1. DL manuals
  2. Anita
  3. Sewing Machine
  4. GP-510- 446(7)
  5. User Manual

Anita GP-510- 446(7) User Manual

Summary of GP-510- 446(7)

  • Page 1

    User manual and spare parts list gp-510- 446(7) anita b, s.R.O. Hliníky 2068 680 01 boskovice czech republic tel: +420 516454774, 516453496 fax: +420 516452751 e-mail: info@anita.Cz.

  • Page 2

    2.

  • Page 3

    3 anita-b gp-510-446(7) 1 safety measures do not put the machine into operation until an appropriate preparation is carried out by a specialist or an authorised person, and until you get acquainted with safety measures. 1. Any sewing machine may be operated only by a properly trained operator. 2. Ta...

  • Page 4

    4 anita-b gp-510-446(7) 2 putting the machine into operation following instructions must be observed to avoid risk of failures or damage to the machine: - clean the machine of preserving agents - drop 1-2 drops of oil into looper - remove the front cover and oil the ends of needle bar connecting-rod...

  • Page 5

    5 anita-b gp-510-446(7) 3 threading the upper thread caution! Switch off the main switch and remove your feet from the pedals on the machine support before threading so that the machine may not be started by unintended treading on the pedal. When threading the thread from bobbin stand into needle fo...

  • Page 6

    6 anita-b gp-510-446(7) 4 inserting needles caution ! Switch off the main switch and remove your feet from the pedals on the machine support before replacing needles so that the machine may not be started by unintended treading on the pedal. Fig.3 having chosen the right thickness (size) of needle w...

  • Page 7

    7 anita-b gp-510-446(7) caution! Do not start the machine until you put the hook covers in working (protecting) position. Switch off the main switch and remove your feet from the pedals on the machine support before replacing the hook bobbin so that the machine may not be started by unintended tread...

  • Page 8

    8 anita-b gp-510-446(7) 7 adjusting differential feed ratio (only for machines with driven presser foot) to ensure sewing of fabric layers without their displacement in the course of feeding it is possible to adjust different lengths of feeding driven by press-wheel and feeding by rotary feed dog. T...

  • Page 9

    9 anita-b gp-510-446(7) the sewing machines are equipped with a safety clutch on the lower shaft (a) fig. 8 that allows the operator to turn the driving part of lower shaft (a) when the loopers or feed dogs are locked. The clutch consists of segment (b) engaging with.Groove (c) in the disk on lower ...

  • Page 10

    10 anita-b gp-510-446(7) 10 switching off and switching on of the main switch the main switch are marked 0 and i or they have grey/green and red buttons. Pushing position of the button marked "0" (red) means: off, pushing position of the button marked "i" (grey/green) means on. Caution! Before you s...

  • Page 11

    11 anita-b gp-510-446(7) 12 bobbin winder – standard built in fig. 9 the thread passes from the bobbin stand through thread guide on the winder bracket (1) and between tension disks (2) and then following the direction of arrow (s) to the empty bobbin. Install the empty bobbin on the bobbin winder s...

  • Page 12

    12 anita-b gp-510-446(7) instructions for adjustment threat trimmer mechanism 13 basic condition a) clearance between the throat plate and the bobbin case stopper. Fig.10 condition : clearance between the top end of the bobbin case resting groove on the throat plate and the top face of the bobbin ca...

  • Page 13

    13 anita-b gp-510-446(7) c) the range of technological use needle: 134 lr size 90 – 180. According to the chosen material, threads and needle gauge it is necessary to choose throat plate insert and also throat plate (table i3- parts book) . Large hook. Sewing speed max.-1600(spm). Stitch length max....

  • Page 14

    14 anita-b gp-510-446(7) 16 to adjust the counter knife (fig. 14)(table i1,j-parts book) counter knife (i1/7) is located on the holder (i1/3). After releasing the screw (i1/19), mildly push the counter knife (i1/7) on the moving knife (i1/20) by the means of the excentric pin (i1/9) which means in t...

