1. DL manuals
  2. ANTAIRA
  3. Switch
  4. LNX-500A
  5. User Manual

ANTAIRA LNX-500A User Manual

Other manuals for LNX-500A: User manual
Manual is about: 5-port / 8-port 10/100BaseTX Industrial Ethernet Switch

Summary of LNX-500A

  • Page 1

    Product user manual and enterprise branch and head offices lnx-500a $17$,5$ www.Enochsystems.Com 1-877-722-1116 sales@enochsystems.Com copyright © 2013 enoch systems, llc, enoch systems and the enoch systems logo are trademarks or registered trademarks of enoch systems, llc and/or its affiliates in ...

  • Page 2: Industrial Ethernet Switch

    5-port / 8-port 10/100basetx industrial ethernet switch user manual.

  • Page 3: Content

    Content overview ............................................................ 1 introduction .............................................................. 1 features ................................................................... 3 packing list .....................................................

  • Page 4

    Installation steps .................................................... 14 troubles shooting ............................................. 16 technical specification .................................... 17.

  • Page 5: Overview

    1 overview introduction this user manual is suitable for the products as follows: • 5-port 10/100tx unmanaged industrial switch • 8-port 10/100tx unmanaged industrial switch the unmanaged industrial switch is a cost-effective solution and meets the high reliability requirements demanded by industria...

  • Page 6

    2 wide operating temperature the operating temperature of the industrial switch is between -40 ~ 80 ℃ (wide operating temperature model) or -10 ~ 70 ℃ (standard model). With such a wide range, you can use the industrial switch in some of the harshest industrial environments that exist. Easy troubles...

  • Page 7: Features

    3 features  provides 5 x 10/100 mbps (5-port 10/100tx model) or 8 x 10/100 mbps (8-port 10/100tx model) ethernet ports.  supports full/half duplex flow control  supports mdi/mdi-x auto-crossover  supports surge (eft) protection 3,000 vdc for power line  supports 4,000 vdc ethernet esd protectio...

  • Page 8: Packing List

    4 packing list  1 x 5-port 10/100tx industrial ethernet switch, or 1x 8-port 10/100tx industrial ethernet switch  1 x user manual  2 x wall mounting bracket and screws safety precaution attention if dc voltage is supplied by an external circuit, please use a protection device on the power supply ...

  • Page 9: Hardware Description

    5 hardware description in this paragraph, we will introduce the industrial switch’s hardware spec, port, cabling information, and wiring installation. Front panel the front panel of the 5-port and 8-port 10/100basetx industrial switch is shown as below. Front panel of the 5-port & 8-port 10/100baset...

  • Page 10: Top View

    6 top view the top panel of the 5-port & 8-port 10/100basetx industrial switch is equipped one terminal block connector of two dc power inputs. Top panel of the 5-port & 8-port 10/100basetx industrial switch wiring the power inputs please follow the steps below to insert the power wire. 1. Insert th...

  • Page 11

    7 wiring the fault alarm contact the fault alarm contact is in the middle of terminal block connector as the picture shows below. Inserting the wires, it will detect the fault status which the power is failure or port link failure (for managed model) and form an open circuit. Note the wire gauge for...

  • Page 12: Led Indicators

    8 led indicators there are few leds display the power status and network status located on the front panel of the industrial switch, each of them has its own specific meaning as below table. Led color description p1 green on power input 1 is active off power input 1 is inactive p2 green on power inp...

  • Page 13

    9 6 rx- note “+” and “-” signs represent the polarity of the wires that make up each wire pair. All ports on this industrial switch support automatic mdi/mdi-x operation, you can use straight-through cables (see figure below) for all network connections to pcs or servers, or to other switches or hub...

  • Page 14: Cabling

    10 cabling use the four twisted-pair, category 5 cabling for rj-45 port connection. The cable between the converter and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long..

  • Page 15: Mounting Installation

    11 mounting installation din-rail mounting the din-rail is screwed on the industrial switch when out of factory. If the din-rail is not screwed on the industrial switch, please see the following figure to screw the din-rail on the switch. Follow the below steps to hang the industrial switch. 1. Use ...

  • Page 16

    12 3. First, insert the top of din-rail into the track. 4. Then, lightly push the button of din-rail into the track. 5. Check the din-rail is tightly on the track. 6. To remove the industrial switch from the track, reverse steps above..

  • Page 17: Wall Mount Plate Mounting

    13 wall mount plate mounting follow the steps below to mount the industrial switch with wall mount plate. 1. Remove the din-rail from the industrial switch; loose the screws to remove the din-rail. 2. Place the wall mount plate on the rear panel of the industrial switch. 3. Use the screws to screw t...

  • Page 18: Hardware Installation

    14 hardware installation in this paragraph, we will describe how to install the 5-port or 8-port 10/100base-tx industrial switch and the installation points for the attention. Installation steps 1. Unpack the industrial switch packing. 2. Check the din-rail is screwed on the industrial switch. If th...

  • Page 19

    15 4. Power on the industrial switch. How to wire the power; please refer to the wiring the power inputs section. The power led on the industrial switch will light up. Please refer to the led indicators section for meaning of led lights. 5. Prepare the twisted-pair, straight through category 5 cable...

  • Page 20: Troubles Shooting

    16 troubles shooting  verify that you are using the right power cord/adapter (dc 12-48v), please don’t use the power adapter with dc output bigger than 48v, or it will burn this converter down.  select the proper utp cable to construct your network. Please check that you are using the right cable....

  • Page 21: Technical Specification

    17 technical specification the technical specifications of the industrial switch are listed as follows. Communications compatibility ieee 802.3, 802.3u lan 10/100base-tx transmission distance up to 100 m transmission speed up to 100 mbps interface connectors 5 x rj-45 (5-port 10/100tx) 8 x rj-45 (8-...

  • Page 22

    18 mechanism dimensions (wxhxd) 30 x 95 x 140 enclosure ip-30, metal shell with solid mounting kits mounting din35 rail, wall protection esd (ethernet) 4,000 vdc surge (eft for power) 3,000 vdc power reverse yes environment operating temperature -40 ~ 80 ℃ (wide operating temp. Model) -10 ~ 70 ℃ (st...

  • Page 23

    19 ce en61000-4-2 (esd) ce en61000-4-3 (rs) ce en61000-4-4 (eft) ce en61000-4-5 (surge) ce en61000-4-6 (cs) ce en61000-4-8 ce en61000-4-11 ce en61000-4-12 ce en61000-6-2 ce en61000-6-4 free fall iec60068-2-32 shock iec60068-2-27 vibration iec60068-2-6.