1. DL manuals
  2. Anritsu
  3. Adapter
  4. MZ1225A
  5. Operation Manual

Anritsu MZ1225A Operation Manual

Manual is about: Adapter for QSFP+

Summary of MZ1225A

  • Page 1

    Document no.: m-w3485ae-2.0 anritsu corporation mz1225a adapter for qsfp+ operation manual for safety and warning information, please read this manual before attempting to use the equipment. Keep this manual with the equipment. Second edition.

  • Page 2: Caution

    Ii safety symbols to prevent the risk of personal injury or loss related to equipment malfunction, anritsu corporation uses the following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the symbols before using the equipment. Some or all of t...

  • Page 3: Warning

    For safety iii warning always refer to the operation manual when working near locations at which the alert mark shown on the left is attached. If the advice in the operation manual is not followed there is a risk of personal injury or reduced equipment performance. The alert mark shown on the left m...

  • Page 4: Equipment Certificate

    Iv equipment certificate anritsu corporation certifies that this equipment was tested before shipment using calibrated measuring instruments with direct traceability to public testing organizations recognized by national research laboratories, including the national institute of advanced industrial ...

  • Page 5

    V crossed-out wheeled bin symbol equipment marked with the crossed-out wheeled bin symbol complies with council directive 2002/96/ec (the "weee directive") in european union. For products placed on the eu market after august 13, 2005, please contact your local anritsu representative at the end of th...

  • Page 6

    Vi notes on export management this product and its manuals may require an export license/approval by the government of the product's country of origin for re-export from your country. Before re-exporting the product or manuals, please contact us to confirm whether they are export-controlled items or...

  • Page 7: Ce Conformity Marking

    Vii ce conformity marking anritsu affixes the ce conformity marking on the following product(s) in accordance with the council directive 93/68/eec to indicate that they conform to the emc and lvd directive of the european union (eu). Ce marking 1. Product model model: mz1225a adapter for qsfp+ 2. Ap...

  • Page 8: C-Tick Conformity Marking

    Viii c-tick conformity marking anritsu affixes the c-tick marking on the following product(s) in accordance with the regulation to indicate that they conform to the emc framework of australia/new zealand. C-tick marking 1. Product model model: mz1225a adapter for qsfp+ 2. Applied directive and stand...

  • Page 9: About This Manual

    I about this manual the operation manual for the mz1225a adapter for qsfp+ covers the usage precautions, product outline and installation method. 1 product outline this section explains the purpose of this product usage. 2 before use this section explains the items and each part name confirmed when ...

  • Page 10: Table of Contents

    Ii. Table of contents for safety .................................................... Iii 1 outline ............................................ 1 2 before use...................................... 3 2.1 standard configuration.............................................. 3 2.2 applicable parts........

  • Page 11: 1 Outline

    1 outline 1 outline mz1225a adapter for qsfp+ is an adapter to convert the qsfp+ module to the cfp module form. The mz1225a is used being inserted to the measurement port (cfp module installation part) of the md1260a 40/100g ethernet analyzer (hereinafter referred to as md1260a). Qsfp+: quad small f...

  • Page 12

    1 outline qsfp+ register tx1 tx2 tx3 tx4 rx1 rx2 rx3 rx4 scl sda mz1225a logic circuit qsfp+ connector tx1 tx2 tx3 tx4 tx5 tx6 tx7 tx8 tx9 tx10 rx1 rx2 rx3 rx4 rx5 rx6 rx7 rx8 rx9 rx10 cfp connector optical connector scl: 2-wire serial interface clock sda: 2-wire serial interface data mdio bus addre...

  • Page 13: 2 Before

    2 before use 2 before use 2.1 standard configuration at unpacking, check that all items are included. See the attached file including the standard configuration table (see table 2.1-1). Contact your anritsu service and sales office or agent if any parts are missing or damaged. Table 2.1-1 standard c...

  • Page 14: How to Use

    3 how to use 4 3 how to use this section explains how to use the mz1225a. 3.1 connection precautions to use the mz1225a properly, you must keep the connection precautions written below: 1. The insert/remove cycles of the cfp connector are about 180. Even though the insert/remove cycles are repeated,...

  • Page 15

    3 how to use how to remove the qsfp+ module 1. Remove the module when the optical connector is attached. 2. Move the lever of the qsfp+ module down. 3. Hold both sides of the qsfp+ module between the tips of your first two fingers. 4. Pull out the qsfp+ module. Mz1225a lever figure 3.2-1 how to remo...

  • Page 16: Caution

    3 how to use how to install the mz1225a in md1260a caution some devices installed in the mz1225a and md1260a may be damaged by impressed static electricity and short circuit. As a countermeasure against static electricity, the operator should wear an electrostatic discharge wrist strap. Make sure th...

  • Page 17

    3 how to use mz1225a emi gasket strap figure 3.2-2 countermeasure against static electricity 7.

  • Page 18: 3.3

    3 how to use 3.3 display on md 1260a for the md1260a operation method, refer to the md1260a 40/100g ethernet analyzer operation manual. When connecting the qsfp+ module to the md1260a using the mz1225a, the following items are displayed on the opt. Tab. Table 3.3-1 items displayed on opt tab item ex...

  • Page 19: 3.4

    3 how to use 9 3.4 remote control for md1260a display items for the md1260a remote operation method, refer to the md1260a 40/100g ethernet analyzer operation manual (remote control). The items displayed on the md1260a opt tab when using the mz1225a can be read out by the calclate:data command. The i...

  • Page 20: 4 Storage

    4 storage precautions 10 4 storage precautions remove the qsfp+ module from the mz1225a before storing this device. Wipe dust, fingerprints, stains, spots, etc., from the surface of the mz1225a before storing it. Wrap the mz1225a in plastic or a similar material to protect against dust. Avoid storin...

  • Page 21: 5 Transporting

    5 transporting and disposal 11 5 transporting and disposal the following describes precautions for transporting and disposing of the mz1225a. Repackaging repack the mz1225a min the packing material (box) in which it was delivered. If the packing material has been thrown away or damaged, repack the m...

  • Page 22

    5 transporting and disposal 12..

  • Page 23: A.1  Adapter For Qsfp+

    Appendix a specifications a-1 a.1 adapter for qsfp+ table a-1 specifications for mz1225a qsfp+ adapter item specifications configuration – mainframe – mz1225a adapter for qsfp+ – applicable parts – z1442a md1260a software/manual cd-rom interface specification to be complied with cfp msa hardware spe...

  • Page 24: A.2 Qsfp+ Module

    Appendix a specifications a.2 qsfp+ module table a.2-1 specifications for qsfp+ 40gbase-sr4 item specifications modelname g0296a number of fibers 4 conformable fiber multi-mode fiber (50/125μm) rate per lane 10.3125 gbd ±100ppm optical connector mpo laser safety class1m (iec60825-1, 21 cfr 1040.10 l...

  • Page 25

    A.2 qsfp+ module a-3 table a.2-1 specifications for qsfp+ 40gbase-sr4 (cont'd) item specifications reception part *3 wavelength 840 to 860 nm peak received light level per lane 4 dbm maximum averaged received light level per lane –2.4 dbm received light level per lane (oma) 3 dbm reflectance of re...

  • Page 26

    Appendix a specifications a-4..