1. DL manuals
  2. ANTAIRA
  3. Switch
  4. LMP-0800G-24
  5. User Manual

ANTAIRA LMP-0800G-24 User Manual

Manual is about: 8-Port Industrial PoE+ Gigabit Managed Ethernet Switches

Summary of LMP-0800G-24

  • Page 1

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 i lmp-0800g-24 series 8-port industrial poe+ gigabit managed ethernet switches 8*10/100/1000tx (30w/port); 12~36vdc power input (w/ voltage booster) version 1.0 user manual.

  • Page 2

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 ii © copyright 2015 antaira technologies, llc all rights reserved this document contains information, which is protected by copyright. Reproduction, adaptation or translation without prior permission is prohibit...

  • Page 3

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 iii fcc warning this equipment has been tested and found to comply with the limits for a class-a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection a...

  • Page 4: Table Of Contents

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 iv table of contents 1. Introduction ................................................................. 1 1.1 product overview 1 1.2 product software features 1 1.3 product hardware features 2 1.4 package content...

  • Page 5

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 v 5.2.1 system information ................................................ 15 5.2.2 admin & password ................................................. 16 5.2.3 ip setting ..........................................

  • Page 6

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 vi 5.6.4 msti configuration ................................................ 37 5.7 igmp snooping 40 5.7.1 igmp settings ........................................................ 40 5.7.2 igmp snooping status tab...

  • Page 7

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 vii 5.14 802.1x 57 5.14.1 802.1x settings .................................................... 57 5.14.2 local database .................................................... 58 5.14.3 radius server .................

  • Page 8

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 viii 5.20 configuration 73 5.20.1 save ..................................................................... 74 5.20.2 backup & restore ................................................ 74 5.20.3 auto load & back...

  • Page 9: 1. Introduction

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 1 1. Introduction all antaira industrial managed switches come with a pre- installed “user-friendly” web console interface, which allows users to easily configure and manage the units, whether one is using a ser...

  • Page 10

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 2 ieee802.1q vlan tagging, port-based vlan support igmp snooping v1/v2, igmp filtering / throttling, igmp query up to 256 group supports ipv4/ipv6, rmon, mib ii, port mirroring, event syslog, dns, ntp/sntp, http...

  • Page 11: 1.4 Package Contents

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 3 1.4 package contents 1 – lmp-0800g-24 series: 8-port industrial gigabit poe+ managed ethernet switch, with 8*10/100/1000tx (pse 30w/port) 1-product cd 2-wall mounting brackets and screws 1-rj45 to db9 serial c...

  • Page 12: 2. Hardware Description

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 4 2. Hardware description 2.1 physical dimensions figure 2.1, below, shows the physical dimensions of antaira ’s lmp-0800g-24 series: 8-port industrial gigabit poe+ managed ethernet switches with 8*10/100/1000tx...

  • Page 13: 2.2 Front Panel

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 5 2.2 front panel the front panel of the lmp-0800g-24 series industrial gigabit poe+ managed ethernet switch is shown below in figure 2.2. 2.3 top view figure 2.3, below, shows the top panel of the lmp-0800g ser...

  • Page 14: 2.5 Reset Button

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 6 led color description p1 green on power input 1 is active off power input 1 is inactive p2 green on power input 2 is active off power input 2 is inactive fault green / red green power input 1 or 2 is inactive ...

  • Page 15: 2.6 Ethernet Ports

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 7 2.6 ethernet ports rj-45 ports rj-45 ports (auto mdi/mdix): the rj-45 ports are auto-sensing for 10base-t, 100base-tx, or 1000base-t connections. Auto mdi means that the switch can connect to another switch or...

  • Page 16: 2.7 Cabling

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 8 the following figures show the cabling schematics for straight-through and crossover. 2.7 cabling use the four twisted-pair, category 5e, or the above cabling for the rj-45 port connections. The cable between ...

  • Page 17

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 9 2.9 wiring the fault alarm contact the fault alarm contact is in the middle of the terminal block connector as the picture shows below in figure 2.8. By inserting the wires, it will detect the fault status inc...

  • Page 18: 3. Mounting Installation

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 10 3. Mounting installation 3.1 din-rail mounting the din-rail is pre-installed on the industrial ethernet switch from the factory. If the din-rail is not on the industrial ethernet switch, please see figure 3.1...

  • Page 19: 3.2 Wall Mounting

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 11 3.2 wall mounting follow the steps below to mount the industrial ethernet switch using the wall mounting bracket as shown below in figure 3.4. 1. Remove the din-rail bracket from the industrial ethernet switc...

