- DL manuals
- ANTAIRA
- Media Converter
- BTS-1000A
- Operation Manual
ANTAIRA BTS-1000A Operation Manual
Summary of BTS-1000A
Page 1
Bts-1000a bluetooth to rs-232 converter operation manual version 1.0
Page 2: Table Of Contents
1 table of contents 1. Introduction ……………………………………………………………….. 2 2. Package checklist ………………………………………………………….. 3 3. Product specification …………………………………………………... 4 4. Product panel view description ……………………………………. 5 bts-1000a product view …………………………………………………… 5 dc-in power outlet ……………………………………………………...
Page 3: Introduction
2 1 1 introduction thank you for purchasing the bts-1000a bluetooth to serial adapter. The bts-1000a replaces standard rs-232 cables by utilizing bluetooth wireless technology. The bts-1000a uses standard rs-232 interface, so it can be easily adapted for industrial machines with rs-232 connection. T...
Page 4: Package Checklist
3 2 2 package checklist the bts-1000a is shipped with the following items: 1 x bts-1000a bluetooth to rs-232 adapter with antenna 1 x power adapter (5v dc, 200ma) quick installation guide setup utility software cd note: notify your sales representative if any of the above items are missing o...
Page 5: Product Specification
4 3 3 product specification serial port no. Of ports: rs-232 * 1 port ● port type: db-9 female ● speed: 1200 bps ~ 115.2k bps ● parity: none , odd , even ● data bit: 8 ● stop bit: 1 , 2 ● flow control: dtr / dsr ● rs-232 signals: rx , tx , gnd , rts , cts , dtr , dsr bluetooth i/o port no. Of po...
Page 6: Bts-1000A Product View
5 4 4 product panel view description bts-1000a product view dc-in power outlet the bts-1000a bluetooth to serial adapter is powered by a single 5v dc (inner positive / outer negative) power supply and 200ma of current. A suitable power supply adapter is included in the packaging. Connect the power l...
Page 7
6 antenna connector the antenna connector is a standard reverse sma jack. The 2.0 dbi dipole antenna has 50 ohms impedance and can support 2.4ghz frequency. (the antenna is changeable for higher gain antennas) serial i/o port of rs-232 connect the serial i/o rs-232 connector into devices like comput...
Page 8
7 led indicators red color led ： power indicator (when the power is on, the red color led stay lit. Green color led ： before connecting to synchronize between the device and the bt rs232 config tool software, the green led will be blinking. After connecting to synchronize between the device and the ...
Page 9
8 5 5 bts-1000a hardware installation 1. Connect the bts-1000a bluetooth adapter to a com port of a pc and then connect the dc power adapter jack into a power outlet and dc-in outlet. You will see the red led turn on and the green led will blink. 2. After running the bt rs232 config tool and finishi...
Page 10: Tool Installation
9 6 6 bt rs232 config tool installation & setup when setting up the bts-1000a adapter for the first time, you have to install and run the bt rs232 config tool (bt1.Exe) first in your computer device. The utility cd is enclosed in the packaging. Before you use the bts-1000a adapter, you have to pair ...
Page 11
10 bt rs232 config tool parameter configuration running the bt rs232 config tool, the configuration screen will pop-up as depicted above. A. Com port select a com port number, you have to avoid the ports that conflict with other devices in your computer and only use available ports. B. Device name...
Page 12
11 e. Pin code the pin code is used for security like a pass key. The device uses this “pin code” to identify itself when connecting and establishing communication. F. Role the role is used to identify the role of the device as either a master or slave. When the “role” is set to “master”, the device...
Page 13: Apply “Connect”
12 apply “connect” after configuring the parameters, click the “connect” button while immediately pressing the sync button located on the left side of the device. On the following screen, the “connect” button should change to “disconnect.” the “read” and “write” button will now be active on the bott...
Page 14
13 apply “write” clicking “write” will save all parameters configured using the bt rs232 config tool. Apply “read” clicking “read” will load all parameters saved previously. The local address will be updated from the real device address initially..
Page 15: Pin Outs And Connector
14 a a p p p p e e n n d d i i x x a a pin outs and connector □ □ □ dc power outlet □ □ □ rs-232 pin assignment the pin assignment scheme for a 9-pin male connector on a dte is provided below. Pin 1: x pin 2: txd pin 3: rxd pin 4: dsr pin 5: gnd pin 6: dtr pin 7: cts pin 8: rts pin 9: dc 5v □ □ □ rs...