1. DL manuals
  2. ANTAIRA
  3. Switch
  4. LNP-0500G-24 Series
  5. User Manual

ANTAIRA LNP-0500G-24 Series User Manual

Manual is about: 5-Port Industrial Gigabit PoE+ Unmanaged Ethernet Switches with 4*10/100/1000Tx (30W/Port) + 1*10/100/1000Tx, 12~36VDC (Built-in Voltage Booster)

Summary of LNP-0500G-24 Series

  • Page 1

    Antaira technologies - industrial ethernet switches lnp-0500g series user manual v1.0 i lnp-0500g-24 series 5-port industrial gigabit poe+ unmanaged ethernet switches with 4*10/100/1000tx (30w/port) + 1*10/100/1000tx, 12~36vdc (built-in voltage booster) version 1.2 user manual.

  • Page 2

    Antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 ii © copyright 2018 antaira technologies, llc all rights reserved this document contains information, which is protected by copyright. Reproduction, adaptation or translation without prior permission is prohibit...

  • Page 3

    Antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 3 fcc notice this equipment has been tested and found to comply with the limits for a class-a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection agai...

  • Page 4

    Antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 4 table of contents 1.Overview ....................................................................... 1 1.1 key features ...................................................... 1 1.2 package contents ..............

  • Page 5

    Antaira technologies - industrial ethernet switches lnp-0500g series user manual v1.2 1 1. Overview antaira technologies’ lnp-0500g-24 series is an industrial gigabit poe+ unmanaged ethernet switch featuring 4*10/100/1000tx poe rj45 ports and 1*10/100/1000tx rj45 port. Each poe ethernet port support...

  • Page 6

    2 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 1.2 package contents  1 - lnp-0500g-24 (-t): 5-port industrial gigabit poe+ unmanaged ethernet switch with 4*10/100/1000tx (30w/port) and 1*10/100/1000tx  1 - product cd  2 - w all mounting brackets and scr...

  • Page 7

    3 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 2. Hardware description 2.1 physical dimensions figure 2.1, below, shows the physical dimensions of antaira technologies’ lnp-0500g-24 series: 5-port industrial gigabit poe+ unmanaged ethernet switch with 4*10...

  • Page 8

    4 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 2.2 front panel the front panel of the lnp-0500g-24 series: 5-port gigabit industrial poe+ unmanaged ethernet switch with 4*10/100/1000tx (30w/port) and 1*10/100/1000tx. See figure 2.2. 6-pin removal terminal ...

  • Page 9

    5 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 2.4 led indicators there are led light indicators located on the front panel of the industrial ethernet switch that display the power status and network status. Each led indicator has a different color and has...

  • Page 10

    6 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 rj-45 pin assignments (table 2.2) pin number assignment 1 rx+ 2 rx- 3 tx+ 6 tx- table 2.2 rj45 pin assignments note: the “+” and “-” signs represent the polarity of the wires that make up each wire pair. All p...

  • Page 11

    7 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 2.6 cabling  twisted-pair segments can be connected with an unshielded twisted pair (utp) or shielded twisted pair (stp) cable. The cable must comply with the ieee 802.3u 100base tx standard (e.G. Category 5,...

  • Page 12

    8 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 2.8 wiring the fault alarm contact the fault alarm contact is in the middle of the terminal block connector as the picture shows below in figure 2.8. By inserting the wires, it will detect the fault status inc...

  • Page 13

    9 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 3. Mounting installation 3.1 din-rail mounting the din-rail is pre-installed on the industrial ethernet switch from the factory. If the din-rail is not on the industrial ethernet switch, please refer to figure...

  • Page 14

    10 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 follow the steps below to learn how to hang the industrial ethernet switch. 1. Use the screws to install the din-rail bracket on the rear side of the industrial ethernet switch. 2. To remove the din-rail brac...

  • Page 15

    11 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 3.2 wall mounting follow the steps below to mount the industrial ethernet switch using the wall mounting bracket as shown below in figure 3.4. 1. Remove the din-rail bracket from the industrial ethernet switc...

  • Page 16

    12 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 4. Hardware installation 4.1 installation steps this section will explain how to install antaira technologies’ lnp-0500g-24 (-t): 5-port industrial gigabit poe+ unmanaged ethernet switch with 4*10/100/1000tx ...

  • Page 17

    13 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 5. Network application this segment provides an example of an industrial ethernet switch application (figure 5.1). Figure 5.1 networking application example.

  • Page 18

    14 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 6. Trouble shooting always verify to have the right power cord or adapter. Never use a power supply or adapter with a non-compliant dc output voltage or it will burn the equipment. Select the proper utp or st...

  • Page 19

    15 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 7. Technical specifications table 7.1 has the technical specifications for antaira technologies lnp-0500g series: 5-port industrial gigabit poe+ unmanaged ethernet switch with 4*10/100/1000tx (30w/port), and ...

  • Page 20

    16 antaira technologies - industrial ethernet switches lnp-0500g-24 series user manual v1.2 stability testing iec60068-2-32 (free fall) iec60068-2-27 (shock) iec60068-2-6 (vibration) safety ul 61010-1, ul 61010-2-201, ul class 1 division 2, isa 12.12.01 table 7.1 lnp-0500g-24 series technical specif...