  • Page 20: 4. Hardware Installation

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 12 4. Hardware installation 4.1 installation steps this section will explain how to install antaira ’s lmp-0800g-24 series: 8-port industrial gigabit poe+ managed ethernet switches with 8*10/100/1000tx (pse: 30w...

  • Page 21: 5. Web Management

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 13 5. Web management 5.1 web console configuration this section introduces the configuration by web browser. 5.1.1 about web-based management all of antaira’s industrial managed switches are embedded with html w...

  • Page 22

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 14 figure 5.2 - web console main (status) page 3. The login screen appears. 4. Key in the default username: admin and password admin. 5. Click “login” button, then the main (status) page of the web console will ...

  • Page 23: 5.2 Basic Setting

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 15 5.2 basic setting 5.2.1 system information below, figure 5.3, shows the switch system setting information. Terms value description system name factory default: switch *users can assign any name label to ident...

  • Page 24: 5.2.2 Admin & Password

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 16 5.2.2 admin & password below, describes how to configure the system user name and password for the web console login. Terms value description new password users can assign a new password and the maximum lengt...

  • Page 25: 5.2.4 Ipv6 Neighbor Cache

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 17 terms value description dhcp client enable the dhcp client by checking this box. If dhcp fails and the configured ip address is zero, dhcp will retry. If dhcp fails and the configured ip address is non-zero, ...

  • Page 26: 5.2.5 Ipv6 Settings

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 18 5.2.5 ipv6 settings terms value description ipv6 enable/disable check or uncheck the box to enable or disable ipv6 settings ipv6 address the unit default ipv6 address is depended on mac address. Assign the ip...

  • Page 27: 5.3 Port Management

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 19 terms value description local time users can define the switch’s local time, or click “sync with browser” button to have local time setup automatically. Select your time zone users can use dropdown box to set...

  • Page 28: 5.4.1 Poe Configuration

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 20 terms value description port no. It shows each port status: up for link active, and down for link inactive. Port name users can create or insert a value or label for each port’s identification. The maximum le...

  • Page 29: 5.4.2 Ping Alarm

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 21 terms value description port no. Poe port number status any poe port will automatically detect any pd (powered device) is connected and display the situation. Mode users can use the dropdown box to enable or ...

  • Page 30: 5.5 Erps

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 22 5.5 erps in any industrial automation application, designing redundant ring network paths to protect networks from unexpected failovers is extremely important in mission-critical networks because they need to...

  • Page 31: 5.5.1 Erps Status

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 23 ethernet ring protection switching (erps), defined in itu-t g8032, implements a protection switching mechanism for ethernet traffic in a ring topology. By performing the erps function, potential loops in a ne...

  • Page 32: 5.5.2 Erps Configuration

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 24 terms value description ring state abnormal: after enabling erps, one of erps node link failed or link down. Normal: erps disable or after enabling erps, the ring is closed and working well. Node state initia...

  • Page 33

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 25 terms value description protocol “enable” or “disable” erps protocol ring port 0 erps ring port 0, it could be map to real switch port 1 – port 6. Do not set the same as ring port 1. Ring port 1 erps ring por...

  • Page 34

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 26 5.5.3 before configuring erps before configuring erps, the rapid spanning tree protocol (rstp), or multiple spanning tree protocol is required to disabled, due to only one protocol is exclusive running within...

  • Page 35

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 27 step 4: press the apply button in the lower right corner as shown below in figure 5.26. Ethernet ring protection switch (erps) is an ethernet ring protection protocol which is used to prevent forming the loop...

  • Page 36

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 28 5.5.3.1 scenario a – rpl configured architecture under scenario a, there are three major roles required to configure within the erps configuration. Figure 5.27 – rpl-configured architecture caution: before en...

  • Page 37

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 29 [rpl owner node] there is only one rpl owner node could be set in a ring network. In order to set up the rpl owner node, choose a switch and enable “protocol” under the erps configuration interface, and follo...

  • Page 38

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 30 [rpl neighbor node] users should choose a second managed switch that is adjacent to the first managed switch and set it up as the rpl neighbor node. For configuration, users should login to the second managed...

  • Page 39

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 31 [none node] then users should setup the rest of the managed switches’ “role” of both “ring port 0 and 1” as “none node” as shown above in figure 5.27. Please be sure no duplicate port number has been chosen w...

  • Page 40

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 32 5.5.3.2 scenario b – non-configured architecture in some situations, users can choose not to configure the rpl owner and neighbor node. The erps can still work well under the mechanism by blocking one of the ...

