Airmar HT200 Owner's Manual & Installation Instructions
OWNER’S GUIDE & INSTALLATION INSTRUCTIONS
17
-4
22
-0
1 re
v.
0
6
03
/07
/16
Thru-Hull, Retractable with Valve
Temperature or Speed & Temp. Sensor
Models: HT200, ST850
U.S. Patents: 7,110,908; 7,352,171. UK 2 409 527
Applications
• Plastic housing recommended for fiberglass or metal hulls only.
Never install a plastic housing in a wood hull since swelling of
the wood may fracture the plastic.
• Bronze housing recommended for fiberglass or wood hull only.
Never mount a bronze housing in a metal hull because
electrolytic corrosion will occur.
Record the information found on the cable tag for future reference.
Part No._________________Date___________
Pretest
Connect the sensor to the instrument. Check for the approximate
air temperature. If it has a paddlewheel, spin it and check for a
speed reading. If there is no reading(s) or it is inaccurate, check
the connections and try again. If there is still a problem, return the
product to the place of purchase.
Tools & Materials
Safety goggles
Dust mask
Ear plugs
Water-based anti-fouling paint (mandatory in salt water)
Electric drill with 10mm (3/8") or larger chuck capacity
Drill bit
3mm or 1/8"
Hole saw:
51mm or 2"
Countersink tool (installing a flush housing)
Sandpaper
Mild household detergent or weak solvent (such as alcohol)
File (installation in a metal hull)
Marine sealant (suitable for below waterline)
Slip-joint pliers (installing a metal housing)
Grommet(s) (some installations)
Cable ties
Installation in a cored fiberglass hull (see page 4)
Hole saw for hull interior
60mm or 2-3/8"
Fiberglass cloth and resin
or Cylinder, wax, tape, and casting epoxy
Mounting Location
CAUTION: Never mount the speed sensor directly ahead of a
depth transducer, since turbulence generated by the
paddlewheel’s rotation will adversely affect the transducer’s
performance, especially at high speeds. Mount side by side.
CAUTION: Do not mount the sensor in line with or near water
intake or discharge openings or behind strakes, fittings, or hull
irregularities that may disturb the water flow.
Choose an accessible spot inside the vessel. Allow a minimum of
280mm (11") of headroom for the height of the housing, tightening
the nuts, and installing the insert.
HT200—The sensor must be in contact with the water at all times.
ST850—Turbulence-free water must flow under the paddlewheel
at all boat speeds.
Follow the precautions below for optimal
product performance and to reduce the risk of
property damage, personal injury, and/or death.
WARNING: Always wear safety goggles, a dust mask,
and ear plugs when installing.
WARNING: The valve is not a watertight seal! Always
use the insert or the blanking plug secured with the
safety wire for a watertight seal.
WARNING: The O-rings must be intact and well
lubricated to make a watertight seal.
WARNING:Always attach the safety wire to prevent
the insert or blanking plug from backing out in the
unlikely event that the cap nut fails or is screwed on
incorrectly.
WARNING: When the valve assembly is removed,
always insert the short emergency plug secured with
the CAP nutand safety wire for a watertight seal.
WARNING: Immediately check for leaks when the boat
is placed in the water. Do not leave the boat unchecked
for more than three hours. Even a small leak may allow
considerable water to accumulate.
CAUTION: Never pull, carry, or hold the sensor by its
cable; this may sever internal connections.
CAUTION: Never use a fairing with a plastic housing;
the protruding sensor would be vulnerable to damage
from impact.
CAUTION: Never install a metal housing in a vessel
with a positive ground system.
CAUTION: Never use solvents. Cleaner, fuel, sealant,
paint, and other products may contain solvents that
can damage plastic parts.
IMPORTANT: Please read the instructions completely
before proceeding with the installation. These
instructions supersede any other instructions in your
instrument manual if they differ.
low profile
P17 housing
plastic
ST850
low profile
P17 housing
plastic
HT200