  • Page 15

    15 anita-b gp-510-446(7) 18 to adjust the thread trimming cam (fig.15)(table j,i1 – parts book) axial position of the trimming c am(j/1) is in contact with the axial ring (j/8). A)adjust the thread take up lever to top dead point. In this position, adjust the actuating cam using two screws (j/30) so...

  • Page 16

    16 anita-b gp-510-446(7) 20 to adjust the initial position of the moving knife (fig.16) adjust the moving knife (i1/20) into the initial position. A clearance of approx. 1 mm must be provided between the top end of the moving knife and of the counter knife. After then tighten the screw (j/27) in arm...

  • Page 17

    17 anita-b table of contents gp-510-446(7) spare parts lists a1 frame and cover parts……………………………………………..18,19 a2 thread tension mechanism………………………………………..20,21 b upper shaft mechanism………………………….………………..22,23 c1 lower shaft and clutch mechanism………………………………..24,25 c2 timing belt drivingmechanism………………...

  • Page 18

    18 anita-b frame and cover parts a1 gp-510-446(7).

  • Page 19

    19 anita-b frame and cover parts a1 gp-510-446(7) ref.No. Part no. Name of part q´ty a1-1 gp/1-5 face plate 1 a1-2 gp/108246 screw (m5x0,8x25) 1 a1-3 gp/108234 screw (m5x0,8x35) 1 a1-4 gp/168061 thread take-up cover 1 a1-5 gp/210210 screw (m5x0,8x8) 1 a1-6 gp/119027 4 hole thread retainer 1 a1-7 gp/...

  • Page 20

    20 anita-b thread tension mechanism a2 gp-510-446(7).

  • Page 21

    21 anita-b thread tension mechanism a2 gp-510-446(7) ref.No. Part no. Name of part q´ty a2-1 gp/119766-2 thread tension regulator assy/deska nap.úpl. 1 a2-2 gp/119171-25 thread tension regulator assy/deska nap.úpl. 0 a2-3 gp/egs3221 solenoid/magnet egs 3221 1 a2-4 gp/sm4-6 base plate/deska napína 1 ...

  • Page 22

    22 anita-b upper shaft mechanism b gp-510-446(7).

  • Page 23

    23 anita-b upper shaft mechanism b gp-510-446(7) ref.No. Part no. Name of part q´ty b-1 gp/119702-2 crank cam 1 b-2 gp/130224 screw (m5x0,8x12) 2 b-3 gp/119702-3 screw (m7x1,0x22) 1 b-4 gp/119702-4 screw (m7x1,0x16,5) 1 b-5 gp/700510 screw (m6x0,75x8) 3 b-6 gp/119702-5 bushing 1 b-7 gp/119702-1 uppe...

  • Page 24

    24 anita-b lower shaft and clutch mechanism c1 gp-510-446(7).

  • Page 25

    25 anita-b lower shaft and clutch mechanism c1 gp-510-446(7) ref.No. Part no. Name of part q´ty c1-1 gp/175025 shaft 1 c1-2 gp/518250 retaining ring 1 c1-3 gp/119711 shaft 1 c1-4 gp/175019 coupler 1 c1-5 gp/341901 screw (m6x0,75x6) 4 c1-6 gp/133109 coupler 1 c1-7 gp/119081a connecting plate 1 c1-7- ...

  • Page 26

    26 anita-b timing belt driving mechanism c2 gp-510-446(7).

  • Page 27

    27 anita-b c2 gp-510-446(7) ref.No. Part no. Name of part q´ty c2-1 gp/119097 plug 2 c2-2 gp/610300 retaining ring 1 c2-3 gp/018624 ball bearing 2 c2-4 gp/119707 timming belt wheel 1 c2-5 gp/335902-1 screw (m6x0,75x8) 2 c2-6 gp/335902 screw (m6x0,75x10) 2 c2-7 gp/119121 collar (left) 1 c2-8 gp/70068...

  • Page 28

    28 anita-b lower feed mechanism d2 gp-510-446(7).