  • Page 41

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 33 after the configurations, press the “apply” button on the bottom right corner to save the settings. . Figure 5.32 – non-configured architecture setup example.

  • Page 42: 5.6 Spanning Tree

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 34 5.6 spanning tree the spanning tree protocol (stp), defined in the ieee standard 802.1d, can be created within a mesh network of connected layer-2 switches. The rapid spanning tree protocol (rstp), defined in...

  • Page 43: 5.6.2 Rstp Configuration

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 35 5.6.2 rstp configuration users can enable/disable the rstp function, and set the parameters for each port. Terms value description mode users can select rstp or mstp function to be enabled or disabled before ...

  • Page 44

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 36 path cost for the other switch from this transmitting switch at the specified port. When path cost insert in 0, the switches will be setup as automatic data transmitting. Priority (0~240) enter a number 0 thr...

  • Page 45: 5.6.3 Msti Status

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 37 5.6.3 msti status users can display the msti root status and port status by selecting the instance id number from 1 to 15 by clicking on the dropdown box from the “msti status” interface. 5.6.4 msti configura...

  • Page 46

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 38 terms value description mtsi configuration name users can insert the unique mac address of the bridge switch. Revision users can insert the value from 0~65535 mtsi instance instance no. & vlan group there are...

  • Page 47

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 39 terms value description instance tabs users can select instance tab #1~#15 to configure each msti port “cost” & “priority” value. Cost users can define the path cost value from 1 through 200000000 to the othe...

  • Page 48: 5.7    Igmp Snooping

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 40 5.7 igmp snooping the internet group management protocol (igmp) is a communications protocol used to manage the membership of internet protocol multicast groups. Igmp is used by ip hosts and adjacent multicas...

  • Page 49: 5.8 802.1Q Vlan

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 41 5.7.2 igmp snooping status table multicast filtering is the system by which end stations only receive multicast traffic if they register to join specific multicast groups. With multicast filtering, network de...

  • Page 50

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 42 all antaira’s industrial managed switches support 802.1q vlan. Tagged-based vlan is an ieee 802.1q specification standard, and it is possible to create a vlan across devices from different switch venders. Iee...

  • Page 51

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 43 terms value description management vlan id set the vlan id of management vlan. Users have to configure other settings done, and configure this field finally. 802.1q vlan id the id of this vlan. Vlans that hav...

  • Page 52: 5.9.1 Qos Classification

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 44 5.9.1 qos classification terms value description queue scheduling users can set it as “weighted” or “strict” weighted mode: an 8, 4, 2, 1 weighting is applied to each round robin priority queue. Strict mode: ...

  • Page 53: 5.9.2 Cos Mapping

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 45 default cost users can set each port’s priority queue from 0 to 7 by clicking from dropdown box; of which 0 is the highest, and 7 is the lowest click the “apply” button to save changes. 5.9.2 cos mapping term...

  • Page 54: 5.10 Port Trunk

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 46 5.10 port trunk port trunk, also called “link aggregation”, is a method of combining multiple network connections in parallel. It is to increase throughput beyond what a single connection could sustain. For e...

  • Page 55: 5.10.1 Trunk Status

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 47 5.10.1 trunk status the below graph is the port trunk status. The below table describes the term and value description of “port trunk”. Terms value description aggregation show the status of port trunk. List ...

  • Page 56: 5.11 Port Mirroring

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 48 the below table describes the field of the terms and value descriptions of “port trunk”. 5.11 port mirroring enable or disable mirroring feature. When enabled, a copy of matched frames will be mirrored to the...

  • Page 57: 5.12 Snmp

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 49 5.12 snmp simple network management protocol (snmp) is the protocol developed to manage nodes (servers, workstations, routers, switches and hubs etc.) on an ip network. Snmp enables network administrators to ...

  • Page 58

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 50 snmp general - terms value description snmp version all antaira managed switches support snmp v1, v2c, and v3 server. Users can enable all snmp server v1, v2c and v3, or enable only v1 and v2c, or enable only...

  • Page 59: 5.12.2 Snmp Trap Setting

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 51 user auth type the method used to encrypt the passphrase auth passphrase “auth passphrase” is a string used to authenticate (user). The range of length is from 8 to 32 characters with only numeric and alphabe...

  • Page 60: 5.13 Dhcp Server / Rely

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 52 inform timeout the trap message will be s ent after “inform timeout” expired. This field works only when “trap mode” is set to “inform”. Trap destination ip the destination ip that trap message will be sent t...

