73.

  • Page 74

    Figure 3: smart card or certificate properties 4. Windows 2000 radius server authentication testing: 4.1dut authenticate pc1 using certificate. (pc2 follows the same test procedures.) 1. Download and install the certificate on pc1. (fig 4) 2. Pc1 choose the ssid of dut as the access point. 3. Set au...

  • Page 75

    Figure 4: certificate information on pc1 figure 5: authenticating figure 6: authentication success 4.2dut authenticate pc2 using peap-tls. 1. Pc2 choose the ssid of dut as the access point. 2. Set authentication type of wireless client and radius server both to peap_tls. 3. Disable the wireless conn...

  • Page 76

    And end the authentication procedure. 6. Terminate the test steps when pc2 get dynamic ip and ping remote host successfully. Support type: the router supports the types of 802.1x authentication: peap-chapv2 and peap-tls. Note. 1.Pc1 is on windows xp platform without service pack 1. 2.Pc2 is on windo...

  • Page 77

    Or another configuration: w pa-psk in fact, it is not necessary for this function to authenticate by radius server, the client and wireless router authenticate by themselves. Method1: 1. Go to the web manager of wireless router to configure, like below: 2. Go to odyssey client manager, first choose ...

  • Page 78

    3. Add and edit some settings: airlive wt-200r user’s manual 78.

  • Page 79

    4. Back to connection: then select “connect to network” you will see: method2: 1. First, patch windows xp and have to install “service package 1” patch: http://www.Microsoft.Com/downloads/details.Aspx?Displaylang=en&familyid=5039ef4a-61e0-4c44-94f0-c25 c9de0ace9 2. Then reboot. 3. Setting on the rou...

  • Page 80

    Choose “view available wireless networks” like below: advancedÆ choose “123kk” airlive wt-200r user’s manual 80

  • Page 81

    Wpa: for this function, we need the server to authenticate. This function is like 802.1x. The above is our environment: method 1: 1. The usera or userb have to get certificate from radius, first. Http://192.168.122.1/certsrv account : fae1 passwd : fae1 2. Then, install this certificate and finish. ...

  • Page 82

    4. Go to odyssey client manager, choose “profiles” and setup profile name as “1” login name and passwd are fae1 and fae1. Remember that you get certificate from radius in step1. Airlive wt-200r user’s manual 82.

  • Page 83

    5. Then choose “certificate” like above. 6. Then go to authentication and first remove eap/ tls and add eap/tls again. Airlive wt-200r user’s manual 83.

  • Page 84

    7. Go “network” and select “1” and ok airlive wt-200r user’s manual 84.

  • Page 85

    8. Back to connection and select “123kk. If successfully, the wireless client has to authenticate with radius server, like below: 9.Result: method 2: 1. The usera or userb have to get certificate from radius,first. Http://192.168.122.1/certsrv account:fae1 passwd:fae1 airlive wt-200r user’s manual 8...

  • Page 86

    2. Then install this certificate and finish. 3. Setting on the router and client: router: client: go to “network connection” and select wireless adapter. Choose “view available wireless networks” like below: advancedÆ choose “123kk” select “wirelessca and enable” in trusted root certificate authorit...

  • Page 87

    Then, if the wireless client wants to associate, it has to request to authenticate. Airlive wt-200r user’s manual 87.

  • Page 88

    A a a p p p p p p e e e n n n d d d i i i x x x d d d w w w d d d s s s s s s e e e t t t t t t i i i n n n g g g how to setup and work: first, check the wlan-mac address of ap1,ap2 and ap3.Please goto command mode and use “arp –a ”. If you can not find the information of mac, please make the cable ...

  • Page 89

    If the settings are ok,the client1 and client2 can get ip from dhcp server of ap1.Then client1 and client2 can get information each other. Ap1 setting: ap1ÅÆ ap2(remote mac: 00-50-18-00-0f-fd) ap1ÅÆ ap3(remote mac: 00-50-18-00-0f-fc) airlive wt-200r user’s manual 89.

  • Page 90

    Ap2 setting: ap2ÅÆ ap1(remote mac: 00-50-18-00-0f-fe) ap3 setting ap3ÅÆ ap1(remote mac: 00-50-18-00-0f-fe) airlive wt-200r user’s manual 90

  • Page 91

    Airlive wt-200r user’s manual 91.

  • Page 92

    A a a p p p p p p e e e n n n d d d i i i x x x e e e f f f a a a q q q a a a n n n d d d t t t r r r o o o u u u b b b l l l e e e s s s h h h o o o o o o t t t i i i n n n g g g what can i do when i have some trouble at the first time? 1. Why can i not configure the router even if the cable is plu...

  • Page 93

    Whatever i setup, the pc can not get ip. Please check status led and refer to the q2: 2.Why can i not connect the router even if the cable is plugged in lan port and the led is light? A: first, please check status led. If the device is normal, the led will blink per second. If not, please check how ...

  • Page 94

    About 8 times, the restore process is completed. However, if led flashes 2 times, repeat. 2. Restore directly when the router power on first, push the reset button about 5 seconds (status will start flashing about 5 times), remove the finger. The restore process is completed. 4.How to do recovery mo...

  • Page 95

    Step3:please use the exe-file of fw and click as below: then click” upgrade” if necessary, please input password ”admin” .Then reset to default and refer to q1 how to connect router. However, if those methods can not make the router normal, please send the unit to the seller to check, thanks. 5.Why ...

  • Page 96

    6.When i use static ip address to roam internet, i can access or ping global ip 202.93.91.218, but i can not access the site that inputs domain name, for example http://espn.Com ? A: please check the dns configuration of static ip address. Please refer to the information of isp and assign one or two...

  • Page 97

    How do i connect router by using wireless? 1.How to start to use wireless? A: first, make sure that you already installed wireless client device in your computer. Then check the configuration of wireless router. The default is as below: about wireless client, you will see wireless icon: then click a...

  • Page 98

    If successfully, the computer will show and get ip from router: 2.When i use aes encryption of wpa-psk to connect even if i input the correct pre-share key? A: first, you must check if the driver of wireless client supports aes encryption. Please refer to the below: if ssid is default and click “pro...

  • Page 99

    3.When i use wireless to connect the router, but i find the signal is very low even if i am close to the router? A: please check if the wireless client is normal, first. If yes, please send the unit to the seller and verify what the problem is. Airlive wt-200r user’s manual 99.