  • Page 29

    29 anita-b lower feed mechanism d2 gp-510-446(7) ref.No. Part no. Name of part q´ty d2-1 gp/119795 roller bracket 1 d2-1-1 gp/119795-1 roller bracket 1 d2-1-2 gp/119795-2 roller bracket 1 d2-1-3 gp/119795-3 screw 3 d2-1-4 gp/119795-4 screw 3 d2-1-5 gp/119795-5 ball d.2mm 23 d2-2 gp/119737 bevel gear...

  • Page 30

    30 anita-b feed shaft mechanism d3 gp-510-446(7).

  • Page 31

    31 anita-b feed shaft mechanism d3 gp-510-446(7) ref.No. Part no. Name of part q´ty d3-1 gp/610280 retaining ring 1 d3-2 gp/119085 washer 1 d3-3 gp/133283 washer 6 d3-4 gp/215124 needle bearing 3 d3-5 gp/118600 bushing 1 d3-10 gp/119084 shaft 1 d3-11 gp/118601 bushing 1 d3-12 gp/119521 crank 1 d3-13...

  • Page 32

    32 anita-b stitch adjuster mechanism d4 gp-510-446(7).

  • Page 33

    33 anita-b stitch adjuster mechanism d4 gp-510-446(7) ref.No. Part no. Name of part q´ty d4-1 gp/175038 connecting rod 1 d4-2 gp/069060 ball bearing 1 d4-3 gp/175038a crank rod set 1 d4-4 gp/215028 needle bearing 1 d4-5 gp/118612 bearing stud 1 d4-6 gp/165356 feeding adjusting plate 1 d4-7 gp/165356...

  • Page 34

    34 anita-b needle bar feed and presser foot mechanism e gp-510-446(7).

  • Page 35

    35 anita-b needle bar feed and presser foot mechanism e gp-510-446(7) ref.No. Part no. Name of part q´ty e-7 gp/175096 needle bar 1 e-8 gp/174173 screw(m3x0,5x4) 1 e-9 gp/175096-2 thread guide 1 e-10 gp/175150 pin 1 e-11 gp/215028 needle bearing 2 e-12 gp/169137 washer (14x8x0.5) 2 e-13 gp/305305 sc...

  • Page 36

    36 anita-b thread take-up lever mechanism f gp-510-446(7).

  • Page 37

    37 anita-b thread take-up lever mechanism f gp-510-446(7) ref.No. Part no. Name of part q´ty f-1 gp/118084 thread take-up assy 1 f-2 gp/119009 take-up lever support stud 1 f-3 gp/168039 washer 2 f-4 gp/215022 needle bearing 2 f-5 gp/119008 take-up frame 1 f-6 gp/119762 take-up crank pin 1 f-7 gp/119...

  • Page 38

    38 anita-b roller presser foot mechanism g1 gp-510-446(7).

  • Page 39

    39 anita-b roller presser foot mechanism g1 gp-510-446(7) ref.No. Part no. Name of part q´ty g1-1 gp/119803 roller preser assy (large) 1 g1-2 gp/119803-1 roller preser assy (middle) 1 g1-3 gp/119802 roller preser assy (small) 2 g1-4 gp/119469 spring washer 2 g1-5 gp/033145 pin 1 g1-6 gp/175109 gear ...

  • Page 40

    40 anita-b presser foot bar mechanism g2 gp-510-446(7).

  • Page 41

    41 anita-b presser foot bar mechanism g2 gp-510-446(7) ref.No. Part no. Name of part q´ty g2-1 gp/119019 presser bar bushing (upper) 1 g2-2 gp/700785 screw (m5x0,8x6) 2 g2-3 gp/119018 presser bar bushing (upper) 1 g2-4 gp/118530 presser bar holder 1 g2-5 gp/700510 screw (m6x0,75x8) 2 g2-6 gp/119019-...

  • Page 42

    42 anita-b right side hook mechanism h1 gp-510-446(7).