  • Page 61

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 53 field description vlan the management vlan id. Always vlan 1. Module the stack number. Always 0 here. Port it is the incoming port number from dhcp client, and the port number is started by 1. Field descripti...

  • Page 62: 5.13.1  Dhcp Client

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 54 5.13.1 dhcp client the below figure is the ip setting of dhcp client. The below table describes the field of the dhcp client terms and value descriptions. Terms value description dhcp client “enable” or “disa...

  • Page 63

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 55 the below table describes the field of the dhcp server terms and value description. Terms value description server status dhcp server status, it shows “down” when “disable”, and it shows “up” when “enable”. E...

  • Page 64: 5.13.4 Dhcp Relay

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 56 5.13.4 dhcp relay dhcp relay terms value description enable “enable” or “disable” dhcp relay agent relay option 82 “enable” or “disable” dhcp relay option 82 relay to server1 the ip address of the first dhcp ...

  • Page 65: 5.14 802.1X

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 57 5.14 802.1x 802.1x is an ieee standard for port-based network access control. It provides an authentication mechanism to devices that wish to attach to a lan or wlan. This port-based network access control pr...

  • Page 66: 5.14.2 Local Database

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 58 the below tables describes 802.1x terms and value description. 802.1x terms value description 802.1x enable check the checkbox to enable “802.1x” protocol. Server type “local” for authenticating with local se...

  • Page 67: 5.14.3 Radius Server

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 59 the below table describes local database terms and value description. Terms value description user name the user name use to authenticate in 802.1x when server set to “local”. Password the password use to aut...

  • Page 68: 5.15 Upnp

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 60 5.15 upnp universal plug and play (upnp) is a set of networking protocols that were promoted by the upnp forum. Upnp protocol permits networked devices to discover each other's presence on the network and sea...

  • Page 69: 5.16 Modbus Tcp

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 61 5.16 modbus tcp modbus is a serial communications protocol that is used with industrial automation equipment, such as programmable logic controllers (plcs), sensors, and meters. It is a common, simple, and ro...

  • Page 70

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 62 5.16.2 modbus data map and information the data map addresses for antaira’s switches are shown in the table for function code 6. Address offset data type interpretation description system information 0x0000 t...

  • Page 71

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 63 0x0030 20 words ascii product name = “lmp-0800g-24” word 0 hi byte = ‘l’ word 0 lo byte = ‘m’ word 1 hi byte = ‘p’ word 1 lo byte = ‘-’ word 2 hi byte = ‘0’ word 2 lo byte = ‘6’ word 3 hi byte = ‘0’ word 3 lo...

  • Page 72

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 64 0x0001 : on 0x005a 1 word hex fault led status 0x0000 : boot error 0x0001 : normal 0x0002 : fault 0x0082 1 word hex do1 0x0001 : normal 0x0002 : fault port information 0x1000 to 0x1005 1 word hex port 1 to 6 ...

  • Page 73

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 65 0x1400 to 0x1413 (port 1) 0x1414 to 0x1427 (port 2) 20 words ascii port 1 to 6 name port name = “100fdx,rj45.” word 0 hi byte = ‘1’ word 0 lo byte = ‘0’ word 1 hi byte = ‘0’ word 1 lo byte = ‘f’ … word 5 hi b...

  • Page 74

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 66 word 0 = 0 x 1324 word 1 = 0 x 4800 0x2200 to 0x220b 2 words hex port 1 to 6 tx error packets ex : port 1 tx error packet amount = 13244800 received modbus response : 0x13244800 word 0 = 0 x 1324 word 1 = 0 x...

  • Page 75

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 67 0xffff : erps not enable 0x0000 : normal 0x0001 : neighbor 0x0002 : rpl owner 0x3301 1 word hex erps port1 role 0xffff : erps not enable 0x0000 : normal 0x0001 : neighbor 0x0002 : rpl owner 0x3302 1 word hex ...

  • Page 76: 5.17 System Warning

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 68 5.17 system warning system warning function is very important for managing a switch. Users can manage the switch by “syslog”, “system event log”, and “email server” setup for advanced notice in any event type...

  • Page 77: 5.17.2 System Event Log

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 69 5.17.2 system event log users can view and display the system event log by clicking the “apply” button on the right bottom corner of the interface. Then, the system event logs will display within the syslog l...

  • Page 78: 5.17.4 Event Selection

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 70 terms value description e-mail alert enable/disable transmission system warning events by e-mail. Smtp server address setting up the mail server ip address sender e-mail address set up the email account to se...

