1. DL manuals
  2. ANTAIRA
  3. Switch
  4. LNP-0500 series
  5. User manual

ANTAIRA LNP-0500 series User manual

Manual is about: 6-port Industrial Unmanaged Ethernet Switches 4*10/100Tx + 2*100Fx

Summary of LNP-0500 series

  • Page 1

    Lnx-0602 series 6-port industrial unmanaged ethernet switches 4*10/100tx + 2*100fx user manual.

  • Page 2: Fcc Warning

    Fcc warning this equipment has been tested and found to comply with the limits for a class-a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, an...

  • Page 3: Content

    Content introduction ................................................................ 1 features ................................................................... 1 package contents .................................................... 2 hardware description ...........................................

  • Page 4: Introduction

    1 introduction antaira’s lnx-0602 series switches are smart 6-port industrial unmanaged ethernet switches supporting 4-port 10/100tx fast ethernet and 2-port 100fx of sc or st type connector and support multi-mode in 2km, or single-mode in 30km. The lnx-0602 series switches support 12~48vdc power in...

  • Page 5: Package Contents

    2 package contents please refer to the package contents list below.  lnx-0602 series - 6-port industrial unmanaged switch with fiber w/din rail bracket  user manual  removable terminal block  wall-mount kit (2 wall-mount plates with screws) compare the contents of the industrial switch with the ...

  • Page 6: Hardware Description

    3 hardware description the industrial switch ’s hardware spec, port, cabling information, and wiring installation will be described. Physical dimension the lnx-0602 series - 6-port industrial unmanaged ethernet switch with fiber dimension: (w x d x h) is 30mm x 99mm x 142mm.

  • Page 7: Front Panel

    4 front panel the front panel of the industrial switch is shown below: front panel of the industrial switch top view the top view of the industrial switch has one terminal block connector of two dc power inputs and relay circuit contact. Top view of the industrial switch.

  • Page 8: Led Indicators

    5 led indicators the diagnostic leds located on the front panel of the industrial switch provide real-time information of the system and optional status. The following table provides the description of the led status. Led color description p1 green on power input 1 is active off power input 1 is ina...

  • Page 9: Ports

    6 ports  rj-45 ports the (rj-45) fast ethernet ports will auto-sense for 10base-t or 100base-tx connections. Auto mdi/mdix means that the switch can connect to another switch or workstation without changing straight through or crossover cabling. Please refer to the table below for rj-45 pin assignm...

  • Page 10

    7 the following figures show the cable schematic for both straight-through type and crossover type. Straight through cable schematic cross over cable schematic  fiber port the fiber port of sc type connector can work in multi mode or single mode. When you connect the fiber port to another one, plea...

  • Page 11: Cabling

    8 cabling  twisted-pair segments can be connected with an unshielded twisted pair (utp) or shielded twisted pair (stp) cable. The cable must comply with the ieee 802.3u 100base tx standard (e.G. Category 5, 5e, or 6). The cable between the equipment and the link partner (switch, hub, workstation, e...

  • Page 12: Wiring The Power Inputs

    9 wiring the power inputs please follow the steps below to insert the power wire. Insert the positive and negative wires into the pwr1 (v1+, v1-) and pwr2 (v2+,v2-) contacts on the terminal block connector. Tighten the wire-clamp screws to prevent the wires from loosening. Note use copper conductors...

  • Page 13: Dip Switch Settings

    10 on: enables the corresponding port alarm. If the port ’s link fails, the relay will form an open circuit and the fault led will turn on. Off: disables the corresponding port alarm. The relay will form a closed circuit and the fault led will never turn on. B.S.P. On: enables broadcast storm protec...

  • Page 14: Mounting Installation

    11 mounting installation din-rail mounting the din-rail is screwed on the industrial switch from the factory. If the din-rail is not screwed on the industrial switch, please see the following pictures to screw the din-rail on the switch. Follow the steps below to hang the industrial switch. 1. Use t...

  • Page 15

    12 din-rail on to the track. 4. Then, lightly pull down the bracket on to the rail. 5. Check if the bracket is mounted tight on the rail. 6. To remove the industrial switch from the rail, reverse steps above..

  • Page 16: Wall Mounting

    13 wall mounting follow the steps below to mount the industrial switch using the wall mount bracket. 1. Remove the din-rail bracket from the industrial switch; loosen the screws to remove the din-rail. 2. Place the wall mount bracket on the top and bottom of the industrial switch. 3. Use the screws ...

  • Page 17: Hardware Installation

    14 hardware installation this section is to explain how to install the lnx-0602 series – 6-port industrial unmanaged ethernet switch with fiber. Installation steps 1. Unpack the industrial switch packing. 2. Check if the din-rail bracket is screwed on the industrial switch. If the din-rail is not sc...

  • Page 18: Network Application

    15 network application this segment provides an example of an industrial switch application..

  • Page 19: Troubleshooting

    16 troubleshooting  verify the right power cord/adapter, never use power supply/adapter with non- compliant dc output voltage, or it will burn the equipment.  select the proper utp/stp cable to construct the network with using the right cable. Use unshielded twisted-pair (utp) or shield twisted-pa...

  • Page 20: Technical Specification

    17 technical specification the lnx-0602 series - 6-port industrial unmanaged ethernet switch with fiber technical specifications is shown below. Standard ieee 802.3 10base-t ethernet ieee 802.3u 100base-tx fast ethernet ieee802.3x flow control and back pressure protocol csma/cd transfer rate 14,880 ...

  • Page 21

    18 max power consumption 7.5 watts installation din rail mounting, wall mounting operating temp. Standard operating temperature: -10 o c to 70 o c extend operating temperature: -40 o c to 75 o c operating humidity 5% to 95% (non-condensing) storage temperature -40 o c to 85 o c case dimension ip-30,...