  • Page 43

    43 anita-b right side hook mechanism h1 gp-510-446(7) ref.No. Part no. Name of part q´ty h1-1 gp/g400tl hook complete with bobbin case-large 1 h1-1-1 gp/g400tl-749 hook complete without cap 1 h1-1-2 gp/g400tl-102 hook without cap holder 1 h1-1-3 gp/g400t-017 tension spring fastening screw 1 h1-1-4 g...

  • Page 44

    44 anita-b right side hook post mechanism i1 gp-510-446(7).

  • Page 45

    45 anita-b right side hook post mechanism i1 gp-510-446(7) ref.No. Part no. Name of part q´ty i1-1 gp/sm2-3.1m hook post/chapa ový sloupek 1 i1-2 gp/250084 srew/šroub(m3x0.5x6) 2 i1-3 gp/410-449-004 holder/držák pevného nože 1 i1-4 gp/700336 screw/šroub(m4x0,7x6) 1 i1-5 gp/175318 stud/excentr 1 i1-6...

  • Page 46

    46 anita-b left side post mechanism i3 gp-510-446(7).

  • Page 47

    47 anita-b left side post mechanism i3 gp-510-446(7) ref.No. Part no. Name of part q´ty i3-1 gp/119145 cover plate/kryt 1 i3-2 gp/250084 screw/šroub(m3x0,5x6) 4 i3-3 gp/sm5-4.9m support plate/levý sloupek 1 i3-4 gp/119144 washer/podložka 2 i3-5 gp/130224 screw/šroub(m5x0,8x12) 2 i3-6 gp/182451 screw...

  • Page 48

    48 anita-b knife actuating mechanism j gp-510-446(7).

  • Page 49

    49 anita-b knife actuating mechanism j gp-510-446(7) ref.No. Part no. Name of part q´ty j-1 gp/sm4-20 cam/va ka 1 j-2 gp/sm4-21 holder/držák odst ihového magnetu 1 j-3 gp/sm2-1.3 lever/páka 1 j-4 gp/sm2-1.2 bracket/rameno 1 j-5 gp/sm2-1.6 pin/ ep 1 j-6 gp/sm2-1.7 roller/kladka 1 j-7 gp/sm2-1.5 plug/...

  • Page 50

    50 anita-b needle feed and driven roller mechanism k1 gp-510-446(7).

  • Page 51

    51 anita-b needle feed and driven roller mechanism k1 gp-510-446(7) ref.No. Part no. Name of part q´ty k1-1 gp/sm5-11.1 holder/držák 1 k1-2 gp/m5x12 screw/šroub m5x12 din 912 10 k1-3 gp/m5x16 screw/šroub m5x16 din 915 1 k1-4 gp/m5x30 screw/šroub m5x30 din 915 1 k1-5 gp/sm5-1.10 shaft/h ídel 1 k1-6 g...

  • Page 52

    52 anita-b left side post and lower backtacking feed mechanism k2 gp-510-446(7).

  • Page 53

    53 anita-b left side post and backtacking feed mechanism k2 gp-510-446(7) ref.No. Part no. Name of part q´ty k2-1 gp/sm5-21.3 rod/rameno sb 1 k2-2 gp/sm5-2.10 rod/rameno sj 1 k2-3 gp/sm5-2.12 rod/rameno zj 1 k2-4 gp/sm5-2.11 rod/rameno zb 1 k2-5 gp/m5x12 screw/šroub m5x12 din 912 4 k2-6 gp/174176 sc...

  • Page 54

    54 anita-b upper driven roller backtacking feed mechanism k3 gp-510-446(7).

  • Page 55

    55 anita-b upper driven roller backtacking feed mechanism k3 gp-510-446(7) ref.No. Part no. Name of part q´ty k3-1 gp/sm5-s31 shaft-set/h ídel úplná 1 k3-3 gp/sm5-31.37 washer/kroužek 1 k4-4 gp/sm5-31.33 oil felt/plst ný kroužek 1 k3-5 gp/130224 washer/podl.Dist. Din 988,10x16/0,5(+0,3) 1 k3-6 gp/br...

  • Page 56

    56 anita-b telescopic shaft driven roller mechanism k4 gp-510-446(7).

