- DL manuals
- ANTAIRA
- Switch
- LNP-0501-M-24
- User Manual
ANTAIRA LNP-0501-M-24 User Manual
Summary of LNP-0501-M-24
Page 1
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v1.0 i lnp-0501-24 series 5-port industrial poe+ unmanaged ethernet switches with 4*10/100tx (30w/port) + 1*10/100tx, 12~36vdc input (voltage booster) user manual version 2.0
Page 2
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 ii © copyright 2015 antaira technologies, llc all rights reserved this document contains information, which is protected by copyright. Reproduction, adaptation or translation without prior permission is prohibite...
Page 3
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 iii fcc notice this equipment has been tested and found to comply with the limits for a class-a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection aga...
Page 4: Table Of Contents
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 iv table of contents 1.Overview ....................................................................... 1 1.1 key features ...................................................... 1 1.2 package contents ..............
Page 5: 1. Overview
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v1.0 1 1. Overview a ntaira technologies’ lnp-0501-24 series is an industrial poe+ unmanaged ethernet switch featuring 4*10/100tx fast ethernet rj45 ports and 1*100fx fiber port with sc or st type connectors and an op...
Page 6: 1.2 Package Contents
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 2 case/installation ip-30 protection din-rail and wall mount design 1.2 package contents 1 - lnp-0501-24 (t): 5-port industrial poe+ unmanaged ethernet switch with 4*10/100tx (30w/port), 1*100fx fiber sc/st typ...
Page 7: 2. Hardware Description
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 3 2. Hardware description 2.1 physical dimensions figure 2.1, below, shows the physical dimensions of antaira technologies’ lnp-0501-24 series: 5- port industrial poe+ unmanaged ethernet switch with 4*10/100tx (3...
Page 8: 2.2 Front Panel
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 4 2.2 front panel the front panel of the lnp-0501-24 series: 5-port industrial poe+ unmanaged ethernet switch with 4*10/100tx (30w/port), 1*100fx fiber sc/st type connector (multi-mode 2km, or single-mode 30km); ...
Page 9: 2.4 Led Indicators
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 5 2.4 led indicators there are led light indicators located on the front panel of the industrial ethernet switch that display the power status and network status. Each led indicator has a different color and has ...
Page 10
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 6 rj-45 pin assignments (table 2.2) pin number assignment 1 rx+ 2 rx- 3 tx+ 6 tx- all ports on this industrial ethernet switch support automatic mdi/mdi-x operations. Users can use straight-through cables (see fi...
Page 11: 2.6 Cabling
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 7 fiber port the fiber port of the sc type connector can work in multi-mode or single-mode. When connecting the fiber port to another one, please connect accordingly following the figure below. The wrong connecti...
Page 12
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 8 2.7 wiring the power inputs please follow the steps below to insert the power wire. 1. Insert the positive and negative wires into the pwr1 (v1+, v1-) and pwr2 (v2+, v2-) contacts on the terminal block connecto...
Page 13
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 9 2.8 wiring the fault alarm contact the fault alarm contact is in the middle of the terminal block connector as the picture shows below in figure 2.9. By inserting the wires, it will detect the fault status incl...
Page 14: 3. Mounting Installation
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 10 3. Mounting installation 3.1 din-rail mounting the din-rail is pre-installed on the industrial ethernet switch from the factory. If the din-rail is not on the industrial ethernet switch, please refer to figure...
Page 15
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 11 follow the steps below to learn how to hang the industrial ethernet switch. 1. Use the screws to install the din-rail bracket on the rear side of the industrial ethernet switch. 2. To remove the din-rail brack...
Page 16: 3.2 Wall Mounting
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 12 3.2 wall mounting follow the steps below to mount the industrial ethernet switch using the wall mounting bracket as shown below in figure 3.4. 1. Remove the din-rail bracket from the industrial ethernet switch...
Page 17: 4. Hardware Installation
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 13 4. Hardware installation 4.1 installation steps this section will explain how to install antaira technologies’ lnp-0501-24 (t): 5-port industrial poe+ unmanaged ethernet switch with 4*10/100tx (30w/port), 1*10...
Page 18: 5. Network Application
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 14 5. Network application this segment provides an example of an industrial ethernet switch application (figure 5.1). Figure 5.1 industrial poe ethernet switch application reference.
Page 19: 6. Trouble Shooting
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 15 6. Trouble shooting always verify to have the right power cord or adapter. Never use a power supply or adapter with a non-compliant dc output voltage or it will burn the equipment. Select the proper utp or stp...
Page 20: 7. Technical Specifications
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 16 7. Technical specifications table 7.1 has the technical specifications for antaira technologies ’ lnp-0501-24 series: 5-port industrial poe+ unmanaged ethernet switch with 4*10/100tx (30w/port), 1*100fx fiber ...
Page 21
Antaira technologies - industrial ethernet switches lnp-0501-24 series user manual v2.0 17 fault output 1 relay output max power consumption 145 watts (full load with poe function) installation din-rail mounting, wall mounting (optional) operating temperature standard: -10 o c to 70 o c (14° to 158°...