1. DL manuals
  2. Anritsu
  3. Microphone
  4. MS27101A
  5. Installation Manual

Anritsu MS27101A Installation Manual

Manual is about: Remote Spectrum Monitors

Summary of MS27101A

  • Page 1

    Installation guide remote spectrum monitors ms27101a, ms27102a, ms27103a 9 khz to 6 ghz anritsu company 490 jarvis drive morgan hill, ca 95037-2809 usa http://www.Anritsu.Com part number: 10580-00409 revision: c published: march 2016 copyright 2016 anritsu company.

  • Page 2: Table of Contents

    Ms2710xa ig pn: 10580-00409 rev. C contents-1 table of contents chapter 1—ms27101a installation 1-1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1-2 instrument overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 3: 1-1

    Ms2710xa ig pn: 10580-00409 rev. C 1-1 chapter 1 — ms27101a installation 1-1 introduction the ms27101a remote spectrum monitor can be ordered with optional rack mounting hardware that allows it to be mounted into a standard 48 cm equipment rack in either a single unit installation or a side-by-side ...

  • Page 4

    1-2 instrument overview ms27101a installation 1-2 pn: 10580-00409 rev. C ms2710xa ig connectors and chassis mounting hardware required tools the installation requires a medium size phillips screwdriver. 1. Power switch 2. Ethernet 3. Usb type a (2) 4. Rf input, n(f) 5. Reference input, bnc 6. Gps an...

  • Page 5: 1-3

    Ms27101a installation 1-3 single unit rack mounting ms2710xa ig pn: 10580-00409 rev. C 1-3 1-3 single unit rack mounting this section explains how to fit a single ms27101a monitor into an instrument rack using the two single mounting brackets. 1. Prepare the ms27101a by removing the front panel hand...

  • Page 6: 1-4

    1-4 side-by-side unit rack mounting ms27101a installation 1-4 pn: 10580-00409 rev. C ms2710xa ig 1-4 side-by-side unit rack mounting this section explains how to fit two ms27101a remote spectrum monitors into an instrument rack using the side-by-side mounting brackets. 1. Prepare both ms27101a instr...

  • Page 7: 2-1

    Ms2710xa ig pn: 10580-00409 rev. C 2-1 chapter 2 — ms27102a installation 2-1 introduction this chapter provides: • a brief overview of the ms27102a remote spectrum monitor • installation considerations and required equipment • considerations when selecting a location to install the remote spectrum m...

  • Page 8

    2-2 instrument overview ms27102a installation 2-2 pn: 10580-00409 rev. C ms2710xa ig connectors and chassis 1. Gps antenna, sma(f) 2. No connection 3. 3-pin power input (see “power supply gland assembly” on page 2-10 ) 4. Ethernet (see “ethernet gland assembly” on page 2-9 ) 5. Rf input port 2, n(f)...

  • Page 9

    Ms27102a installation 2-2 instrument overview ms2710xa ig pn: 10580-00409 rev. C 2-3 mounting hardware 1. Universal mounting bracket detail 2. Mounting bracket extensions and nuts (6 mm hex nuts, 2 each, used for wall mounting only) 3. Stainless machine screw set (10 mm m6 x 0.8, 4 each) 4. Stainles...

  • Page 10

    2-2 instrument overview ms27102a installation 2-4 pn: 10580-00409 rev. C ms2710xa ig connector glands the figure below illustrates the ip67 rated ethernet (top) and power connector (bottom) gland assemblies. Power supply the ms27102a remote spectrum monitor comes with an indoor ac/dc power converter...

  • Page 11: 2-3

    Ms27102a installation 2-3 surveying the installation site ms2710xa ig pn: 10580-00409 rev. C 2-5 2-3 surveying the installation site to ensure optimal performance of the ms27102a remote spectrum monitor, conduct a site survey to determine the optimal placement of the instrument for maximum range, co...

  • Page 12: 2-4

    2-4 required equipment ms27102a installation 2-6 pn: 10580-00409 rev. C ms2710xa ig 2-4 required equipment the following is required to install the ma27102a remote spectrum monitor: • #2 phillips screwdriver (for bracket to chassis and ground fasteners) • flat blade screwdriver (for strap clamps) • ...

  • Page 13: 2-6

    Ms27102a installation 2-6 pole and tower mounting instructions ms2710xa ig pn: 10580-00409 rev. C 2-7 2-6 pole and tower mounting instructions install the universal mounting bracket as instructed in section 2-5 . The bracket can accommodate mounting to a pipe diameter up to 101 mm (4 in). Refer to f...

  • Page 14: 2-7

    2-7 wall mounting instructions ms27102a installation 2-8 pn: 10580-00409 rev. C ms2710xa ig 2-7 wall mounting instructions the ma27102a universal mounting bracket can accommodate mounting to a variety of wall structures. The user is responsible for selecting the appropriate wall fasteners for the st...

  • Page 15: 2-8

    Ms27102a installation 2-8 installing the antenna cables ms2710xa ig pn: 10580-00409 rev. C 2-9 2-8 installing the antenna cables always install an antenna in accordance with local regulatory code and with best practices, and follow the mounting and installation instructions that were supplied with y...

  • Page 16

    2-10 installing the power supply cables ms27102a installation 2-10 pn: 10580-00409 rev. C ms2710xa ig 2-10 installing the power supply cables the ms27102a features an ip67 rated power connector. However, for the connection to be weatherproof, the weatherproofing gland must be installed around the co...

  • Page 17: 3-1

    Ms2710xa ig pn: 10580-00409 rev. C 3-1 chapter 3 — ms27103a installation 3-1 introduction the ms27103a remote spectrum monitor is configured with integral front panel handle and rack mounting bracket that allows it to be mounted into a standard 48 cm equipment rack. This chapter illustrates how to f...

  • Page 18

    3-2 instrument overview ms27103a installation 3-2 pn: 10580-00409 rev. C ms2710xa ig connectors and chassis required tools the installation requires a medium size phillips screwdriver. 1. Power led 2. Rf input ports, 12 or 24 sma(f) 3. Power input screw terminal (or 110 vac line connector with optio...

  • Page 19: 3-3

    Ms27103a installation 3-3 ms27103a rack mounting ms2710xa ig pn: 10580-00409 rev. C 3-3 3-3 ms27103a rack mounting this section illustrates how to fit a single monitor into an instrument rack. 1. Slide the instrument into the rack and secure with 4 screws as instructed by the cabinet manufacturer. F...

  • Page 20

    3-3 ms27103a rack mounting ms27103a installation 3-4 pn: 10580-00409 rev. C ms2710xa ig.

  • Page 22

    Anritsu company 490 jarvis drive morgan hill, ca 95037-2809 usa http://www.Anritsu.Com anritsu utilizes recycled paper and environmentally conscious inks and toner..