1. DL manuals
  2. ANTAIRA
  3. Media Converter
  4. Optolinx fcu-2805p
  5. User manual

ANTAIRA Optolinx fcu-2805p User manual

Manual is about: 1000Base-X to 10/100/1000Base-T 802.3at PoE Media Converter

Summary of Optolinx fcu-2805p

  • Page 1

    1000base-x to 10/100/1000base-t 802.3at poe media converter user’s manual.

  • Page 2: Trademarks

    Trademarks copyright © antaira technologies 2013. Contents subject to revision without prior notice. Antaira is a registered trademark of antaira technologies. The information in this manual is subject to change without notice. All other trademarks belong to their respective owners. Disclaimer antai...

  • Page 3: Fcc Warning

    Fcc warning this equipment has been tested and found to comply with the regulations for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. ...

  • Page 4: Weee Warning

    Weee warning to avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dis...

  • Page 5: Table Of Contents

    Table of contents 1. Overview ......................................................................... 6 about the power over ethernet injector .............................. 6 2. Checklist .......................................................................... 7 3. Product outlook ................

  • Page 6: 1. Overview

    6 1. Overview thank you for purchasing the antaira 1000base-x fiber-optic to 10/100/1000mbps ethernet twisted pair 802.3at poe bridge converter. This converter is used to convert one type to another equivalent type of media signal that allows the two segments to connect easily, efficiently and inexp...

  • Page 7: 2. Checklist

    7 2. Checklist your fcu-2805p-sfp box should contain the following items: 1. 1000base-x to 10/100/1000base-t 802.3at poe media converter x 1 2. User’s manual x 1 3. Ac-dc adapter (input: 52v~56v dc, 0.58a max.) x 1 4. Power cord x 1 if any of these are missing or damaged, please contact your dealer ...

  • Page 8: 3. Product Outlook

    8 3. Product outlook overview the layout of the fcu-2805p-sfp 52v~56v dc lfp pwr mini-gbic off on fiber tx lnk act in use poe 10/100/1000base-t poe media converter 1000x to 10/100/1000t ethernet+dc figure 3-1: product outlook of the fcu-2805p-sfp.

  • Page 9: Left View

    9 left view there is one rj-45 twisted-pair jack (auto-mdi/mdi-x), one fiber-optic connector (vary by model) and four led indicators. Pwr mini-gbic fiber tx lnk act in use poe 10/100/1000base-t poe media converter 1000x to 10/100/1000t ethernet+dc figure 3-2: left view of fcu-2805p-sfp right view on...

  • Page 10

    10 4. Link fault pass through (lfp) the lfp function includes the link fault pass through function (llcf/llr) and the dip switch design. Llcf/llr can immediately alarm administrators to a link media problem and provide an efficient solution to monitor the net. The dip switch allows you to disable or...

  • Page 11: Link Loss Return (Llr)

    11 if the connection breaks, the fcu-2805p-sfp link loss forwards to the switch / hub and generates a trap to the management station. The administrator can then determine the source of the problem. Media converter management station switch/hub w/snmp management station media converter switch/hub w/s...

  • Page 12

    12 if one of the optical conductors is down (as shown in the diagram box below), the converter with llr function will return a no-link condition to its link partner. With the llcf function also enabled, the no-link condition is carried forward to the switch/hub where a trap is generated to the manag...

  • Page 13

    13 5. Installing the converter please follow these steps to install the poe+ media converter: 1. Turn off the power of the device / station in a network to which the fcu-2805p-sfp will be attached. 2. Ensure that there is no activity in the network. 3. Attach fiber cable from the fcu-2805p-sfp to th...

  • Page 14

    14 1000base-sx/lx sfp transceiver 10/100/1000base-t utp 1000base-sx/lx lc fiber figure 5-1: fcu-2805p-sfp installation note rj-45 / stp, utp cat5 / 5e / 6, straight / cross- over cable is accepted. Please refer to section 9 for more about the wiring distance of your tp, optic-fiber networks..

  • Page 15: 6. Poe Function

    15 6. Poe function fcu-2805p-sfp and the ieee 802.3at / 802.3af injector / splitter equipment installation: before your installation, we recommend that you check your network environment. If there are any ieee 802.3at / 802.3af devices needed to be powered on, the fcu-2805p-sfp can provide you a way...

  • Page 16

    16 for places that prove difficult to find a power inlet, the fcu-2805p-sfp provides the easiest way to power your ethernet devices with an internet camera or poe wireless access point installed in the wild range place. 550m~120km 100 meters fiber switch 1000 dc fcu-2805p-sfp power line (ac) ac dc p...

  • Page 17: 7. Led Indication

    17 7. Led indication system led color function pwr green light indicates the device is powered. 10/100/1000base-t port led color function lnk/act green blink indicates that the poe+ media converter is actively sending or receiving data over that port. Light indicates that the port is link up at 10/1...

  • Page 18

    18 8. Cable connection parameter the limitations are as below: duplex connection limitation (max.) twisted pair half / full node to node node to switch/hub 100 meters multi-mode converters mm half node to node node to switch 412 meters mm full node to node node to switch 220 / 550 meters single-mode...

  • Page 19

    19 9. Fcu-2805p-sfp technical specifications the fcu-2805p-sfp comes with the following standard features: • standard: ieee 802.3 / 802.3u / 802.3ab, 10/100/1000base-t and ieee 802.3at / 802.3af power over ethernet standard • connectors: • 1 x rj-45 (auto-mdi/mdi-x) twisted pair, eia568 w/ poe • 1 x...

  • Page 20: Appendix A

    20 appendix a a.1 device's rj-45 pin assignments 1000mbps, 1000base-t rj-45 connector pin assignment contact mdi mdi-x 1 bi_da+ bi_db+ 2 bi_da- bi_db- 3 bi_db+ bi_da+ 4 bi_dc+ bi_dd+ 5 bi_dc- bi_dd- 6 bi_db- bi_da- 7 bi_dd+ bi_dc+ 8 bi_dd- bi_dc- 10/100mbps, 10/100base-tx rj-45 connector pin assignm...

  • Page 21

    21 a.2 rj-45 cable pin assignment there are 8 wires on a standard utp/stp cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: straight cable crossover cable side 1 side 1 side 2 side 1 side 2 1 2 3 4 5 6 7 8 1 2 3 4 5...

  • Page 22

    22 a.3 fiber optical cable connection parameter the wiring details are as below: fiber optical patch cables: standard fiber type cable specification 1000base-sx (850nm) multi-mode 50/125μm or 62.5/125μm 1000base-lx (1300nm) multi-mode 50/125μm or 62.5/125μm single-mode 9/125μm.

  • Page 23

    23.