  • Page 79: 5.17.5 Fault Alarm

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 71 5.17.5 fault alarm when any selected fault event has occurred, the fault led of the switch’s front panel will light up and the electric relay will signal at the same time. Users can check the checkbox of any ...

  • Page 80: 5.19 Maintenance

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 72 5.18.2 mac table configuration users can check the checked box of each port and insert the port’s vid and mac address of the device that is connected to that port, then click the “add” button to continue addi...

  • Page 81: 5.19.2 Reboot

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 73 5.19.2 reboot users can click the “apply” button under the “reboot” interface to reboot the switch. 5.19.3 default users can reset the switch to “factory default” by clicking the “apply” button under the defa...

  • Page 82: 5.20.1 Save

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 74 5.20.1 save users can click the “save” button under the “save configuration” interface, once all the settings had been configured. 5.20.2 backup & restore terms value description configuration managemnet back...

  • Page 83: 5.21 Logout

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 75 5.20.3 auto load & backup 5.20.1 terms value description usb auto load select usb auto load (plug usb stick and reboot the switch), it will auto load startup file from usb to switch. Please make sure the star...

  • Page 84: 6.1 About Cli Management

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 76 6. Command line interface management 6.1 about cli management besides web-based management, lmp-0800g-24 series also supports cli management. Users can use console or telnet to management switch by cli. Cli m...

  • Page 85

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 77 step 2: input a name for the new connection. Step 3: select to use a specific com port number..

  • Page 86

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 78 step 4: the com port property settings are as follows: 115200 for “bits per second”, 8 for “data bits”, none for parity, 1 for “stop bits” and none for “flow control”. Step 5: the console login screen will ap...

  • Page 87

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 79 follow the steps below to access the console via telnet. Step 1: telnet to the ip address of the switch from the windows “run” command as below. Step 2: the login screen will appear. Use the keyboard to enter...

  • Page 88

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 80 commander groups group command mode system hostname [switch] configure no hostname configure system location [none] configure system contact [none] configure no system location configure no system contact con...

  • Page 91

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 83 no schedule [monday~sunday] starttime interface no schedule [monday~sunday] endtime interface show power inline status interface show keepalive ip interface show keepalive time interface show schedule [monday...

  • Page 92

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 84 show spanning-tree max-age configure show spanning-tree cost interface show spanning-tree port-priority interface show spanning-tree link-type interface show spanning-tree auto-edge interface show spanning-tr...

  • Page 93

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 85 no event smtp warm-start configure no event smtp authentication-failure configure no event smtp erps-change configure no event smtp interface [interface_name] up configure no event smtp interface [interface_n...

  • Page 94

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 86 show event syslog interface [interface_name] up configure show event syslog interface [interface_name] down configure event alarm power1 enable configure event alarm power2 enable configure event alarm interf...

  • Page 98

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 90 dhcp server name-server [dns_ip] configure dhcp server lease [dhcp_lease_time] configure dhcp server binding [bind_num][mac] [bind_ip] configure dhcp server port-binding [port] [bind_ip] configure dhcp servic...

  • Page 99

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 91 no upnp advertisement interval configure show upnp enable configure show upnp advertisement interval configure modbus modbus tcp server configure no modbus tcp server configure show modbus tcp server configur...

  • Page 100

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 92 show dot1x authentication server 2 ip configure show dot1x authentication server 2 port configure show dot1x authentication server 2 share-key configure show dot1x local-db [user] [password] configure show do...

  • Page 101

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 93 fill in the folder and filename behind the “copy running-config usb” command. Ex: file1, / folder /file2. 2. Cli : enable -> configure terminal ->copy startup-config usb (path) fill in the folder and filename...

  • Page 102

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 94 upgrade via tftp cli : enable -> configure terminal ->tftp server ip [ip_address] ->tftp file name [upgrade_file_name] ->tftp upgrade fill in the tftp server ip and upgrade file name behind the “tftp server i...

  • Page 103: 7. Technical Specifications

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 95 7. Technical specifications table 7.1 has the technical specifications for antaira ’s lmp-0800g-24 series: 8-port industrial gigabit poe+ managed ethernet switch with 8*10/100/1000tx (pse: 30w/port) ports. St...

  • Page 104

    Antaira technologies - industrial ethernet switches lmp-0800g-24 series user manual v1.0 96 protection overload current present power reverse polarity present cpu watch dog present network cable 10base-t: 2-pair utp/stp cat. 3, 4, 5 cable; 100base-tx: 2- pair utp/stp cat. 5 cable. Eia/tia-568 100-oh...