ANTAIRA FCU-1802Px User Manual

Manual is about: 100Base-FX to 10/100Base-TX PoE Media Converter

Summary of FCU-1802Px

  • Page 1

    100base-fx to 10/100base-tx poe media converter fcu-1802px user’s manual.

  • Page 2: Trademarks

    Trademarks copyright © antaira technologies 2013. Contents subject to revision without prior notice. Antaira is a registered trademark of antaira technologies. The information in this manual is subject to change without notice. All other trademarks belongs to their respective owners. Disclaimer anta...

  • Page 3: Fcc Warning

    Fcc warning this equipment has been tested and found to comply with the regulations for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. ...

  • Page 4: Weee Warning

    Weee warning to avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dis...

  • Page 5: Table Of Contents

    Table of contents 1. Overview ......................................................................... 6 2. Model list ........................................................................ 7 3. Checklist .......................................................................... 7 4. Product outl...

  • Page 6: 1. Overview

    6 1. Overview thank you for purchasing antaira's fcu-1802px family of 10/100mbps ethernet twisted pair to 100base-fx fiber-optic poe bridge converter. This converter is used to convert one type media signal to another easily, efficiently and inexpensively. The converter provides power over ethernet ...

  • Page 7: 2. Checklist

    7 2. Checklist your fcu-1802px package should contain the following items: ● 100base-fx to 10/100base-tx poe media converter x 1 ● ac-dc power adapter (input: 48v dc, 0.4a max.) x 1 ● user’s manual x 1 if any items are missing or damaged, please consult the dealer from which you purchased your poe m...

  • Page 8: 3. Product Outlook

    8 3. Product outlook overview layout of the fcu-1802px. Bottom rear panel top panel front panel 48v dc off lfp on.

  • Page 9: Left View

    9 left view there are one rj-45 twisted-pair jack (auto-mdi/mdi-x), one fiber-optic connector (vary by model) and four led indicators. Pwr tx rx fx tp poe in use 10/100base-tx poe media converter 10/100base-tx to 100base-fx lnk/ act right view one dip switch for link fault pass through (lfp) feature...

  • Page 10

    10 4. Link fault pass through (lfp) the lfp function includes the link fault pass through function (llcf/llr) and the dip switch design. Llcf/llr can immediately alert administrators about problems with the link media and provide an efficient solution to monitor the net. The dip switch can disable o...

  • Page 11: Link Loss Return (Llr)

    11 station. The administrator can then determine the source of the problem. Media converter management station switch/hub w/snmp management station media converter switch/hub w/snmp tp tp fiber cable lfp on lfp on l led lit = established link ° led unlit = no link media converter management station ...

  • Page 12

    12 if one of the optical conductors is bad (as shown in the diagram box below), the converter with llr function will return a no-link condition to its link partner. With llcf function also enabled, the no-link condition is carried forward to the switch/hub where a trap is generated to the management...

  • Page 13: Fcu-1802Px

    13 5. Installing the converter please follow these steps to install the poe media converter: ● turn off the power of the device/station on the network to which the fcu-1802px will be attached. ● ensure that there is no activity in the network. ● attach fiber cable from the fcu-1802px to the fiber ne...

  • Page 14: 6. Poe Function

    14 6. Poe function fcu-1802px and the ieee 802.3af injector / splitter equipment installation: before your installation, it is recommended to check your network environment. If there is any ieee 802.3af devices that need to power on, the fcu-1802px can provide a way to supply power for this ethernet...

  • Page 15: 7. Led Indication

    15 7. Led indication • system led color function pwr green lit: indicate the device is powered. • 10/100base-tx port led color function lnk/act green blink indicate that the media converter is actively sending or receiving data over that port. Lit indicate that the port is link up. Off indicate that...

  • Page 16

    16 8. Cable connection parameter the limitations are as below: duplex connection limitation (max.) twisted pair half / full node to node node to switch/hub 100 meters multi-mode converters mm half node to node node to switch 412 meters mm full node to node node to switch 2 kilometers single-mode con...

  • Page 17

    17 9. Fcu-1802px technical specifications the fcu-1802px comes with the following standard features: ● standard: ieee 802.3u, 10/100base-tx ,100base-fx ieee 802.3af power over ethernet ● connectors: • one rj-45 (auto-mdi/mdi-x) twisted pair, eia568 with poe • one fiber-optic, 1310nm wavelength, conn...

  • Page 18: Appendix A

    18 appendix a a.1 device's rj-45 pin assignments • 10/100mbps, 10/100base-tx contact mdi mdi-x 1 1 (tx +) 3 2 2 (tx -) 6 3 3 (rx +) 1 6 6 (rx -) 2 4, 5, 7, 8 not used not used implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly for...

  • Page 19

    19 figure a-1: straight-through and crossover cable please make sure your connected cables are with the same pin assignment and color as the above picture before deploying the cables into your network. A.3 fiber optical cable connection parameter the wiring details are as below: • fiber optical patc...

  • Page 20

    This page is intentionally left blank.