1. DL manuals
  2. ANTAIRA
  3. Network Router
  4. LNX-800AG
  5. User manual

ANTAIRA LNX-800AG User manual

Manual is about: 8-Port Industrial Gigabit Unmanaged Ethernet Switches w/8*10/100/1000Tx

Summary of LNX-800AG

  • Page 1

    Lnx-800ag 8-port industrial gigabit unmanaged ethernet switches - w/8*10/100/1000tx user manual.

  • Page 2: Fcc Warning

    Fcc warning this equipment has been tested and found to comply with the limits for a class-a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, an...

  • Page 3: Table Of Contents

    Table of contents introduction ................................................................ 1 features ................................................................... 1 package contents .................................................... 2 hardware description .................................

  • Page 4: Introduction

    1 introduction antaira’s lnx-800ag is a smart 8-port industrial gigabit unmanaged ethernet switch supporting 8-port 10/100/1000tx that can automatically sense transmission speeds of 10/100/1000 mbps. The rj-45 interface can also be auto-detected, so mdi or mdi-x is automatically selected and a cross...

  • Page 5: Package Contents

    2  case/installation  ip-30 protection  installation in pollution degree 2 environment  din rail and wall mount design  provides eft protection 3,000 vdc for power line  supports 6,000 vdc ethernet esd protection package contents please refer to the package contents list below.  lnx-800ag - 8...

  • Page 6: Hardware Description

    3 hardware description t he industrial switch’s hardware spec, port, cabling information, and wiring installation will be described below. Physical dimension the lnx-500ag - 5-port industrial gigabit unmanaged ethernet switch dimensions: (w x d x h) 30mm x 95mm x 140mm.

  • Page 7: Front Panel

    4 front panel the front panel of the industrial switch is shown below: front panel of the industrial switch top view the top view of the industrial switch has one terminal block connector of two dc power inputs and relay circuit contact. Top view of the industrial switch.

  • Page 8: Led Indicators

    5 led indicators the diagnostic leds located on the front panel of the industrial switch provide real-time information of the system and optional status. The following table provides the description of the led status. Led color description p1 green on power input 1 is active off power input 1 is ina...

  • Page 9

    6 all ports on this industrial switch support an automatic mdi/mdi-x operation, and users can use straight-through cables (see figure below) for all network connections to pcs or servers, or to other switches or hubs. With straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are con...

  • Page 10: Cabling

    7 the following figure shows the 10/100/1000 ethernet rj-45 pin outs. Cabling  use unshielded twisted-pair (utp) or shielded twisted-pair (stp) cable for rj-45 connections: 100Ω category 3, 4 or 5 cable for 10mbps connections, 100Ω category 5 cable for 100mbps, or 100Ω category 5e/above cable for 1...

  • Page 11

    8 2. Tighten the wire-clamp screws to prevent the wires from loosening. Note the wire gauge for the terminal block should be in the range between 12~ 24 awg. If only using one power source, jumper pin 1 to pin 5 and pin 2 to pin 6 to eliminate power fault alarm. Wiring the fault alarm contact the fa...

  • Page 12: Mounting Installation

    9 mounting installation din-rail mounting the din-rail is screwed on the industrial switch from the factory. If the din-rail is not screwed on the industrial switch, please see the following pictures to screw the din-rail on the switch. Follow the steps below to hang the industrial switch. 1. Use th...

  • Page 13

    10 3. After the din-rail bracket is screwed on the rear side of the switch, insert the top of din-rail on to the track. 4. Then, lightly pull down the bracket on to the rail. 5. Check if the bracket is mounted tight on the rail. 6. To remove the industrial switch from the rail, reverse steps above..

  • Page 14: Wall Mounting

    11 wall mounting follow the steps below to mount the industrial switch using the wall mount bracket. 1. Remove the din-rail bracket from the industrial switch; loosen the screws to remove the din-rail. 2. Place the wall mount bracket on the top and bottom of the industrial switch. 3. Use the screws ...

  • Page 15: Hardware Installation

    12 hardware installation this section is to explain how to install the lnx-500ag – 5-port industrial gigabit unmanaged ethernet switch. Installation steps 1. Unpack the industrial switch packing. 2. Check if the din-rail bracket is screwed on the industrial switch. If the din-rail is not screwed on ...

  • Page 16: Network Application

    13 network application this segment provides an example of an industrial switch application..

  • Page 17: Troubleshooting

    14 troubleshooting  verify the right power cord/adapter, never use power supply/adapter with non- compliant dc output voltage, or it will burn the equipment.  select the proper utp/stp cable to construct the network with using the right cable. Use unshielded twisted-pair (utp) or shield twisted-pa...

  • Page 18: Technical Specification

    15 technical specification the lnx-800ag - 8-port industrial gigabit unmanaged ethernet switch technical specifications are shown below. Standard ieee 802.3 10base-t ethernet ieee 802.3u 100base-tx fast ethernet ieee 802.3ab 1000base-tx gigabit ethernet ieee802.3x flow control and back pressure prot...

  • Page 19

    16 installation din rail mounting, wall mounting operating temp. Standard operating temperature: -10 o c to 70 o c extend operating temperature: -40 o c to 75 o c operating humidity 5% to 95% (non-condensing) storage temperature -40 o c to 85 o c case dimension ip-30, 30mm (w) x 95mm (d) x 140mm (h)...