  • Page 57

    57 anita-b telescopic shaft driven roller mechanism k4 gp-510-446(7) ref.No. Part no. Name of part q´ty k4-1 gp/sm5-31.29 shaft/h ídel s kulovým kloubem 1 k4-2 gp/sm5-31.36 spring/tla ná pružina 1 k4-3 gp/sm5-31.31 shaft/h ídel 1 k4-4 gp/2,5m6x12 pin/kolík 2,5m6x12 din6325 1 k4-5 gp/sm5-31.32 clutch...

  • Page 58

    58 anita-b upper shaft driven roller mechanism k5 gp-510-446(7).

  • Page 59

    59 anita-b upper shaft driven roller mechanism k5 gp-510-446(7) ref.No. Part no. Name of part q´ty k5-1 gp/sm5-31.38 holder/držák 1 k5-2 gp/119163 crank/páka 1 k5-3 gp/119507 link/táhlo 2 k5-4 gp/174176 screw/šroub(m4x10) 4 k5-5 gp/119087 oil felt/plst ný kroužek 4 k5-6 gp/m5x12 screw/šroub m5x12 di...

  • Page 60

    60 anita-b rods lower backtacking mechanism k6 gp-510-446(7).

  • Page 61

    61 anita-b rods lower backtacking mechanism k6 gp-510-446(7) ref.No. Part no. Name of part q´ty k6- 1 gp/sm5-21.8 holder/držák 1 k6- 2 gp/sm5-21.2 rod/páka 1 k6- 3 gp/5m6x25 pin/kolík 5m6x25 din 12771a 1 k6- 4 gp/sm5-2.4 bracket/podp ra 1 k6- 5 gp/m6x40 screw/šroub m6x40 din 912 2 k6- 6 gp/sm5-2.8 n...

  • Page 62

    62 anita-b electric accessory k8 gp-510-446(7).

  • Page 63

    63 anita-b electric accessory k8 gp-510-446(7) ref.No. Part no. Name of part q´ty k8-1 gp/2x0,5 cabel/vodi kruh.Pr ez 2x0,5,l=1,5m 1 k8-2 gp/2x0,5 cabel/vodi kruh.Pr ez 2x0,5,l=1m 1 k8-3 gp/mate-n-lok connector mate-n-lok 1 k8-3-1 gp/ 1-480318-0 mate-n-lok/kryt dutinek 2p/kab 1 k8-3-2 gp/ 1-480319-0...

  • Page 64

    64 anita-b auto presser lifting solenoid mechanism l gp-510-446(7) ref. No. Part no. Name of part q´ty l- 1 gp/aevs072-4 solenoid/magnet aevs 072-4 175w 1 l- 2 gp/sm8-1 plate/držák 1 l- 3 gp/sm8-2 plug/trn 1 l- 4 gp/m5x10 screw/šroub m5x10 din 963a 3 l- 5 gp/m5x14 screw/šroub m5x14 din 912 4 l- 6 gp...

  • Page 65

    65 anita-b bobbin winder n1 gp-510-446(7) ref. No. Part no. Name of part q´ty n1-1 gp/gu-100t bobbin winder-built in 1 n1-2 d/d08082993000 knife 1 n1-3 d/d08028312900 spring 283129 1 n1-4 d/d08028313000 spring 283130 1 n1-5 p/p98002524800 thread retainer 1 n1-6 gp/m3x5 screw m3x5 din 84a 1 n1-7 gp/9...

  • Page 66

    66 anita-b accessories n2 gp-510-446(7).

  • Page 67

    67 anita-b accessories n gp-510-446(7) ref.No. Part no. Name of part q´ty n2-1 gp/123456 accessory bag 1 n2-2 gp/029836 vinyl cover 1 n2-3 gp/800110 spanner 1 n2-4 gp/129915 screw driver (small) 1 n2-5 gp/029946 screw driver (middle) 1 n2-6 gp/029007 screw driver (large) 1 n2-7 gp/134lr needle 10 n2...

  • Page 68

    68.